The driver checks status of PCI power management to mark
default setting of Wake On Lan. On some systems this works, but often
it reports a that WOL is disabled when it isn't.
This patch gets rid of that check and just reports the wake on
lan status based on the hardware capablity.
Signed-off-by: Stephen Hemminger <[EMAIL PROTECTED]>
---
Please apply for 2.6.24.
--- a/drivers/net/sky2.c 2008-01-10 15:49:12.000000000 -0800
+++ b/drivers/net/sky2.c 2008-01-10 15:49:20.000000000 -0800
@@ -3946,7 +3946,7 @@ static __exit void sky2_debug_cleanup(vo
/* Initialize network device */
static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
unsigned port,
- int highmem, int wol)
+ int highmem)
{
struct sky2_port *sky2;
struct net_device *dev = alloc_etherdev(sizeof(*sky2));
@@ -3986,7 +3986,7 @@ static __devinit struct net_device *sky2
sky2->speed = -1;
sky2->advertising = sky2_supported_modes(hw);
sky2->rx_csum = (hw->chip_id != CHIP_ID_YUKON_XL);
- sky2->wol = wol;
+ sky2->wol = sky2_wol_supported(hw) & WAKE_MAGIC;
spin_lock_init(&sky2->phy_lock);
sky2->tx_pending = TX_DEF_PENDING;
@@ -4083,24 +4083,12 @@ static int __devinit sky2_test_msi(struc
return err;
}
-static int __devinit pci_wake_enabled(struct pci_dev *dev)
-{
- int pm = pci_find_capability(dev, PCI_CAP_ID_PM);
- u16 value;
-
- if (!pm)
- return 0;
- if (pci_read_config_word(dev, pm + PCI_PM_CTRL, &value))
- return 0;
- return value & PCI_PM_CTRL_PME_ENABLE;
-}
-
static int __devinit sky2_probe(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
struct net_device *dev;
struct sky2_hw *hw;
- int err, using_dac = 0, wol_default;
+ int err, using_dac = 0;
err = pci_enable_device(pdev);
if (err) {
@@ -4133,8 +4121,6 @@ static int __devinit sky2_probe(struct p
}
}
- wol_default = pci_wake_enabled(pdev) ? WAKE_MAGIC : 0;
-
err = -ENOMEM;
hw = kzalloc(sizeof(*hw), GFP_KERNEL);
if (!hw) {
@@ -4178,7 +4164,7 @@ static int __devinit sky2_probe(struct p
sky2_reset(hw);
- dev = sky2_init_netdev(hw, 0, using_dac, wol_default);
+ dev = sky2_init_netdev(hw, 0, using_dac);
if (!dev) {
err = -ENOMEM;
goto err_out_free_pci;
@@ -4215,7 +4201,7 @@ static int __devinit sky2_probe(struct p
if (hw->ports > 1) {
struct net_device *dev1;
- dev1 = sky2_init_netdev(hw, 1, using_dac, wol_default);
+ dev1 = sky2_init_netdev(hw, 1, using_dac);
if (!dev1)
dev_warn(&pdev->dev, "allocation for second device
failed\n");
else if ((err = register_netdev(dev1))) {
--
Stephen Hemminger <[EMAIL PROTECTED]>
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
