From: Rafał Miłecki <ra...@milecki.pl>
GPHY needs to be enabled to successfully probe & setup switch port
connected to it. Otherwise hardcoding PHY OUI would be required.
This prevents unimac_mdio_read() from getting MDIO_READ_FAIL.
Before:
brcm-sf2 80080000.switch lan4 (uninitialized): PHY [800c05c0.mdio--1:08] driver
[Generic PHY] (irq=POLL)
brcm-sf2 80080000.switch lan3 (uninitialized): PHY [800c05c0.mdio--1:09] driver
[Generic PHY] (irq=POLL)
brcm-sf2 80080000.switch lan2 (uninitialized): PHY [800c05c0.mdio--1:0a] driver
[Generic PHY] (irq=POLL)
brcm-sf2 80080000.switch lan1 (uninitialized): PHY [800c05c0.mdio--1:0b] driver
[Generic PHY] (irq=POLL)
brcm-sf2 80080000.switch wan (uninitialized): error -5 setting up PHY for tree
0, switch 0, port 7
After:
brcm-sf2 80080000.switch lan4 (uninitialized): PHY [800c05c0.mdio--1:08] driver
[Generic PHY] (irq=POLL)
brcm-sf2 80080000.switch lan3 (uninitialized): PHY [800c05c0.mdio--1:09] driver
[Generic PHY] (irq=POLL)
brcm-sf2 80080000.switch lan2 (uninitialized): PHY [800c05c0.mdio--1:0a] driver
[Generic PHY] (irq=POLL)
brcm-sf2 80080000.switch lan1 (uninitialized): PHY [800c05c0.mdio--1:0b] driver
[Generic PHY] (irq=POLL)
brcm-sf2 80080000.switch wan (uninitialized): PHY [800c05c0.mdio--1:0c] driver
[Generic PHY] (irq=POLL)
Signed-off-by: Rafał Miłecki <ra...@milecki.pl>
---
Below you can see backtrace after adding
WARN(1, "MDIO_READ_FAIL\n");
to the unimac_mdio_read() for the (cmd & MDIO_READ_FAIL) condition.
[ 0.584058] brcm-sf2 80080000.switch: found switch: BCM4908, rev 0
[ 0.596214] brcm-sf2 80080000.switch lan4 (uninitialized): PHY
[800c05c0.mdio--1:08] driver [Generic PHY]
[ 0.612212] brcm-sf2 80080000.switch lan3 (uninitialized): PHY
[800c05c0.mdio--1:09] driver [Generic PHY]
[ 0.628216] brcm-sf2 80080000.switch lan2 (uninitialized): PHY
[800c05c0.mdio--1:0a] driver [Generic PHY]
[ 0.644215] brcm-sf2 80080000.switch lan1 (uninitialized): PHY
[800c05c0.mdio--1:0b] driver [Generic PHY]
[ 0.656212] ------------[ cut here ]------------
[ 0.660884] MDIO_READ_FAIL
[ 0.663685] WARNING: CPU: 0 PID: 128 at unimac_mdio_read+0x98/0xb8
[ 0.670016] Modules linked in:
[ 0.673156] CPU: 0 PID: 128 Comm: kworker/0:2 Not tainted 5.4.99 #0
[ 0.679603] Hardware name: Netgear R8000P (DT)
[ 0.684185] Workqueue: events deferred_probe_work_func
[ 0.689462] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 0.694389] pc : unimac_mdio_read+0x98/0xb8
[ 0.698690] lr : unimac_mdio_read+0x98/0xb8
[ 0.702989] sp : ffffffc0108d3840
[ 0.706394] x29: ffffffc0108d3840 x28: 0000000000000000
[ 0.711860] x27: ffffff801e8a8850 x26: ffffff801e8a8840
[ 0.717325] x25: ffffff801f257000 x24: 0000000000000000
[ 0.722790] x23: 0000000000002001 x22: 0000000000000001
[ 0.728256] x21: ffffff801f257000 x20: 0000000000001000
[ 0.733723] x19: ffffff801f34a080 x18: 000000000000000e
[ 0.739188] x17: 0000000000000001 x16: 0000000000000019
[ 0.744653] x15: 0000000000000033 x14: ffffffc01079daa0
[ 0.750119] x13: 0000000000000000 x12: ffffffc01079d000
[ 0.755584] x11: ffffffc010767000 x10: 0000000000000010
[ 0.761049] x9 : 0000000000000000 x8 : 0000000000000000
[ 0.766516] x7 : 0000000000000007 x6 : 000000000000006e
[ 0.771981] x5 : 0000000000000006 x4 : 0000000000000000
[ 0.777446] x3 : 0000000000000000 x2 : 00000000ffffffff
[ 0.782912] x1 : ffffffc010767158 x0 : 000000000000000e
[ 0.788379] Call trace:
[ 0.790890] unimac_mdio_read+0x98/0xb8
[ 0.794831] __mdiobus_read+0x40/0x58
[ 0.798594] mdiobus_read+0x48/0x70
[ 0.802177] genphy_read_abilities+0x84/0x158
[ 0.806657] phy_probe+0x160/0x1d8
[ 0.810153] phy_attach_direct+0x210/0x2c0
[ 0.814368] of_phy_attach+0x40/0x80
[ 0.818042] phylink_of_phy_connect+0x6c/0x120
[ 0.822611] dsa_slave_create+0x2b8/0x408
[ 0.826728] dsa_register_switch+0x888/0xa60
[ 0.831120] b53_switch_register+0x1c4/0x300
[ 0.835510] bcm_sf2_sw_probe+0x50c/0x640
[ 0.839631] platform_drv_probe+0x50/0xa0
[ 0.843752] really_probe+0xcc/0x2e0
[ 0.847425] driver_probe_device+0x54/0xe8
[ 0.851637] __device_attach_driver+0x80/0xb8
[ 0.856118] bus_for_each_drv+0x68/0xa8
[ 0.860059] __device_attach+0xcc/0x140
[ 0.864001] device_initial_probe+0x10/0x18
[ 0.868303] bus_probe_device+0x90/0x98
[ 0.872245] deferred_probe_work_func+0x6c/0xa0
[ 0.876907] process_one_work+0x1fc/0x390
[ 0.881026] worker_thread+0x278/0x4d0
[ 0.884882] kthread+0x120/0x128
[ 0.888195] ret_from_fork+0x10/0x1c
[ 0.891868] ---[ end trace 918e8c44c53d6f7b ]---
---
drivers/net/dsa/bcm_sf2.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index 70626547ffb3..6159d0a69870 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -1432,10 +1432,14 @@ static int bcm_sf2_sw_probe(struct platform_device
*pdev)
rev = reg_readl(priv, REG_PHY_REVISION);
priv->hw_params.gphy_rev = rev & PHY_REVISION_MASK;
+ bcm_sf2_gphy_enable_set(priv->dev->ds, true);
+
ret = b53_switch_register(dev);
if (ret)
goto out_mdio;
+ bcm_sf2_gphy_enable_set(priv->dev->ds, false);
+
dev_info(&pdev->dev,
"Starfighter 2 top: %x.%02x, core: %x.%02x, IRQs: %d, %d\n",
priv->hw_params.top_rev >> 8, priv->hw_params.top_rev & 0xff,
--
2.26.2
