Add code to detect and connect to PHY. The internal PHY of the SMSC95xx
is a regular SMSC LAN8700 and the driver only supports the internal PHY,
so just use the SMSC PHY driver to configure the PHY. Note that the
driver does a lot of extra configuration of the PHY, which is left in
to avoid breakage. Some of the extra configuration is sorted out by
later patches in this series.
Signed-off-by: Marek Vasut <ma...@denx.de>
Cc: David S. Miller <da...@davemloft.net>
Cc: Nisar Sayed <nisar.sa...@microchip.com>
Cc: Woojung Huh <woojung....@microchip.com>
Cc: Andrew Lunn <and...@lunn.ch>
Cc: Florian Fainelli <f.faine...@gmail.com>
Cc: linux-...@vger.kernel.org
To: netdev@vger.kernel.org
---
drivers/net/usb/smsc95xx.c | 29 +++++++++++++++++++++++++++--
1 file changed, 27 insertions(+), 2 deletions(-)
diff --git a/drivers/net/usb/smsc95xx.c b/drivers/net/usb/smsc95xx.c
index 2cd5e1d34559..ce61be8ee32b 100644
--- a/drivers/net/usb/smsc95xx.c
+++ b/drivers/net/usb/smsc95xx.c
@@ -78,6 +78,7 @@ struct smsc95xx_priv {
struct delayed_work carrier_check;
struct usbnet *dev;
struct mii_bus *mii_bus;
+ struct phy_device *phydev;
};
static bool turbo_mode = true;
@@ -960,6 +961,11 @@ static int smsc95xx_start_rx_path(struct usbnet *dev)
return smsc95xx_write_reg(dev, MAC_CR, pdata->mac_cr);
}
+
+static void smsc95xx_adjust_link(struct net_device *netdev)
+{
+}
+
static int smsc95xx_phy_initialize(struct usbnet *dev)
{
int bmcr, ret, timeout = 0;
@@ -1308,6 +1314,10 @@ static int smsc95xx_bind(struct usbnet *dev, struct
usb_interface *intf)
if (ret)
goto err_mdiobus_alloc;
+ ret = mdiobus_register(bus);
+ if (ret)
+ goto err_mdiobus_register;
+
/* Initialize MII structure */
dev->mii.dev = dev->net;
dev->mii.mdio_read = smsc95xx_mdio_read;
@@ -1316,9 +1326,24 @@ static int smsc95xx_bind(struct usbnet *dev, struct
usb_interface *intf)
dev->mii.reg_num_mask = 0x1f;
dev->mii.phy_id = SMSC95XX_INTERNAL_PHY_ID;
- ret = mdiobus_register(bus);
- if (ret)
+ /* Connect to PHY */
+ pdata->phydev = phy_find_first(pdata->mii_bus);
+ if (!pdata->phydev) {
+ netdev_err(dev->net, "no PHY found\n");
+ ret = -EIO;
goto err_mdiobus_register;
+ }
+
+ ret = phy_connect_direct(dev->net, pdata->phydev,
+ &smsc95xx_adjust_link,
+ PHY_INTERFACE_MODE_MII);
+ if (ret) {
+ netdev_err(dev->net, "Could not connect to PHY device\n");
+ goto err_mdiobus_register;
+ }
+
+ genphy_resume(pdata->phydev);
+ phy_start(pdata->phydev);
ret = smsc95xx_reset_post(dev);
if (ret)
--
2.19.2
