Yixun Lan <yixun....@amlogic.com> writes:

> Add DT info for the stmmac ethernet MAC which found in
> the Amlogic's Meson-AXG SoC, also describe the ethernet
> pinctrl & clock information here.
>
> Reviewed-by: Neil Armstrong <narmstr...@baylibre.com>
> Signed-off-by: Yixun Lan <yixun....@amlogic.com>

This patch does not apply, and dependencies are not described.

> ---
>  arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 54 
> ++++++++++++++++++++++++++++++
>  1 file changed, 54 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi 
> b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> index d356ce74ad89..94c4972222b7 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> @@ -7,6 +7,7 @@
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/axg-clkc.h>
>  
>  / {
>       compatible = "amlogic,meson-axg";
> @@ -148,6 +149,19 @@
>                       #address-cells = <0>;
>               };
>  
> +             ethmac: ethernet@ff3f0000 {
> +                     compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
> +                     reg = <0x0 0xff3f0000 0x0 0x10000
> +                             0x0 0xff634540 0x0 0x8>;
> +                     interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
> +                     interrupt-names = "macirq";
> +                     clocks = <&clkc CLKID_ETH>,
> +                              <&clkc CLKID_FCLK_DIV2>,
> +                              <&clkc CLKID_MPLL2>;
> +                     clock-names = "stmmaceth", "clkin0", "clkin1";
> +                     status = "disabled";
> +             };
> +
>               hiubus: bus@ff63c000 {
>                       compatible = "simple-bus";
>                       reg = <0x0 0xff63c000 0x0 0x1c00>;

Based on the hiubus node, presumably this depends on the patch from the
clock series.

> @@ -194,6 +208,46 @@
>                                       #gpio-cells = <2>;
>                                       gpio-ranges = <&pinctrl_periphs 0 0 86>;
>                               };

I'm not sure where this part is coming from, but it causes the rest of
it to not apply.

Please be sure to describe all dependencies.

Kevin

> +
> +                             eth_rgmii_x_pins: eth-x-rgmii {
> +                                     mux {
> +                                             groups = "eth_mdio_x",
> +                                                    "eth_mdc_x",
> +                                                    "eth_rgmii_rx_clk_x",
> +                                                    "eth_rx_dv_x",
> +                                                    "eth_rxd0_x",
> +                                                    "eth_rxd1_x",
> +                                                    "eth_rxd2_rgmii",
> +                                                    "eth_rxd3_rgmii",
> +                                                    "eth_rgmii_tx_clk",
> +                                                    "eth_txen_x",
> +                                                    "eth_txd0_x",
> +                                                    "eth_txd1_x",
> +                                                    "eth_txd2_rgmii",
> +                                                    "eth_txd3_rgmii";
> +                                             function = "eth";
> +                                     };
> +                             };
> +
> +                             eth_rgmii_y_pins: eth-y-rgmii {
> +                                     mux {
> +                                             groups = "eth_mdio_y",
> +                                                    "eth_mdc_y",
> +                                                    "eth_rgmii_rx_clk_y",
> +                                                    "eth_rx_dv_y",
> +                                                    "eth_rxd0_y",
> +                                                    "eth_rxd1_y",
> +                                                    "eth_rxd2_rgmii",
> +                                                    "eth_rxd3_rgmii",
> +                                                    "eth_rgmii_tx_clk",
> +                                                    "eth_txen_y",
> +                                                    "eth_txd0_y",
> +                                                    "eth_txd1_y",
> +                                                    "eth_txd2_rgmii",
> +                                                    "eth_txd3_rgmii";
> +                                             function = "eth";
> +                                     };
> +                             };
>                       };
>               };

Reply via email to