On 13-02-19, 09:02, Peter Ujfalusi wrote:
> Hi Vinod,
>
> On 12/02/2019 16.19, Vinod Koul wrote:
> > Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode
> > should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID
> > can have delay in phy.
> >
> > So disable the delay only for RGMII mode and disable for other modes
> s/disable for other modes/enable for other modes
oops
>
> Works fine on am335x-evmsk:
> Tested-by: Peter Ujfalusi <peter.ujfal...@ti.com>
Thanks for quick testing..
>
> and few comment
>
> > Fixes: cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode")
> > Reported-by: Peter Ujfalusi <peter.ujfal...@ti.com>
> > Signed-off-by: Vinod Koul <vk...@kernel.org>
> > ---
> > drivers/net/phy/at803x.c | 33 ++++++++++++++++++++++++++-------
> > 1 file changed, 26 insertions(+), 7 deletions(-)
> >
> > diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
> > index 8ff12938ab47..7b54b54e3316 100644
> > --- a/drivers/net/phy/at803x.c
> > +++ b/drivers/net/phy/at803x.c
> > @@ -110,6 +110,18 @@ static int at803x_debug_reg_mask(struct phy_device
> > *phydev, u16 reg,
> > return phy_write(phydev, AT803X_DEBUG_DATA, val);
> > }
> >
> > +static inline int at803x_enable_rx_delay(struct phy_device *phydev)
> > +{
> > + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
> > + AT803X_DEBUG_RX_CLK_DLY_EN);
> > +}
>
> static inline int at803x_select_rx_delay(struct phy_device *phydev,
> bool enable)
> {
> }
>
> > +
> > +static inline int at803x_enable_tx_delay(struct phy_device *phydev)
> > +{
> > + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
> > + AT803X_DEBUG_TX_CLK_DLY_EN);
> > +}
>
> static inline int at803x_select_tx_delay(struct phy_device *phydev,
> bool enable)
> {
> }
>
> perhaps?
Given that we would again branch off on enable, I see this as no better
case so I will keep existing
>
> > +
> > static inline int at803x_disable_rx_delay(struct phy_device *phydev)
> > {
> > return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
> > @@ -255,18 +267,25 @@ static int at803x_config_init(struct phy_device
> > *phydev)
> > if (ret < 0)
> > return ret;
> >
> > - if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
> > - phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
> > - phydev->interface == PHY_INTERFACE_MODE_RGMII) {
> > + if (phydev->interface == PHY_INTERFACE_MODE_RGMII) {
> > ret = at803x_disable_rx_delay(phydev);
> > if (ret < 0)
> > return ret;
> > + ret = at803x_disable_tx_delay(phydev);
> > + if (ret < 0)
> > + return ret;
>
> is it a possibility to have PHY_INTERFACE_MODE_RGMII and other RGMII_ID
> || RGMII_TXID || RGMII_RXID set at the same time?
Nope that would not make sense
> if not you can just return from here, no need to check for other RGMII
> modes?
for RGMII yes indeed..
--
~Vinod
