Hello Andrew, You deserve a big thank you for your solution to our device-tree - the linux bootup log looks a lot better and It made a big progress for us. Though we still have some issues...
1. Attached are 2 log files that are the result of your suggested dts: 1st is your device-tree as is : results in kernel panic. Its probably caused by the "link" parameter. 2nd is your device tree with gem0 port's10 "link" parameter commented on both switches. It results in good kernel but still the devices are not properly detected. Maybe its related to the comment you wrote below about the fixed PHY driver issue that prevents the driver to complete his phy address scan (stops at phy addr 1...). 2. The switch's product number should be 0x0a1 but instead its 0xa10 (is it just a high-low byte thing?) 3. The stand-alone phy (gem1) is not detected properly. It should be device id mv88e1510. Please advise how to continue from here. Regards, Michael Alayev -----Original Message----- From: Dror Alon Sent: Sunday, March 18, 2018 8:16 AM To: Alayev Michael Subject: FW: DTS for our Configuration -----Original Message----- From: Andrew Lunn [mailto:and...@lunn.ch] Sent: Friday, March 16, 2018 5:12 PM To: Dror Alon Cc: 'netdev@vger.kernel.org'; Efter Yoram; Alayev Michael Subject: Re: DTS for our Configuration On Thu, Mar 15, 2018 at 02:00:00PM +0000, Dror Alon wrote: > Hello Andrew, > Thanks for your fast responses. > Michael and I keep trying to configure our linux Zynq7000 board. > We can't succeed with configure our SWITCHES via the DTS file. > Please. See the next diagram, and please Do you have any DTS Sample > for this Setup ? Hi Dror I'm surprised you are doing SGMII between ports 10. They are 10G capable. gem0: { fixed-link { speed = <1000>; full-duplex; }; phy0: phy@0: { reg = <0>; }; switch0: switch@1c: { compatible = "marvell,mv88e6190"; reg = <0x1c>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; label = "cpu"; fixed-link { speed = <1000>; full-duplex; }; port@1 { reg = <1>; label = "lan0"; }; port@2 { reg = <2>; label = "lan1"; }; ... switch0port10: port@10 { reg = <10>; label = "dsa"; link = <&switch1port10>; phy-mode = "sgmii"; fixed-link { speed = <1000>; full-duplex; }; }; }; }; switch1: switch@1d: { compatible = "marvell,mv88e6190"; reg = <0x1d>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; label = "lan9"; }; port@1 { reg = <1>; label = "lan10"; }; port@2 { reg = <2>; label = "lan11"; }; ... switch1port10: port@10 { reg = <10>; label = "dsa"; link = <&switch0port10>; phy-mode = "sgmii"; fixed-link { speed = <1000>; full-duplex; }; }; }; }; }; gem1: { phy-handle = <phy0>; }; It looks like you have at last one issue to solve in the macb driver. If you have a fixed-phy, it does an mdiobus_register. This means it is going to ignore all the other device tree properties. You need it to do an of_mdiobus_register(). Andrew Default Profile *********************************************************************************************** Please consider the environment before printing this email ! The information contained in this communication is proprietary to Israel Aerospace Industries Ltd. and/or third parties, may contain confidential or privileged information, and is intended only for the use of the intended addressee thereof. If you are not the intended addressee, please be aware that any use, disclosure, distribution and/or copying of this communication is strictly prohibited. If you receive this communication in error, please notify the sender immediately and delete it from your computer. Thank you. Visit us at: www.iai.co.il
Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 4.14.0-xilinx (84alav@fedora64) (gcc version 5.4.0 (Buildroot 2017.05.1)) #15 SMP PREEMPT Mon Mar 19 12:30:34 IST 2018 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: Zynq Zed Development Board Memory policy: Data cache writealloc cma: Reserved 16 MiB at 0x1dc00000 percpu: Embedded 16 pages/cpu @dfbc5000 s34764 r8192 d22580 u65536 Built 1 zonelists, mobility grouping on. Total pages: 130048 Kernel command line: PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 490488K/524288K available (5120K kernel code, 224K rwdata, 1404K rodata, 1024K init, 150K bss, 17416K reserved, 16384K cma-reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0600000 (6112 kB) .init : 0xc0800000 - 0xc0900000 (1024 kB) .data : 0xc0900000 - 0xc0938000 ( 224 kB) .bss : 0xc0938000 - 0xc095da14 ( 151 kB) Preemptible hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Tasks RCU enabled. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to e0800000 slcr mapped to e0802000 L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 zynq_clock_init: clkc starts at e0802100 Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at e080a000, irq=17 Console: colour dummy device 80x30 console [tty0] enabled Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized random: get_random_u32 called from bucket_table_alloc+0x1c4/0x224 with crng_init=0 VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 random: fast init done DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor menu hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xe0840000 zynq-pinctrl 700.pinctrl: zynq pinctrl initialized e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 25, base_baud = 6249999) is a xuartps console [ttyPS0] enabled vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giome...@linux.it> PTP clock support registered EDAC MC: Ver: 3.0.0 FPGA manager framework clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... Freeing initrd memory: 3604K hw perfevents: no interrupt-affinity property for /pmu, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available workingset: timestamp_bits=30 max_order=17 bucket_order=0 jffs2: version 2.2. (NAND) (SUMMARY) ?© 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) io scheduler mq-deadline registered io scheduler kyber registered dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded libphy: Fixed MDIO Bus: probed CAN device driver interface mv88e6xxx_init kelev libphy: MACB_mii_bus: probed mdio_bus e000b000.ethernet-ffffffff: /amba/ethernet@e000b000/fixed-link has invalid PHY address mv88e6085 e000b000.ethernet-ffffffff:1d: switch 0xa10 detected: Marvell 88E6390X, revision 1 libphy: mv88e6xxx SMI: probed mv88e6085 e000b000.ethernet-ffffffff:1c: switch 0xa10 detected: Marvell 88E6390X, revision 1 libphy: mv88e6xxx SMI: probed mv88e6085: probe of e000b000.ethernet-ffffffff:1c failed with error -16 mdio_bus e000b000.ethernet-ffffffff: scan phy fixed-link at address 1 Unable to handle kernel NULL pointer dereference at virtual address 00000004 pgd = c0004000 [00000004] *pgd=00000000 Internal error: Oops - BUG: 17 [#1] PREEMPT SMP ARM Modules linked in: CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.14.0-xilinx #15 Hardware name: Xilinx Zynq Platform task: df43b840 task.stack: df43c000 PC is at dsa_unregister_switch+0x10/0x48 LR is at dsa_unregister_switch+0x10/0x48 pc : [<c05aad48>] lr : [<c05aad48>] psr: 60000013 sp : df43dd58 ip : 00000000 fp : 00000000 r10: 00000000 r9 : dd009c78 r8 : 00000034 r7 : dd0d1434 r6 : c091dd68 r5 : 00000000 r4 : dd0d1210 r3 : df43b840 r2 : 00000000 r1 : 00000000 r0 : c0936cdc Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 18c5387d Table: 1f65c04a DAC: 00000051 Process swapper/0 (pid: 1, stack limit = 0xdf43c210) Stack: (0xdf43dd58 to 0xdf43e000) dd40: dd0d1210 00000000 dd60: c091dd68 c0418ac0 dd0d1400 00000000 c091dd68 c04127ac dd0d1400 c03b72b8 dd80: dd0d1400 df4ff530 c091c448 dd0d1460 dfbeb3c4 c03b6420 dd0d1400 dd0d145c dda0: dd009c78 c03b3acc dd009e8c a0000013 dd1d2800 dd009e80 dd009e8c dd0d1400 ddc0: dd0d1400 dd009e84 dd009e8c c0412868 dd009c00 c0412624 ffffffed 00000001 dde0: dd009c00 dfbeb67c dfbeb3c4 c04bafac 00000000 c04b378c dfbecb5c 0000001c de00: c06ffa6d df77f000 df77c000 df77c4c0 dfbeb3c4 df524a10 00000000 c0423104 de20: ffffffff df43de5c 00000001 c0229cd4 dfbeb3c4 c0421054 00000001 00000002 de40: 00000001 00000001 dd1c8898 dd1c9cc0 dd1c9c40 dd1c9bc0 00000000 00000000 de60: 00000001 00000001 c091ddc8 c0422974 df524a10 c091ddc8 00000000 00000000 de80: c091ddc8 00000000 00000000 c03b84d4 df524a10 c09523dc c09523e0 c03b6e84 dea0: df524a10 df524a44 c091ddc8 c0918a28 00000000 c0938000 c083383c c03b7080 dec0: 00000000 c091ddc8 c03b7000 c03b5790 df472f58 df4edb34 c091ddc8 00000000 dee0: dd1c5300 c03b64f8 c06ff8d2 c06ff8d3 00000000 c091ddc8 c081aea4 000000a8 df00: c083be5c c03b7808 00000006 c081aea4 000000a8 c0101900 00000000 df43df24 df20: 00000000 00000000 00000000 c075d548 000000a8 00000006 00000006 00000000 df40: cccccccd 00000000 00000000 c0938000 c083383c 00000006 c0833830 000000a8 df60: 00000006 c0833834 000000a8 c083be5c c0938000 c0800d40 00000006 00000006 df80: 00000000 c0800594 00000000 c05e1e64 00000000 00000000 00000000 00000000 dfa0: 00000000 c05e1e6c 00000000 c0106fd0 00000000 00000000 00000000 00000000 dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [<c05aad48>] (dsa_unregister_switch) from [<c0418ac0>] (mv88e6xxx_remove+0x1c/0x68) [<c0418ac0>] (mv88e6xxx_remove) from [<c04127ac>] (mdio_remove+0x18/0x28) [<c04127ac>] (mdio_remove) from [<c03b72b8>] (device_release_driver_internal+0x128/0x1d0) [<c03b72b8>] (device_release_driver_internal) from [<c03b6420>] (bus_remove_device+0xcc/0xdc) [<c03b6420>] (bus_remove_device) from [<c03b3acc>] (device_del+0x1bc/0x258) [<c03b3acc>] (device_del) from [<c0412868>] (mdio_device_remove+0xc/0x18) [<c0412868>] (mdio_device_remove) from [<c0412624>] (mdiobus_unregister+0x40/0x74) [<c0412624>] (mdiobus_unregister) from [<c04bafac>] (of_mdiobus_register+0x234/0x254) [<c04bafac>] (of_mdiobus_register) from [<c0423104>] (macb_probe+0x790/0xb88) [<c0423104>] (macb_probe) from [<c03b84d4>] (platform_drv_probe+0x50/0xa0) [<c03b84d4>] (platform_drv_probe) from [<c03b6e84>] (driver_probe_device+0x13c/0x2b8) [<c03b6e84>] (driver_probe_device) from [<c03b7080>] (__driver_attach+0x80/0xa4) [<c03b7080>] (__driver_attach) from [<c03b5790>] (bus_for_each_dev+0x68/0x8c) [<c03b5790>] (bus_for_each_dev) from [<c03b64f8>] (bus_add_driver+0xc8/0x1dc) [<c03b64f8>] (bus_add_driver) from [<c03b7808>] (driver_register+0x9c/0xe0) [<c03b7808>] (driver_register) from [<c0101900>] (do_one_initcall+0xa8/0x11c) [<c0101900>] (do_one_initcall) from [<c0800d40>] (kernel_init_freeable+0x10c/0x1cc) [<c0800d40>] (kernel_init_freeable) from [<c05e1e6c>] (kernel_init+0x8/0x10c) [<c05e1e6c>] (kernel_init) from [<c0106fd0>] (ret_from_fork+0x14/0x24) Code: e92d4070 e1a05000 e59f0034 eb00ea7e (e5954004) ---[ end trace f6d20ab8f9ad8edb ]--- Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b CPU0: stopping CPU: 0 PID: 0 Comm: swapper/0 Tainted: G D 4.14.0-xilinx #15 Hardware name: Xilinx Zynq Platform [<c010e7b4>] (unwind_backtrace) from [<c010a9b0>] (show_stack+0x10/0x14) [<c010a9b0>] (show_stack) from [<c05d1950>] (dump_stack+0x80/0xa0) [<c05d1950>] (dump_stack) from [<c010cf20>] (ipi_cpu_stop+0x3c/0x70) [<c010cf20>] (ipi_cpu_stop) from [<c010d720>] (handle_IPI+0x64/0x84) [<c010d720>] (handle_IPI) from [<c01013f8>] (gic_handle_irq+0x7c/0x98) [<c01013f8>] (gic_handle_irq) from [<c010b40c>] (__irq_svc+0x6c/0xa8) Exception stack(0xc0901f48 to 0xc0901f90) 1f40: 00000001 00000000 00000000 c0116800 00000000 00000000 1f60: c0900000 c08441f8 c0901fa0 c0833a30 00000000 00000000 1f388000 c0901f98 1f80: c01079e0 c01079e4 60000013 ffffffff [<c010b40c>] (__irq_svc) from [<c01079e4>] (arch_cpu_idle+0x2c/0x38) [<c01079e4>] (arch_cpu_idle) from [<c01490fc>] (do_idle+0xd0/0x198) [<c01490fc>] (do_idle) from [<c01492fc>] (cpu_startup_entry+0x18/0x1c) [<c01492fc>] (cpu_startup_entry) from [<c0800bd4>] (start_kernel+0x308/0x368) [<c0800bd4>] (start_kernel) from [<0000807c>] (0x807c) ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 4.14.0-xilinx (84alav@fedora64) (gcc version 5.4.0 (Buildroot 2017.05.1)) #15 SMP PREEMPT Mon Mar 19 12:30:34 IST 2018 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: Zynq Zed Development Board Memory policy: Data cache writealloc cma: Reserved 16 MiB at 0x1dc00000 percpu: Embedded 16 pages/cpu @dfbc5000 s34764 r8192 d22580 u65536 Built 1 zonelists, mobility grouping on. Total pages: 130048 Kernel command line: PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 490488K/524288K available (5120K kernel code, 224K rwdata, 1404K rodata, 1024K init, 150K bss, 17416K reserved, 16384K cma-reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0600000 (6112 kB) .init : 0xc0800000 - 0xc0900000 (1024 kB) .data : 0xc0900000 - 0xc0938000 ( 224 kB) .bss : 0xc0938000 - 0xc095da14 ( 151 kB) Preemptible hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. Tasks RCU enabled. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 efuse mapped to e0800000 slcr mapped to e0802000 L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 zynq_clock_init: clkc starts at e0802100 Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at e080a000, irq=17 Console: colour dummy device 80x30 console [tty0] enabled Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100060 Hierarchical SRCU implementation. smp: Bringing up secondary CPUs ... CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 smp: Brought up 1 node, 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized random: get_random_u32 called from bucket_table_alloc+0x1c4/0x224 with crng_init=0 VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 random: fast init done DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor menu hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xe0840000 zynq-pinctrl 700.pinctrl: zynq pinctrl initialized e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 25, base_baud = 6249999) is a xuartps console [ttyPS0] enabled vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giome...@linux.it> PTP clock support registered EDAC MC: Ver: 3.0.0 FPGA manager framework clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... Freeing initrd memory: 3604K hw perfevents: no interrupt-affinity property for /pmu, guessing. hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available workingset: timestamp_bits=30 max_order=17 bucket_order=0 jffs2: version 2.2. (NAND) (SUMMARY) ?© 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) io scheduler mq-deadline registered io scheduler kyber registered dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 brd: module loaded loop: module loaded libphy: Fixed MDIO Bus: probed CAN device driver interface mv88e6xxx_init kelev libphy: MACB_mii_bus: probed mdio_bus e000b000.ethernet-ffffffff: /amba/ethernet@e000b000/fixed-link has invalid PHY address mv88e6085 e000b000.ethernet-ffffffff:1d: switch 0xa10 detected: Marvell 88E6390X, revision 1 libphy: mv88e6xxx SMI: probed DSA: switch 0 0 parsed Tree has no master device mv88e6085: probe of e000b000.ethernet-ffffffff:1d failed with error -22 mv88e6085 e000b000.ethernet-ffffffff:1c: switch 0xa10 detected: Marvell 88E6390X, revision 1 libphy: mv88e6xxx SMI: probed DSA: switch 0 0 parsed Tree has no master device mv88e6085: probe of e000b000.ethernet-ffffffff:1c failed with error -22 mdio_bus e000b000.ethernet-ffffffff: scan phy fixed-link at address 1 macb e000c000.ethernet: invalid hw address, using random libphy: MACB_mii_bus: probed macb: macb_mii_probe kelev macb e000c000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000c000 irq 28 (5e:89:7b:36:e5:d6) Generic PHY e000c000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000c000.ethernet-ffffffff:00, irq=POLL) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver usbcore: registered new interface driver usb-storage chipidea-usb2 e0002000.usb: e0002000.usb supply vbus not found, using dummy regulator ci_hdrc ci_hdrc.0: unable to init phy: -110 ci_hdrc: probe of ci_hdrc.0 failed with error -110 i2c /dev entries driver cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer at e0948000 with timeout 10s EDAC MC: ECC not enabled Xilinx Zynq CpuIdle Driver started sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on e0100000.sdhci [e0100000.sdhci] using ADMA usbcore: registered new interface driver usbhid usbhid: USB HID core driver fpga_manager fpga0: Xilinx Zynq FPGA Manager registered NET: Registered protocol family 10 Segment Routing with IPv6 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered protocol family 17 can: controller area network core (rev 20170425 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20170425) can: broadcast manager protocol (rev 20170425 t) can: netlink gateway (rev 20170425) max_hops=1 Registering SWP/SWPB emulation handler hctosys: unable to open rtc device (rtc0) of_cfs_init of_cfs_init: OK Freeing unused kernel memory: 1024K /bin/mount: special device /dev/mmcblk0p1 does not exist /bin/mount: special device /dev/mmcblk0p2 does not exist /bin/mount: special device /dev/mmcblk0p3 does not exist Starting logging: OK Initializing random number generator... done. Starting network: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready OK Starting openntpd: creating new /var/db/ntpd.drift OK Starting dropbear sshd: OK Starting vsftpd: OK
zynq-zed.dts
Description: zynq-zed.dts