On 18/09/2020 17:26:03+0200, Alexandre Belloni wrote:
> On 18/09/2020 04:07:23+0300, Vladimir Oltean wrote:
> > From: Vladimir Oltean <vladimir.olt...@nxp.com>
> >
> > The TX-timestampable skb is added late to the ocelot_port->tx_skbs. It
> > is in a race with the TX timestamp IRQ, which checks that queue trying
> > to match the timestamp with the skb by the ts_id. The skb should be
> > added to the queue before the IRQ can fire.
> >
> > Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
> > Signed-off-by: Vladimir Oltean <vladimir.olt...@nxp.com>
> > Reviewed-by: Horatiu Vultur <horatiu.vul...@microchip.com>
>
> Tested-by: Alexandre Belloni <alexandre.bell...@bootlin.com>
> Reviewed-by: Alexandre Belloni <alexandre.bell...@bootlin.com>
Ok, this misfired, sorry about the noise.
>
> > ---
> > Changes in v2:
> > None.
> >
> > drivers/net/ethernet/mscc/ocelot_net.c | 14 ++++++++------
> > 1 file changed, 8 insertions(+), 6 deletions(-)
> >
> > diff --git a/drivers/net/ethernet/mscc/ocelot_net.c
> > b/drivers/net/ethernet/mscc/ocelot_net.c
> > index 0668d23cdbfa..cacabc23215a 100644
> > --- a/drivers/net/ethernet/mscc/ocelot_net.c
> > +++ b/drivers/net/ethernet/mscc/ocelot_net.c
> > @@ -330,6 +330,7 @@ static int ocelot_port_xmit(struct sk_buff *skb, struct
> > net_device *dev)
> > u8 grp = 0; /* Send everything on CPU group 0 */
> > unsigned int i, count, last;
> > int port = priv->chip_port;
> > + bool do_tstamp;
> >
> > val = ocelot_read(ocelot, QS_INJ_STATUS);
> > if (!(val & QS_INJ_STATUS_FIFO_RDY(BIT(grp))) ||
> > @@ -344,10 +345,14 @@ static int ocelot_port_xmit(struct sk_buff *skb,
> > struct net_device *dev)
> > info.vid = skb_vlan_tag_get(skb);
> >
> > /* Check if timestamping is needed */
> > + do_tstamp = (ocelot_port_add_txtstamp_skb(ocelot_port, skb) == 0);
> > +
> > if (ocelot->ptp && shinfo->tx_flags & SKBTX_HW_TSTAMP) {
> > info.rew_op = ocelot_port->ptp_cmd;
> > - if (ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP)
> > + if (ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP) {
> > info.rew_op |= (ocelot_port->ts_id % 4) << 3;
> > + ocelot_port->ts_id++;
> > + }
> > }
> >
> > ocelot_gen_ifh(ifh, &info);
> > @@ -380,12 +385,9 @@ static int ocelot_port_xmit(struct sk_buff *skb,
> > struct net_device *dev)
> > dev->stats.tx_packets++;
> > dev->stats.tx_bytes += skb->len;
> >
> > - if (!ocelot_port_add_txtstamp_skb(ocelot_port, skb)) {
> > - ocelot_port->ts_id++;
> > - return NETDEV_TX_OK;
> > - }
> > + if (!do_tstamp)
> > + dev_kfree_skb_any(skb);
> >
> > - dev_kfree_skb_any(skb);
> > return NETDEV_TX_OK;
> > }
> >
> > --
> > 2.25.1
> >
>
> On 18/09/2020 04:07:24+0300, Vladimir Oltean wrote:
> > From: Vladimir Oltean <vladimir.olt...@nxp.com>
> >
> > The ocelot_port->ts_id is used to:
> > (a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
> > with an skb.
> > (b) populate the REW_OP from the injection header of the ongoing skb.
> > Only then is ocelot_port->ts_id incremented.
> >
> > This is a problem because, at least theoretically, another timestampable
> > skb might use the same ocelot_port->ts_id before that is incremented.
> > Normally all transmit calls are serialized by the netdev transmit
> > spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
> > called by DSA, which has started declaring the NETIF_F_LLTX feature
> > since commit 2b86cb829976 ("net: dsa: declare lockless TX feature for
> > slave ports"). So the logic of using and incrementing the timestamp id
> > should be atomic per port.
> >
> > The solution is to use the global ocelot_port->ts_id only while
> > protected by the associated ocelot_port->ts_id_lock. That's where we
> > populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
> > is called for the actual skb, but for felix, it is called for the skb's
> > clone. That is something which will also be changed in the future.
> >
> > Signed-off-by: Vladimir Oltean <vladimir.olt...@nxp.com>
> > Reviewed-by: Horatiu Vultur <horatiu.vul...@microchip.com>
> > ---
> > Changes in v2:
> > Added an extra explanation about NETIF_F_LLTX in commit message.
> >
> > drivers/net/ethernet/mscc/ocelot.c | 8 +++++++-
> > drivers/net/ethernet/mscc/ocelot_net.c | 6 ++----
> > include/soc/mscc/ocelot.h | 1 +
> > net/dsa/tag_ocelot.c | 11 +++++++----
> > 4 files changed, 17 insertions(+), 9 deletions(-)
> >
> > diff --git a/drivers/net/ethernet/mscc/ocelot.c
> > b/drivers/net/ethernet/mscc/ocelot.c
> > index 5abb7d2b0a9e..83eb7c325061 100644
> > --- a/drivers/net/ethernet/mscc/ocelot.c
> > +++ b/drivers/net/ethernet/mscc/ocelot.c
> > @@ -421,10 +421,15 @@ int ocelot_port_add_txtstamp_skb(struct ocelot_port
> > *ocelot_port,
> >
> > if (ocelot->ptp && shinfo->tx_flags & SKBTX_HW_TSTAMP &&
> > ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP) {
> > + spin_lock(&ocelot_port->ts_id_lock);
> > +
> > shinfo->tx_flags |= SKBTX_IN_PROGRESS;
> > /* Store timestamp ID in cb[0] of sk_buff */
> > - skb->cb[0] = ocelot_port->ts_id % 4;
> > + skb->cb[0] = ocelot_port->ts_id;
> > + ocelot_port->ts_id = (ocelot_port->ts_id + 1) % 4;
> > skb_queue_tail(&ocelot_port->tx_skbs, skb);
> > +
> > + spin_unlock(&ocelot_port->ts_id_lock);
> > return 0;
> > }
> > return -ENODATA;
> > @@ -1300,6 +1305,7 @@ void ocelot_init_port(struct ocelot *ocelot, int port)
> > struct ocelot_port *ocelot_port = ocelot->ports[port];
> >
> > skb_queue_head_init(&ocelot_port->tx_skbs);
> > + spin_lock_init(&ocelot_port->ts_id_lock);
> >
> > /* Basic L2 initialization */
> >
> > diff --git a/drivers/net/ethernet/mscc/ocelot_net.c
> > b/drivers/net/ethernet/mscc/ocelot_net.c
> > index cacabc23215a..8490e42e9e2d 100644
> > --- a/drivers/net/ethernet/mscc/ocelot_net.c
> > +++ b/drivers/net/ethernet/mscc/ocelot_net.c
> > @@ -349,10 +349,8 @@ static int ocelot_port_xmit(struct sk_buff *skb,
> > struct net_device *dev)
> >
> > if (ocelot->ptp && shinfo->tx_flags & SKBTX_HW_TSTAMP) {
> > info.rew_op = ocelot_port->ptp_cmd;
> > - if (ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP) {
> > - info.rew_op |= (ocelot_port->ts_id % 4) << 3;
> > - ocelot_port->ts_id++;
> > - }
> > + if (ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP)
> > + info.rew_op |= skb->cb[0] << 3;
> > }
> >
> > ocelot_gen_ifh(ifh, &info);
> > diff --git a/include/soc/mscc/ocelot.h b/include/soc/mscc/ocelot.h
> > index da369b12005f..4521dd602ddc 100644
> > --- a/include/soc/mscc/ocelot.h
> > +++ b/include/soc/mscc/ocelot.h
> > @@ -566,6 +566,7 @@ struct ocelot_port {
> > u8 ptp_cmd;
> > struct sk_buff_head tx_skbs;
> > u8 ts_id;
> > + spinlock_t ts_id_lock;
> >
> > phy_interface_t phy_mode;
> >
> > diff --git a/net/dsa/tag_ocelot.c b/net/dsa/tag_ocelot.c
> > index 42f327c06dca..b4fc05cafaa6 100644
> > --- a/net/dsa/tag_ocelot.c
> > +++ b/net/dsa/tag_ocelot.c
> > @@ -160,11 +160,14 @@ static struct sk_buff *ocelot_xmit(struct sk_buff
> > *skb,
> > packing(injection, &qos_class, 19, 17, OCELOT_TAG_LEN, PACK, 0);
> >
> > if (ocelot->ptp && (skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP)) {
> > + struct sk_buff *clone = DSA_SKB_CB(skb)->clone;
> > +
> > rew_op = ocelot_port->ptp_cmd;
> > - if (ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP) {
> > - rew_op |= (ocelot_port->ts_id % 4) << 3;
> > - ocelot_port->ts_id++;
> > - }
> > + /* Retrieve timestamp ID populated inside skb->cb[0] of the
> > + * clone by ocelot_port_add_txtstamp_skb
> > + */
> > + if (ocelot_port->ptp_cmd == IFH_REW_OP_TWO_STEP_PTP)
> > + rew_op |= clone->cb[0] << 3;
> >
> > packing(injection, &rew_op, 125, 117, OCELOT_TAG_LEN, PACK, 0);
> > }
> > --
> > 2.25.1
> >
>
> On 18/09/2020 04:07:25+0300, Vladimir Oltean wrote:
> > From: Vladimir Oltean <vladimir.olt...@nxp.com>
> >
> > The VSC9953 Seville switch has 2 megabits of buffer split into 4360
> > words of 60 bytes each.
> >
> > Signed-off-by: Vladimir Oltean <vladimir.olt...@nxp.com>
> > Reviewed-by: Horatiu Vultur <horatiu.vul...@microchip.com>
> > ---
> > Changes in v2:
> > None.
> >
> > drivers/net/dsa/ocelot/seville_vsc9953.c | 2 +-
> > 1 file changed, 1 insertion(+), 1 deletion(-)
> >
> > diff --git a/drivers/net/dsa/ocelot/seville_vsc9953.c
> > b/drivers/net/dsa/ocelot/seville_vsc9953.c
> > index 2d6a5f5758f8..83a1ab9393e9 100644
> > --- a/drivers/net/dsa/ocelot/seville_vsc9953.c
> > +++ b/drivers/net/dsa/ocelot/seville_vsc9953.c
> > @@ -1018,7 +1018,7 @@ static const struct felix_info seville_info_vsc9953 =
> > {
> > .vcap_is2_keys = vsc9953_vcap_is2_keys,
> > .vcap_is2_actions = vsc9953_vcap_is2_actions,
> > .vcap = vsc9953_vcap_props,
> > - .shared_queue_sz = 128 * 1024,
> > + .shared_queue_sz = 2048 * 1024,
> > .num_mact_rows = 2048,
> > .num_ports = 10,
> > .mdio_bus_alloc = vsc9953_mdio_bus_alloc,
> > --
> > 2.25.1
> >
>
> On 18/09/2020 04:07:26+0300, Vladimir Oltean wrote:
> > From: Vladimir Oltean <vladimir.olt...@nxp.com>
> >
> > Do not proceed probing if we couldn't allocate memory for the ports
> > array, just error out.
> >
> > Signed-off-by: Vladimir Oltean <vladimir.olt...@nxp.com>
> > Reviewed-by: Horatiu Vultur <horatiu.vul...@microchip.com>
> > ---
> > Changes in v2:
> > Stopped leaking the 'ports' OF node.
> >
> > drivers/net/ethernet/mscc/ocelot_vsc7514.c | 4 ++++
> > 1 file changed, 4 insertions(+)
> >
> > diff --git a/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > b/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > index 65408bc994c4..904ea299a5e8 100644
> > --- a/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > +++ b/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > @@ -993,6 +993,10 @@ static int mscc_ocelot_probe(struct platform_device
> > *pdev)
> >
> > ocelot->ports = devm_kcalloc(&pdev->dev, ocelot->num_phys_ports,
> > sizeof(struct ocelot_port *), GFP_KERNEL);
> > + if (!ocelot->ports) {
> > + err = -ENOMEM;
> > + goto out_put_ports;
> > + }
> >
> > ocelot->vcap_is2_keys = vsc7514_vcap_is2_keys;
> > ocelot->vcap_is2_actions = vsc7514_vcap_is2_actions;
> > --
> > 2.25.1
> >
>
> On 18/09/2020 04:07:27+0300, Vladimir Oltean wrote:
> > From: Vladimir Oltean <vladimir.olt...@nxp.com>
> >
> > ocelot_init() allocates memory, resets the switch and polls for a status
> > register, things which can fail. Stop probing the driver in that case,
> > and propagate the error result.
> >
> > Signed-off-by: Vladimir Oltean <vladimir.olt...@nxp.com>
> > Reviewed-by: Horatiu Vultur <horatiu.vul...@microchip.com>
> > ---
> > Changes in v2:
> > Stopped leaking the 'ports' OF node in the VSC7514 driver.
> >
> > drivers/net/dsa/ocelot/felix.c | 5 ++++-
> > drivers/net/ethernet/mscc/ocelot_vsc7514.c | 5 ++++-
> > 2 files changed, 8 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/net/dsa/ocelot/felix.c b/drivers/net/dsa/ocelot/felix.c
> > index a1e1d3824110..f7b43f8d56ed 100644
> > --- a/drivers/net/dsa/ocelot/felix.c
> > +++ b/drivers/net/dsa/ocelot/felix.c
> > @@ -571,7 +571,10 @@ static int felix_setup(struct dsa_switch *ds)
> > if (err)
> > return err;
> >
> > - ocelot_init(ocelot);
> > + err = ocelot_init(ocelot);
> > + if (err)
> > + return err;
> > +
> > if (ocelot->ptp) {
> > err = ocelot_init_timestamp(ocelot, &ocelot_ptp_clock_info);
> > if (err) {
> > diff --git a/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > b/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > index 904ea299a5e8..a1cbb20a7757 100644
> > --- a/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > +++ b/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > @@ -1002,7 +1002,10 @@ static int mscc_ocelot_probe(struct platform_device
> > *pdev)
> > ocelot->vcap_is2_actions = vsc7514_vcap_is2_actions;
> > ocelot->vcap = vsc7514_vcap_props;
> >
> > - ocelot_init(ocelot);
> > + err = ocelot_init(ocelot);
> > + if (err)
> > + goto out_put_ports;
> > +
> > if (ocelot->ptp) {
> > err = ocelot_init_timestamp(ocelot, &ocelot_ptp_clock_info);
> > if (err) {
> > --
> > 2.25.1
> >
>
> On 18/09/2020 04:07:28+0300, Vladimir Oltean wrote:
> > From: Vladimir Oltean <vladimir.olt...@nxp.com>
> >
> > mscc_ocelot_probe() is already pretty large and hard to follow. So move
> > the code for parsing ports in a separate function.
> >
> > This makes it easier for the next patch to just call
> > mscc_ocelot_release_ports from the error path of mscc_ocelot_init_ports.
> >
> > Signed-off-by: Vladimir Oltean <vladimir.olt...@nxp.com>
> > Reviewed-by: Horatiu Vultur <horatiu.vul...@microchip.com>
> > ---
> > Changes in v2:
> > Keep a reference to the 'ports' OF node at caller side, in
> > mscc_ocelot_probe, because we need to populate ocelot->num_phys_ports
> > early. The ocelot_init() function depends on it being set correctly.
> >
> > drivers/net/ethernet/mscc/ocelot_vsc7514.c | 209 +++++++++++----------
> > 1 file changed, 110 insertions(+), 99 deletions(-)
> >
> > diff --git a/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > b/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > index a1cbb20a7757..ff4a01424953 100644
> > --- a/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > +++ b/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > @@ -896,11 +896,115 @@ static struct ptp_clock_info ocelot_ptp_clock_info =
> > {
> > .enable = ocelot_ptp_enable,
> > };
> >
> > +static int mscc_ocelot_init_ports(struct platform_device *pdev,
> > + struct device_node *ports)
> > +{
> > + struct ocelot *ocelot = platform_get_drvdata(pdev);
> > + struct device_node *portnp;
> > + int err;
> > +
> > + ocelot->ports = devm_kcalloc(ocelot->dev, ocelot->num_phys_ports,
> > + sizeof(struct ocelot_port *), GFP_KERNEL);
> > + if (!ocelot->ports)
> > + return -ENOMEM;
> > +
> > + /* No NPI port */
> > + ocelot_configure_cpu(ocelot, -1, OCELOT_TAG_PREFIX_NONE,
> > + OCELOT_TAG_PREFIX_NONE);
> > +
> > + for_each_available_child_of_node(ports, portnp) {
> > + struct ocelot_port_private *priv;
> > + struct ocelot_port *ocelot_port;
> > + struct device_node *phy_node;
> > + phy_interface_t phy_mode;
> > + struct phy_device *phy;
> > + struct regmap *target;
> > + struct resource *res;
> > + struct phy *serdes;
> > + char res_name[8];
> > + u32 port;
> > +
> > + if (of_property_read_u32(portnp, "reg", &port))
> > + continue;
> > +
> > + snprintf(res_name, sizeof(res_name), "port%d", port);
> > +
> > + res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> > + res_name);
> > + target = ocelot_regmap_init(ocelot, res);
> > + if (IS_ERR(target))
> > + continue;
> > +
> > + phy_node = of_parse_phandle(portnp, "phy-handle", 0);
> > + if (!phy_node)
> > + continue;
> > +
> > + phy = of_phy_find_device(phy_node);
> > + of_node_put(phy_node);
> > + if (!phy)
> > + continue;
> > +
> > + err = ocelot_probe_port(ocelot, port, target, phy);
> > + if (err) {
> > + of_node_put(portnp);
> > + return err;
> > + }
> > +
> > + ocelot_port = ocelot->ports[port];
> > + priv = container_of(ocelot_port, struct ocelot_port_private,
> > + port);
> > +
> > + of_get_phy_mode(portnp, &phy_mode);
> > +
> > + ocelot_port->phy_mode = phy_mode;
> > +
> > + switch (ocelot_port->phy_mode) {
> > + case PHY_INTERFACE_MODE_NA:
> > + continue;
> > + case PHY_INTERFACE_MODE_SGMII:
> > + break;
> > + case PHY_INTERFACE_MODE_QSGMII:
> > + /* Ensure clock signals and speed is set on all
> > + * QSGMII links
> > + */
> > + ocelot_port_writel(ocelot_port,
> > + DEV_CLOCK_CFG_LINK_SPEED
> > + (OCELOT_SPEED_1000),
> > + DEV_CLOCK_CFG);
> > + break;
> > + default:
> > + dev_err(ocelot->dev,
> > + "invalid phy mode for port%d, (Q)SGMII only\n",
> > + port);
> > + of_node_put(portnp);
> > + return -EINVAL;
> > + }
> > +
> > + serdes = devm_of_phy_get(ocelot->dev, portnp, NULL);
> > + if (IS_ERR(serdes)) {
> > + err = PTR_ERR(serdes);
> > + if (err == -EPROBE_DEFER)
> > + dev_dbg(ocelot->dev, "deferring probe\n");
> > + else
> > + dev_err(ocelot->dev,
> > + "missing SerDes phys for port%d\n",
> > + port);
> > +
> > + of_node_put(portnp);
> > + return err;
> > + }
> > +
> > + priv->serdes = serdes;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > static int mscc_ocelot_probe(struct platform_device *pdev)
> > {
> > struct device_node *np = pdev->dev.of_node;
> > - struct device_node *ports, *portnp;
> > int err, irq_xtr, irq_ptp_rdy;
> > + struct device_node *ports;
> > struct ocelot *ocelot;
> > struct regmap *hsio;
> > unsigned int i;
> > @@ -985,19 +1089,12 @@ static int mscc_ocelot_probe(struct platform_device
> > *pdev)
> >
> > ports = of_get_child_by_name(np, "ethernet-ports");
> > if (!ports) {
> > - dev_err(&pdev->dev, "no ethernet-ports child node found\n");
> > + dev_err(ocelot->dev, "no ethernet-ports child node found\n");
> > return -ENODEV;
> > }
> >
> > ocelot->num_phys_ports = of_get_child_count(ports);
> >
> > - ocelot->ports = devm_kcalloc(&pdev->dev, ocelot->num_phys_ports,
> > - sizeof(struct ocelot_port *), GFP_KERNEL);
> > - if (!ocelot->ports) {
> > - err = -ENOMEM;
> > - goto out_put_ports;
> > - }
> > -
> > ocelot->vcap_is2_keys = vsc7514_vcap_is2_keys;
> > ocelot->vcap_is2_actions = vsc7514_vcap_is2_actions;
> > ocelot->vcap = vsc7514_vcap_props;
> > @@ -1006,6 +1103,10 @@ static int mscc_ocelot_probe(struct platform_device
> > *pdev)
> > if (err)
> > goto out_put_ports;
> >
> > + err = mscc_ocelot_init_ports(pdev, ports);
> > + if (err)
> > + goto out_put_ports;
> > +
> > if (ocelot->ptp) {
> > err = ocelot_init_timestamp(ocelot, &ocelot_ptp_clock_info);
> > if (err) {
> > @@ -1015,96 +1116,6 @@ static int mscc_ocelot_probe(struct platform_device
> > *pdev)
> > }
> > }
> >
> > - /* No NPI port */
> > - ocelot_configure_cpu(ocelot, -1, OCELOT_TAG_PREFIX_NONE,
> > - OCELOT_TAG_PREFIX_NONE);
> > -
> > - for_each_available_child_of_node(ports, portnp) {
> > - struct ocelot_port_private *priv;
> > - struct ocelot_port *ocelot_port;
> > - struct device_node *phy_node;
> > - phy_interface_t phy_mode;
> > - struct phy_device *phy;
> > - struct regmap *target;
> > - struct resource *res;
> > - struct phy *serdes;
> > - char res_name[8];
> > - u32 port;
> > -
> > - if (of_property_read_u32(portnp, "reg", &port))
> > - continue;
> > -
> > - snprintf(res_name, sizeof(res_name), "port%d", port);
> > -
> > - res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> > - res_name);
> > - target = ocelot_regmap_init(ocelot, res);
> > - if (IS_ERR(target))
> > - continue;
> > -
> > - phy_node = of_parse_phandle(portnp, "phy-handle", 0);
> > - if (!phy_node)
> > - continue;
> > -
> > - phy = of_phy_find_device(phy_node);
> > - of_node_put(phy_node);
> > - if (!phy)
> > - continue;
> > -
> > - err = ocelot_probe_port(ocelot, port, target, phy);
> > - if (err) {
> > - of_node_put(portnp);
> > - goto out_put_ports;
> > - }
> > -
> > - ocelot_port = ocelot->ports[port];
> > - priv = container_of(ocelot_port, struct ocelot_port_private,
> > - port);
> > -
> > - of_get_phy_mode(portnp, &phy_mode);
> > -
> > - ocelot_port->phy_mode = phy_mode;
> > -
> > - switch (ocelot_port->phy_mode) {
> > - case PHY_INTERFACE_MODE_NA:
> > - continue;
> > - case PHY_INTERFACE_MODE_SGMII:
> > - break;
> > - case PHY_INTERFACE_MODE_QSGMII:
> > - /* Ensure clock signals and speed is set on all
> > - * QSGMII links
> > - */
> > - ocelot_port_writel(ocelot_port,
> > - DEV_CLOCK_CFG_LINK_SPEED
> > - (OCELOT_SPEED_1000),
> > - DEV_CLOCK_CFG);
> > - break;
> > - default:
> > - dev_err(ocelot->dev,
> > - "invalid phy mode for port%d, (Q)SGMII only\n",
> > - port);
> > - of_node_put(portnp);
> > - err = -EINVAL;
> > - goto out_put_ports;
> > - }
> > -
> > - serdes = devm_of_phy_get(ocelot->dev, portnp, NULL);
> > - if (IS_ERR(serdes)) {
> > - err = PTR_ERR(serdes);
> > - if (err == -EPROBE_DEFER)
> > - dev_dbg(ocelot->dev, "deferring probe\n");
> > - else
> > - dev_err(ocelot->dev,
> > - "missing SerDes phys for port%d\n",
> > - port);
> > -
> > - of_node_put(portnp);
> > - goto out_put_ports;
> > - }
> > -
> > - priv->serdes = serdes;
> > - }
> > -
> > register_netdevice_notifier(&ocelot_netdevice_nb);
> > register_switchdev_notifier(&ocelot_switchdev_nb);
> > register_switchdev_blocking_notifier(&ocelot_switchdev_blocking_nb);
> > --
> > 2.25.1
> >
>
> On 18/09/2020 04:07:29+0300, Vladimir Oltean wrote:
> > From: Vladimir Oltean <vladimir.olt...@nxp.com>
> >
> > This driver was not unregistering its network interfaces on unbind.
> > Now it is.
> >
> > Signed-off-by: Vladimir Oltean <vladimir.olt...@nxp.com>
> > Reviewed-by: Horatiu Vultur <horatiu.vul...@microchip.com>
> > ---
> > Changes in v2:
> > No longer call mscc_ocelot_release_ports from the regular exit path of
> > mscc_ocelot_init_ports, which was incorrect.
> >
> > drivers/net/ethernet/mscc/ocelot_vsc7514.c | 21 +++++++++++++++++++++
> > 1 file changed, 21 insertions(+)
> >
> > diff --git a/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > b/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > index ff4a01424953..252c49b5f22b 100644
> > --- a/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > +++ b/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > @@ -896,6 +896,26 @@ static struct ptp_clock_info ocelot_ptp_clock_info = {
> > .enable = ocelot_ptp_enable,
> > };
> >
> > +static void mscc_ocelot_release_ports(struct ocelot *ocelot)
> > +{
> > + int port;
> > +
> > + for (port = 0; port < ocelot->num_phys_ports; port++) {
> > + struct ocelot_port_private *priv;
> > + struct ocelot_port *ocelot_port;
> > +
> > + ocelot_port = ocelot->ports[port];
> > + if (!ocelot_port)
> > + continue;
> > +
> > + priv = container_of(ocelot_port, struct ocelot_port_private,
> > + port);
> > +
> > + unregister_netdev(priv->dev);
> > + free_netdev(priv->dev);
> > + }
> > +}
> > +
> > static int mscc_ocelot_init_ports(struct platform_device *pdev,
> > struct device_node *ports)
> > {
> > @@ -1132,6 +1152,7 @@ static int mscc_ocelot_remove(struct platform_device
> > *pdev)
> > struct ocelot *ocelot = platform_get_drvdata(pdev);
> >
> > ocelot_deinit_timestamp(ocelot);
> > + mscc_ocelot_release_ports(ocelot);
> > ocelot_deinit(ocelot);
> > unregister_switchdev_blocking_notifier(&ocelot_switchdev_blocking_nb);
> > unregister_switchdev_notifier(&ocelot_switchdev_nb);
> > --
> > 2.25.1
> >
>
> On 18/09/2020 04:07:30+0300, Vladimir Oltean wrote:
> > From: Vladimir Oltean <vladimir.olt...@nxp.com>
> >
> > Currently mscc_ocelot_init_ports() will skip initializing a port when it
> > doesn't have a phy-handle, so the ocelot->ports[port] pointer will be
> > NULL. Take this into consideration when tearing down the driver, and add
> > a new function ocelot_deinit_port() to the switch library, mirror of
> > ocelot_init_port(), which needs to be called by the driver for all ports
> > it has initialized.
> >
> > Signed-off-by: Vladimir Oltean <vladimir.olt...@nxp.com>
> > ---
> > Changes in v2:
> > Patch is new.
> >
> > drivers/net/dsa/ocelot/felix.c | 3 +++
> > drivers/net/ethernet/mscc/ocelot.c | 16 ++++++++--------
> > drivers/net/ethernet/mscc/ocelot_vsc7514.c | 2 ++
> > include/soc/mscc/ocelot.h | 1 +
> > 4 files changed, 14 insertions(+), 8 deletions(-)
> >
> > diff --git a/drivers/net/dsa/ocelot/felix.c b/drivers/net/dsa/ocelot/felix.c
> > index f7b43f8d56ed..64939ee14648 100644
> > --- a/drivers/net/dsa/ocelot/felix.c
> > +++ b/drivers/net/dsa/ocelot/felix.c
> > @@ -624,10 +624,13 @@ static void felix_teardown(struct dsa_switch *ds)
> > {
> > struct ocelot *ocelot = ds->priv;
> > struct felix *felix = ocelot_to_felix(ocelot);
> > + int port;
> >
> > if (felix->info->mdio_bus_free)
> > felix->info->mdio_bus_free(ocelot);
> >
> > + for (port = 0; port < ocelot->num_phys_ports; port++)
> > + ocelot_deinit_port(ocelot, port);
> > ocelot_deinit_timestamp(ocelot);
> > /* stop workqueue thread */
> > ocelot_deinit(ocelot);
> > diff --git a/drivers/net/ethernet/mscc/ocelot.c
> > b/drivers/net/ethernet/mscc/ocelot.c
> > index 83eb7c325061..8518e1d60da4 100644
> > --- a/drivers/net/ethernet/mscc/ocelot.c
> > +++ b/drivers/net/ethernet/mscc/ocelot.c
> > @@ -1550,18 +1550,18 @@ EXPORT_SYMBOL(ocelot_init);
> >
> > void ocelot_deinit(struct ocelot *ocelot)
> > {
> > - struct ocelot_port *port;
> > - int i;
> > -
> > cancel_delayed_work(&ocelot->stats_work);
> > destroy_workqueue(ocelot->stats_queue);
> > mutex_destroy(&ocelot->stats_lock);
> > -
> > - for (i = 0; i < ocelot->num_phys_ports; i++) {
> > - port = ocelot->ports[i];
> > - skb_queue_purge(&port->tx_skbs);
> > - }
> > }
> > EXPORT_SYMBOL(ocelot_deinit);
> >
> > +void ocelot_deinit_port(struct ocelot *ocelot, int port)
> > +{
> > + struct ocelot_port *ocelot_port = ocelot->ports[port];
> > +
> > + skb_queue_purge(&ocelot_port->tx_skbs);
> > +}
> > +EXPORT_SYMBOL(ocelot_deinit_port);
> > +
> > MODULE_LICENSE("Dual MIT/GPL");
> > diff --git a/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > b/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > index 252c49b5f22b..e02fb8bfab63 100644
> > --- a/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > +++ b/drivers/net/ethernet/mscc/ocelot_vsc7514.c
> > @@ -908,6 +908,8 @@ static void mscc_ocelot_release_ports(struct ocelot
> > *ocelot)
> > if (!ocelot_port)
> > continue;
> >
> > + ocelot_deinit_port(ocelot, port);
> > +
> > priv = container_of(ocelot_port, struct ocelot_port_private,
> > port);
> >
> > diff --git a/include/soc/mscc/ocelot.h b/include/soc/mscc/ocelot.h
> > index 4521dd602ddc..0ac4e7fba086 100644
> > --- a/include/soc/mscc/ocelot.h
> > +++ b/include/soc/mscc/ocelot.h
> > @@ -678,6 +678,7 @@ void ocelot_configure_cpu(struct ocelot *ocelot, int
> > npi,
> > int ocelot_init(struct ocelot *ocelot);
> > void ocelot_deinit(struct ocelot *ocelot);
> > void ocelot_init_port(struct ocelot *ocelot, int port);
> > +void ocelot_deinit_port(struct ocelot *ocelot, int port);
> >
> > /* DSA callbacks */
> > void ocelot_port_enable(struct ocelot *ocelot, int port,
> > --
> > 2.25.1
> >
>
>
> --
> Alexandre Belloni, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com
--
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
