Rather than trying to be "smart" about possible transmit timeout
causes. Just clear all pending frames and reset the PHY.
Signed-off-by: Stephen Hemminger <[EMAIL PROTECTED]>
---
drivers/net/sky2.c | 41 +++++++++++++++--------------------------
1 file changed, 15 insertions(+), 26 deletions(-)
--- sky2-dev.orig/drivers/net/sky2.c 2007-02-06 10:44:21.000000000 -0800
+++ sky2-dev/drivers/net/sky2.c 2007-02-06 10:44:23.000000000 -0800
@@ -1840,48 +1840,37 @@
}
-/* Transmit timeout is only called if we are running, carries is up
+/* Transmit timeout is only called if we are running, carrier is up
* and tx queue is full (stopped).
+ * Called with netif_tx_lock held.
*/
static void sky2_tx_timeout(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
- unsigned txq = txqaddr[sky2->port];
- u16 report, done;
+ u32 imask;
if (netif_msg_timer(sky2))
printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
- report = sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX :
STAT_TXA2_RIDX);
- done = sky2_read16(hw, Q_ADDR(txq, Q_DONE));
-
printk(KERN_DEBUG PFX "%s: transmit ring %u .. %u report=%u done=%u\n",
- dev->name,
- sky2->tx_cons, sky2->tx_prod, report, done);
-
- if (report != done) {
- printk(KERN_INFO PFX "status burst pending (irq
moderation?)\n");
+ dev->name, sky2->tx_cons, sky2->tx_prod,
+ sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX :
STAT_TXA2_RIDX),
+ sky2_read16(hw, Q_ADDR(txqaddr[sky2->port], Q_DONE)));
- sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
- sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
- } else if (report != sky2->tx_cons) {
- printk(KERN_INFO PFX "status report lost?\n");
+ imask = sky2_read32(hw, B0_IMSK); /* block IRQ in hw */
+ sky2_write32(hw, B0_IMSK, 0);
+ sky2_read32(hw, B0_IMSK);
- netif_tx_lock_bh(dev);
- sky2_tx_complete(sky2, report);
- netif_tx_unlock_bh(dev);
- } else {
- printk(KERN_INFO PFX "hardware hung? flushing\n");
+ netif_poll_disable(hw->dev[0]); /* stop NAPI poll */
+ synchronize_irq(hw->pdev->irq);
- sky2_write32(hw, Q_ADDR(txq, Q_CSR), BMU_STOP);
- sky2_write32(hw, Y2_QADDR(txq, PREF_UNIT_CTRL),
PREF_UNIT_RST_SET);
+ netif_start_queue(dev); /* don't wakeup during flush */
+ sky2_tx_complete(sky2, sky2->tx_prod); /* Flush transmit queue */
- sky2_tx_clean(dev);
+ sky2_write32(hw, B0_IMSK, imask);
- sky2_qset(hw, txq);
- sky2_prefetch_init(hw, txq, sky2->tx_le_map, TX_RING_SIZE - 1);
- }
+ sky2_phy_reinit(sky2); /* this clears flow control etc
*/
}
static int sky2_change_mtu(struct net_device *dev, int new_mtu)
--
Stephen Hemminger <[EMAIL PROTECTED]>
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
