With the 2.6.17 Patchs :
xfport /usr/src/linux # insmod drivers/net/r8169.ko
xfport /usr/src/linux # dmesg | tail
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: RTL8168b/8111b at 0xf0fe6000, 00:17:31:c1:8d:ee, IRQ 16
r8169: eth0: link down
r8169: eth0: link down
r8169: eth0: link up
xfport /usr/src/linux # ifconfig eth0 up
xfport /usr/src/linux # ifconfig eth0 192.168.0.20
xfport /usr/src/linux # mii-tool eth0
SIOCGMIIPHY on 'eth0' failed: Operation not supported
xfport /usr/src/linux # ping 192.168.0.2
PING 192.168.0.2 (192.168.0.2) 56(84) bytes of data.
--- 192.168.0.2 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 999ms
xfport /usr/src/linux # ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000033 (51)
Link detected: yes
With NET_IP_ALIGN + 6 : It does *exactly* the same thing, *but* it works
perfectly !!!
So I now use that, but I test 2.6.18 patchs.
With the 2.6.18 kernel patchs :
same thing as before but mii-tool works (i think i forget patchs 10 and 11
last time, sry).
BUT: i can't ping .. maybe it's just because I don't use mii-tool in the right
way :(
(patch, make, insmod, ifconfig, exactly like before)
xfport /usr/src/linux # mii-tool eth0
eth0: negotiated 100baseTx-FD flow-control, link ok
xfport /usr/src/linux # mii-diag
Using the default interface 'eth0'.
Basic registers of MII PHY #32: 1000 796d 001c c912 0de1 45e1 0005 2001.
The autonegotiated capability is 01e0.
The autonegotiated media type is 100baseTx-FD.
Basic mode control register 0x1000: Auto-negotiation enabled.
You have link beat, and everything is working OK.
Your link partner advertised 45e1: Flow-control 100baseTx-FD 100baseTx
10baseT-FD 10baseT, w/ 802.3X flow control.
End of basic transceiver information.
xfport /usr/src/linux # ping 192.168.0.2
PING 192.168.0.2 (192.168.0.2) 56(84) bytes of data.
--- 192.168.0.2 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms
--
CHARY 'Iksaif' Corentin
[EMAIL PROTECTED] - [EMAIL PROTECTED]
http://xf.iksaif.net
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
