30 ноября 2025 г. 21:46:19 UTC, Klemens Nanni <[email protected]> пишет:
>U-boot has had support for years, but it is enabled by default only
>for some boards/targets.
>
>After I flashed my NanoPi R6S's eMMC (no SD-card) as per INSTALL.arm64:
>
>       => setenv serverip6 fe80::1
>       => tftpboot BOOTAA64.EFI -ipv6
>       ROUTER SOLICITATION 1
>       Set gatewayip6: fe80:0000:0000:0000:fce1:baff:fed0:2e5c, prefix_length: 
> 64
>       Using ethernet@fe1c0000 device
>       TFTP from server fe80:0000:0000:0000:0000:0000:0000:0001; our IP 
> address is fe80:0000:0000:0000:5c27:b1ff:fe14:a9c9
>       Filename 'BOOTAA64.EFI'.
>       Load address: 0xc00800
>       Loading: ################
>                1.7 MiB/s
>       done
>       Bytes transferred = 229585 (380d1 hex)
>       => bootefi $loadaddr
>       Booting /BOOTAA64.EFI
>       disks: sd0
>       >> OpenBSD/arm64 BOOTAA64 1.22
>       boot> 
>
>iPXE also boots this way, but then hangs, at least on the serial:
>
>       Booting /ipxe.efi
>       iPXE initialising devices...
>
>
>       iPXE 1.21.1+ (ge9a2) -- Open Source Network Boot Firmware -- 
> https://ipxe.org
>       Features: DNS HTTP iSCSI TFTP VLAN SRP AoE EFI Menu
>
>       Press Ctrl-B for the iPXE command line...
>
>I'll investigate that next, but IPv6 itself works fine incl. the
>ping6 and pxe commands.
>
>I don't use DHCPv6 and omitting it causes interactive prompts,
>hence why it's disabled.
>
>Image size growth seems negligible:
>
>       $  du -k u-*
>       9408    u-boot-rockchip.bin
>       9424    u-boot-rockchip.bin.new
>
>Feedback? OK?
>
>
>Index: Makefile
>===================================================================
>RCS file: /cvs/ports/sysutils/u-boot/rk3588/Makefile,v
>diff -u -p -r1.10 Makefile
>--- Makefile   9 Aug 2025 09:53:19 -0000       1.10
>+++ Makefile   30 Nov 2025 20:23:33 -0000
>@@ -1,4 +1,5 @@
> VERSION=      2025.07
>+REVISION=     0
> 
> SOC=          rk3588
> 
>@@ -27,6 +28,11 @@ EXTRACT_ONLY=       ${DISTNAME}${EXTRACT_SUFX}
> 
> MAKE_ENV+=    BL31=${FULLDISTDIR}/${RK3588_BL31}
> 
>+ENABLE_OPTS=  IPV6 \
>+              IPV6_ROUTER_DISCOVERY \
>+              CMD_PING6
>+DISABLE_OPTS= CMD_DHCP6
>+
> pre-build:
>       cc -o ${WRKSRC}/rkbinpatch ${FILESDIR}/rkbinpatch.c 
>       cd ${WRKSRC} && \
>@@ -41,7 +47,9 @@ do-build:
>               O="build/${BOARD}" \
>               -f ${MAKE_FILE} "${BOARD}"_defconfig
>       cd ${WRKSRC}/build/${BOARD} && \
>-          ../../scripts/config --set-val BAUDRATE 115200
>+          ../../scripts/config --set-val BAUDRATE 115200 \
>+              ${ENABLE_OPTS:=-e %} \
>+              ${DISABLE_OPTS:=-d %}
>       cd ${WRKSRC} && \
>           ${SETENV} ${MAKE_ENV} ROCKCHIP_TPL=${RK3588_TPL} ${MAKE_PROGRAM} \
>               ${MAKE_FLAGS} O="build/${BOARD}" \
>

Anyone?

Reply via email to