> +static int ionic_get_link_ksettings(struct net_device *netdev,
> + struct ethtool_link_ksettings *ks)
> +{
> + struct lif *lif = netdev_priv(netdev);
> + struct ionic_dev *idev = &lif->ionic->idev;
> + int copper_seen = 0;
> +
> + ethtool_link_ksettings_zero_link_mode(ks, supported);
> + ethtool_link_ksettings_zero_link_mode(ks, advertising);
> +
> + switch (le16_to_cpu(idev->port_info->status.xcvr.pid)) {
> + /* Copper */
> + case XCVR_PID_QSFP_100G_CR4:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 100000baseCR4_Full);
> + copper_seen++;
> + break;
> + case XCVR_PID_QSFP_40GBASE_CR4:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 40000baseCR4_Full);
> + copper_seen++;
> + break;
> + case XCVR_PID_SFP_25GBASE_CR_S:
> + case XCVR_PID_SFP_25GBASE_CR_L:
> + case XCVR_PID_SFP_25GBASE_CR_N:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 25000baseCR_Full);
> + copper_seen++;
> + break;
> + case XCVR_PID_SFP_10GBASE_AOC:
> + case XCVR_PID_SFP_10GBASE_CU:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 10000baseCR_Full);
> + copper_seen++;
> + break;
> +
> + /* Fibre */
> + case XCVR_PID_QSFP_100G_SR4:
> + case XCVR_PID_QSFP_100G_AOC:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 100000baseSR4_Full);
> + break;
> + case XCVR_PID_QSFP_100G_LR4:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 100000baseLR4_ER4_Full);
> + break;
> + case XCVR_PID_QSFP_100G_ER4:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 100000baseLR4_ER4_Full);
> + break;
> + case XCVR_PID_QSFP_40GBASE_SR4:
> + case XCVR_PID_QSFP_40GBASE_AOC:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 40000baseSR4_Full);
> + break;
> + case XCVR_PID_QSFP_40GBASE_LR4:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 40000baseLR4_Full);
> + break;
> + case XCVR_PID_SFP_25GBASE_SR:
> + case XCVR_PID_SFP_25GBASE_AOC:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 25000baseSR_Full);
> + break;
> + case XCVR_PID_SFP_10GBASE_SR:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 10000baseSR_Full);
> + break;
> + case XCVR_PID_SFP_10GBASE_LR:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 10000baseLR_Full);
> + break;
> + case XCVR_PID_SFP_10GBASE_LRM:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 10000baseLRM_Full);
> + break;
> + case XCVR_PID_SFP_10GBASE_ER:
> + ethtool_link_ksettings_add_link_mode(ks, supported,
> + 10000baseER_Full);
> + break;
I don't know these link modes too well. But only setting a single bit
seems odd. What i do know is that an SFP which supports 2500BaseX
should also be able to support 1000BaseX. So should a 100G SFP also
support 40G, 25G, 10G etc? The SERDES just runs a slower bitstream
over the basic bitpipe?
> + case XCVR_PID_QSFP_100G_ACC:
> + case XCVR_PID_QSFP_40GBASE_ER4:
> + case XCVR_PID_SFP_25GBASE_LR:
> + case XCVR_PID_SFP_25GBASE_ER:
> + dev_info(lif->ionic->dev, "no decode bits for xcvr type pid=%d
> / 0x%x\n",
> + idev->port_info->status.xcvr.pid,
> + idev->port_info->status.xcvr.pid);
> + break;
Why not add them?
> + memcpy(ks->link_modes.advertising, ks->link_modes.supported,
> + sizeof(ks->link_modes.advertising));
bitmap_copy() would be a better way to do this. You could consider
adding a helper to ethtool.h.
Andrew
