From: Todd Fujinaka <todd.fujin...@intel.com>
The i210 has two EEPROM access registers that are located in
non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously
and EEMNGCTL should also be corrected.
Reported-by: Roman Hodek <roman....@siemens.com>
Signed-off-by: Todd Fujinaka <todd.fujin...@intel.com>
Tested-by: Aaron Brown <aaron.f.br...@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirs...@intel.com>
---
drivers/net/ethernet/intel/igb/e1000_82575.c | 1 +
drivers/net/ethernet/intel/igb/e1000_i210.c | 27 +++++++++++++++++++++++++++
drivers/net/ethernet/intel/igb/e1000_i210.h | 1 +
drivers/net/ethernet/intel/igb/e1000_regs.h | 1 +
4 files changed, 30 insertions(+)
diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c
b/drivers/net/ethernet/intel/igb/e1000_82575.c
index d9664c4..362911d 100644
--- a/drivers/net/ethernet/intel/igb/e1000_82575.c
+++ b/drivers/net/ethernet/intel/igb/e1000_82575.c
@@ -299,6 +299,7 @@ static s32 igb_init_phy_params_82575(struct e1000_hw *hw)
case I210_I_PHY_ID:
phy->type = e1000_phy_i210;
phy->ops.check_polarity = igb_check_polarity_m88;
+ phy->ops.get_cfg_done = igb_get_cfg_done_i210;
phy->ops.get_phy_info = igb_get_phy_info_m88;
phy->ops.get_cable_length = igb_get_cable_length_m88_gen2;
phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82580;
diff --git a/drivers/net/ethernet/intel/igb/e1000_i210.c
b/drivers/net/ethernet/intel/igb/e1000_i210.c
index 65d9316..29f59c7 100644
--- a/drivers/net/ethernet/intel/igb/e1000_i210.c
+++ b/drivers/net/ethernet/intel/igb/e1000_i210.c
@@ -900,3 +900,30 @@ s32 igb_pll_workaround_i210(struct e1000_hw *hw)
wr32(E1000_MDICNFG, mdicnfg);
return ret_val;
}
+
+/**
+ * igb_get_cfg_done_i210 - Read config done bit
+ * @hw: pointer to the HW structure
+ *
+ * Read the management control register for the config done bit for
+ * completion status. NOTE: silicon which is EEPROM-less will fail trying
+ * to read the config done bit, so an error is *ONLY* logged and returns
+ * 0. If we were to return with error, EEPROM-less silicon
+ * would not be able to be reset or change link.
+ **/
+s32 igb_get_cfg_done_i210(struct e1000_hw *hw)
+{
+ s32 timeout = PHY_CFG_TIMEOUT;
+ u32 mask = E1000_NVM_CFG_DONE_PORT_0;
+
+ while (timeout) {
+ if (rd32(E1000_EEMNGCTL_I210) & mask)
+ break;
+ usleep_range(1000, 2000);
+ timeout--;
+ }
+ if (!timeout)
+ hw_dbg("MNG configuration cycle has not completed.\n");
+
+ return 0;
+}
diff --git a/drivers/net/ethernet/intel/igb/e1000_i210.h
b/drivers/net/ethernet/intel/igb/e1000_i210.h
index 3442b63..eaa68a5 100644
--- a/drivers/net/ethernet/intel/igb/e1000_i210.h
+++ b/drivers/net/ethernet/intel/igb/e1000_i210.h
@@ -34,6 +34,7 @@ s32 igb_write_xmdio_reg(struct e1000_hw *hw, u16 addr, u8
dev_addr, u16 data);
s32 igb_init_nvm_params_i210(struct e1000_hw *hw);
bool igb_get_flash_presence_i210(struct e1000_hw *hw);
s32 igb_pll_workaround_i210(struct e1000_hw *hw);
+s32 igb_get_cfg_done_i210(struct e1000_hw *hw);
#define E1000_STM_OPCODE 0xDB00
#define E1000_EEPROM_FLASH_SIZE_WORD 0x11
diff --git a/drivers/net/ethernet/intel/igb/e1000_regs.h
b/drivers/net/ethernet/intel/igb/e1000_regs.h
index 4af2870..0fdcd4d 100644
--- a/drivers/net/ethernet/intel/igb/e1000_regs.h
+++ b/drivers/net/ethernet/intel/igb/e1000_regs.h
@@ -66,6 +66,7 @@
#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
#define E1000_PBS 0x01008 /* Packet Buffer Size */
#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
+#define E1000_EEMNGCTL_I210 0x12030 /* MNG EEprom Control */
#define E1000_EEARBC_I210 0x12024 /* EEPROM Auto Read Bus Control */
#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
#define E1000_I2CCMD 0x01028 /* SFPI2C Command Register - RW */
--
2.5.0
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
