On Mon, Jan 21, 2019 at 1:20 PM <[email protected]> wrote:
>
> From: Tonghao Zhang <[email protected]>
>
> When we offload tc filters to hardware, hardware flows can
> be updated when mac of encap destination ip is changed.
> But we ignore one case, that the mac of local encap ip can
> be changed too, so we should also update them.
>
> To fix it, add route_dev in mlx5e_encap_entry struct to save
> the local encap netdevice, and when mac changed, kernel will
> flush all the neighbour on the netdevice and send NETEVENT_NEIGH_UPDATE
> event. The mlx5 driver will delete the flows and add them when neighbour
> available again.
>
> Fixes: 232c001398ae ("net/mlx5e: Add support to neighbour update flow")
> Cc: Hadar Hen Zion <[email protected]>
> Signed-off-by: Tonghao Zhang <[email protected]>
> ---
> drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun.c | 1 +
> drivers/net/ethernet/mellanox/mlx5/core/en_rep.c | 4 ++++
> drivers/net/ethernet/mellanox/mlx5/core/en_rep.h | 1 +
> 3 files changed, 6 insertions(+)
>
> diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun.c
> b/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun.c
> index 046948e..156b2b3 100644
> --- a/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun.c
> +++ b/drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun.c
> @@ -256,6 +256,7 @@ int mlx5e_tc_tun_create_header_ipv4(struct mlx5e_priv
> *priv,
please address the ipv6 tunnel path as well
> e->m_neigh.family = n->ops->family;
> memcpy(&e->m_neigh.dst_ip, n->primary_key, n->tbl->key_len);
> e->out_dev = out_dev;
> + e->route_dev = route_dev;
>
> /* It's important to add the neigh to the hash table before checking
> * the neigh validity state. So if we'll get a notification, in case
> the
> diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
> b/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
> index 96cc0c6..c4b9073 100644
> --- a/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
> +++ b/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
> @@ -594,6 +594,10 @@ static void mlx5e_rep_update_flows(struct mlx5e_priv
> *priv,
> if (neigh_connected && !(e->flags & MLX5_ENCAP_ENTRY_VALID)) {
> ether_addr_copy(e->h_dest, ha);
> ether_addr_copy(eth->h_dest, ha);
> + /* Update the encap source mac, in case that we delete
> + * the flows when encap source mac changed.
> + */
> + ether_addr_copy(eth->h_source, e->route_dev->dev_addr);
there's must be some other location in the code which currently sets
the source mac. I need to look deeper but I suspect it has to be removed
and only the one you added should stay
