This adds a driver core for the Realtek SMI chips and a subdriver
for the RTL8366RB. I just added this chip simply because it is
all I can test.
The code is a massaged variant of the code that has been sitting
out-of-tree in OpenWRT for years in the absence of a proper switch
subsystem. I have tried to credit the original authors wherever
possible.
The main changes I've done from the OpenWRT code:
- Added a callback to set the MAC address.
- Added an IRQ chip inside the RTL8366RB switch to demux and
handle the line state IRQs.
- Distributed the phy handling out to the PHY driver.
- Added some RTL8366RB code that was missing in the driver,
such as setting up "green ethernet" with a funny jam table
and forcing MAC5 (the CPU port) into 1 GBit.
Cc: Antti Seppälä <a.sepp...@gmail.com>
Cc: Roman Yeryomin <ro...@advem.lv>
Cc: Colin Leitner <colin.leit...@googlemail.com>
Cc: Gabor Juhos <juh...@openwrt.org>
Cc: Florian Fainelli <f.faine...@gmail.com>
Signed-off-by: Linus Walleij <linus.wall...@linaro.org>
---
drivers/net/dsa/Kconfig | 12 +
drivers/net/dsa/Makefile | 2 +
drivers/net/dsa/realtek-smi.c | 436 ++++++++++++++++
drivers/net/dsa/realtek-smi.h | 145 ++++++
drivers/net/dsa/rtl8366.c | 493 ++++++++++++++++++
drivers/net/dsa/rtl8366rb.c | 1103 +++++++++++++++++++++++++++++++++++++++++
6 files changed, 2191 insertions(+)
create mode 100644 drivers/net/dsa/realtek-smi.c
create mode 100644 drivers/net/dsa/realtek-smi.h
create mode 100644 drivers/net/dsa/rtl8366.c
create mode 100644 drivers/net/dsa/rtl8366rb.c
diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig
index 83a9bc892a3b..d25fa9a35ad3 100644
--- a/drivers/net/dsa/Kconfig
+++ b/drivers/net/dsa/Kconfig
@@ -52,6 +52,18 @@ config NET_DSA_QCA8K
This enables support for the Qualcomm Atheros QCA8K Ethernet
switch chips.
+config NET_DSA_RTK_SMI
+ tristate "Realtek SMI Ethernet switch family support"
+ depends on NET_DSA
+ # FIXME: select NET_DSA_TAG_RTK
+ select FIXED_PHY
+ select IRQ_DOMAIN
+ select REALTEK_PHY
+ select NET_DSA_TAG_TRAILER
+ ---help---
+ This enables support for the Realtek SMI-based switch
+ chips, currently only RTL8366RB.
+
config NET_DSA_SMSC_LAN9303
tristate
select NET_DSA_TAG_LAN9303
diff --git a/drivers/net/dsa/Makefile b/drivers/net/dsa/Makefile
index 4a5b5bd297ee..f660096cbad1 100644
--- a/drivers/net/dsa/Makefile
+++ b/drivers/net/dsa/Makefile
@@ -4,6 +4,8 @@ obj-$(CONFIG_NET_DSA_LOOP) += dsa_loop.o dsa_loop_bdinfo.o
obj-$(CONFIG_NET_DSA_MT7530) += mt7530.o
obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
obj-$(CONFIG_NET_DSA_QCA8K) += qca8k.o
+obj-$(CONFIG_NET_DSA_RTK_SMI) += realtek.o
+realtek-objs := realtek-smi.o rtl8366.o rtl8366rb.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303_I2C) += lan9303_i2c.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303_MDIO) += lan9303_mdio.o
diff --git a/drivers/net/dsa/realtek-smi.c b/drivers/net/dsa/realtek-smi.c
new file mode 100644
index 000000000000..de37b9a776fa
--- /dev/null
+++ b/drivers/net/dsa/realtek-smi.c
@@ -0,0 +1,436 @@
+/*
+ * Realtek Simple Management Interface (SMI) driver
+ * It can be discussed how "simple" this interface is.
+ *
+ * The SMI protocol piggy-backs the MDIO MDC and MDIO signals levels
+ * but the protocol is not MDIO at all. Instead it is a Realtek
+ * pecularity that need to bit-bang the lines in a special way to
+ * communicate with the switch.
+ *
+ * ASICs we intend to support with this driver:
+ *
+ * RTL8366 - The original version, apparently
+ * RTL8369 - Similar enough to have the same datsheet as RTL8366
+ * RTL8366RB - Probably reads out "RTL8366 revision B", has a quite
+ * different register layout from the other two
+ * RTL8366S - Is this "RTL8366 super"?
+ * RTL8367 - Has an OpenWRT driver as well
+ * RTL8368S - Seems to be an alternative name for RTL8366RB
+ * RTL8370 - Also uses SMI
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.wall...@linaro.org>
+ * Copyright (C) 2010 Antti Seppälä <a.sepp...@gmail.com>
+ * Copyright (C) 2010 Roman Yeryomin <ro...@advem.lv>
+ * Copyright (C) 2011 Colin Leitner <colin.leit...@googlemail.com>
+ * Copyright (C) 2009-2010 Gabor Juhos <juh...@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/spinlock.h>
+#include <linux/skbuff.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/bitops.h>
+#include <linux/if_bridge.h>
+
+#include "realtek-smi.h"
+
+#define REALTEK_SMI_ACK_RETRY_COUNT 5
+#define REALTEK_SMI_HW_STOP_DELAY 25 /* msecs */
+#define REALTEK_SMI_HW_START_DELAY 100 /* msecs */
+
+static inline void realtek_smi_clk_delay(struct realtek_smi *smi)
+{
+ ndelay(smi->clk_delay);
+}
+
+static void realtek_smi_start(struct realtek_smi *smi)
+{
+ /*
+ * Set GPIO pins to output mode, with initial state:
+ * SCK = 0, SDA = 1
+ */
+ gpiod_direction_output(smi->mdc, 0);
+ gpiod_direction_output(smi->mdio, 1);
+ realtek_smi_clk_delay(smi);
+
+ /* CLK 1: 0 -> 1, 1 -> 0 */
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 0);
+ realtek_smi_clk_delay(smi);
+
+ /* CLK 2: */
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdio, 0);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 0);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdio, 1);
+}
+
+static void realtek_smi_stop(struct realtek_smi *smi)
+{
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdio, 0);
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdio, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 0);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 1);
+
+ /* add a click */
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 0);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 1);
+
+ /* set GPIO pins to input mode */
+ gpiod_direction_input(smi->mdio);
+ gpiod_direction_input(smi->mdc);
+}
+
+static void realtek_smi_write_bits(struct realtek_smi *smi, u32 data, u32 len)
+{
+ for (; len > 0; len--) {
+ realtek_smi_clk_delay(smi);
+
+ /* prepare data */
+ gpiod_set_value(smi->mdio, !!(data & ( 1 << (len - 1))));
+ realtek_smi_clk_delay(smi);
+
+ /* clocking */
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ gpiod_set_value(smi->mdc, 0);
+ }
+}
+
+static void realtek_smi_read_bits(struct realtek_smi *smi, u32 len, u32 *data)
+{
+ gpiod_direction_input(smi->mdio);
+
+ for (*data = 0; len > 0; len--) {
+ u32 u;
+
+ realtek_smi_clk_delay(smi);
+
+ /* clocking */
+ gpiod_set_value(smi->mdc, 1);
+ realtek_smi_clk_delay(smi);
+ u = !!gpiod_get_value(smi->mdio);
+ gpiod_set_value(smi->mdc, 0);
+
+ *data |= (u << (len - 1));
+ }
+
+ gpiod_direction_output(smi->mdio, 0);
+}
+
+static int realtek_smi_wait_for_ack(struct realtek_smi *smi)
+{
+ int retry_cnt;
+
+ retry_cnt = 0;
+ do {
+ u32 ack;
+
+ realtek_smi_read_bits(smi, 1, &ack);
+ if (ack == 0)
+ break;
+
+ if (++retry_cnt > REALTEK_SMI_ACK_RETRY_COUNT) {
+ dev_err(smi->dev, "ACK timeout\n");
+ return -ETIMEDOUT;
+ }
+ } while (1);
+
+ return 0;
+}
+
+static int realtek_smi_write_byte(struct realtek_smi *smi, u8 data)
+{
+ realtek_smi_write_bits(smi, data, 8);
+ return realtek_smi_wait_for_ack(smi);
+}
+
+static int realtek_smi_write_byte_noack(struct realtek_smi *smi, u8 data)
+{
+ realtek_smi_write_bits(smi, data, 8);
+ return 0;
+}
+
+static int realtek_smi_read_byte0(struct realtek_smi *smi, u8 *data)
+{
+ u32 t;
+
+ /* read data */
+ realtek_smi_read_bits(smi, 8, &t);
+ *data = (t & 0xff);
+
+ /* send an ACK */
+ realtek_smi_write_bits(smi, 0x00, 1);
+
+ return 0;
+}
+
+static int realtek_smi_read_byte1(struct realtek_smi *smi, u8 *data)
+{
+ u32 t;
+
+ /* read data */
+ realtek_smi_read_bits(smi, 8, &t);
+ *data = (t & 0xff);
+
+ /* send an ACK */
+ realtek_smi_write_bits(smi, 0x01, 1);
+
+ return 0;
+}
+
+static int realtek_smi_read_reg(struct realtek_smi *smi, u32 addr, u32 *data)
+{
+ unsigned long flags;
+ u8 lo = 0;
+ u8 hi = 0;
+ int ret;
+
+ spin_lock_irqsave(&smi->lock, flags);
+
+ realtek_smi_start(smi);
+
+ /* send READ command */
+ ret = realtek_smi_write_byte(smi, smi->cmd_read);
+ if (ret)
+ goto out;
+
+ /* set ADDR[7:0] */
+ ret = realtek_smi_write_byte(smi, addr & 0xff);
+ if (ret)
+ goto out;
+
+ /* set ADDR[15:8] */
+ ret = realtek_smi_write_byte(smi, addr >> 8);
+ if (ret)
+ goto out;
+
+ /* read DATA[7:0] */
+ realtek_smi_read_byte0(smi, &lo);
+ /* read DATA[15:8] */
+ realtek_smi_read_byte1(smi, &hi);
+
+ *data = ((u32) lo) | (((u32) hi) << 8);
+
+ ret = 0;
+
+ out:
+ realtek_smi_stop(smi);
+ spin_unlock_irqrestore(&smi->lock, flags);
+
+ return ret;
+}
+
+static int realtek_smi_write_reg(struct realtek_smi *smi,
+ u32 addr, u32 data, bool ack)
+{
+ unsigned long flags;
+ int ret;
+
+ spin_lock_irqsave(&smi->lock, flags);
+
+ realtek_smi_start(smi);
+
+ /* send WRITE command */
+ ret = realtek_smi_write_byte(smi, smi->cmd_write);
+ if (ret)
+ goto out;
+
+ /* set ADDR[7:0] */
+ ret = realtek_smi_write_byte(smi, addr & 0xff);
+ if (ret)
+ goto out;
+
+ /* set ADDR[15:8] */
+ ret = realtek_smi_write_byte(smi, addr >> 8);
+ if (ret)
+ goto out;
+
+ /* write DATA[7:0] */
+ ret = realtek_smi_write_byte(smi, data & 0xff);
+ if (ret)
+ goto out;
+
+ /* write DATA[15:8] */
+ if (ack)
+ ret = realtek_smi_write_byte(smi, data >> 8);
+ else
+ ret = realtek_smi_write_byte_noack(smi, data >> 8);
+ if (ret)
+ goto out;
+
+ ret = 0;
+
+ out:
+ realtek_smi_stop(smi);
+ spin_unlock_irqrestore(&smi->lock, flags);
+
+ return ret;
+}
+
+/*
+ * There is one single case when we need to use this accessor and that
+ * is when issueing soft reset. Since the device reset as soon as we write
+ * that bit, no ACK will come back for natural reasons.
+ */
+int realtek_smi_write_reg_noack(struct realtek_smi *smi, u32 addr,
+ u32 data)
+{
+ return realtek_smi_write_reg(smi, addr, data, false);
+}
+EXPORT_SYMBOL_GPL(realtek_smi_write_reg_noack);
+
+/* Regmap accessors */
+
+static int realtek_smi_write(void *ctx, u32 reg, u32 val)
+{
+ struct realtek_smi *smi = ctx;
+
+ return realtek_smi_write_reg(smi, reg, val, true);
+}
+
+static int realtek_smi_read(void *ctx, u32 reg, u32 *val)
+{
+ struct realtek_smi *smi = ctx;
+
+ return realtek_smi_read_reg(smi, reg, val);
+}
+
+static const struct regmap_config realtek_smi_mdio_regmap_config = {
+ .reg_bits = 10, /* A4..A0 R4..R0 */
+ .val_bits = 16,
+ .reg_stride = 1,
+ /* phy regs are at 0x8000 */
+ .max_register = 0xffff,
+ .reg_format_endian = REGMAP_ENDIAN_LITTLE,
+ .reg_read = realtek_smi_read,
+ .reg_write = realtek_smi_write,
+ .cache_type = REGCACHE_NONE,
+};
+
+static int realtek_smi_probe(struct platform_device *pdev)
+{
+ struct realtek_smi *smi;
+ struct device *dev = &pdev->dev;
+ const struct realtek_smi_variant *var = of_device_get_match_data(dev);
+ int ret;
+
+ smi = devm_kzalloc(dev, sizeof(*smi), GFP_KERNEL);
+ if (!smi)
+ return -ENOMEM;
+ smi->map = devm_regmap_init(dev, NULL, smi,
+ &realtek_smi_mdio_regmap_config);
+ if (IS_ERR(smi->map)) {
+ ret = PTR_ERR(smi->map);
+ dev_err(dev, "regmap init failed: %d\n", ret);
+ return ret;
+ }
+
+ /* link forward and backward */
+ smi->dev = dev;
+ smi->clk_delay = var->clk_delay;
+ smi->cmd_read = var->cmd_read;
+ smi->cmd_write = var->cmd_write;
+ smi->ops = var->ops;
+
+ dev_set_drvdata(dev, smi);
+ spin_lock_init(&smi->lock);
+
+ /* TODO: if power is software controlled, set up any regulators here */
+
+ /* Assert then deassert RESET */
+ smi->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(smi->reset)) {
+ dev_err(dev, "failed to get RESET GPIO\n");
+ return PTR_ERR(smi->reset);
+ }
+ msleep(REALTEK_SMI_HW_STOP_DELAY);
+ gpiod_set_value(smi->reset, 0);
+ msleep(REALTEK_SMI_HW_START_DELAY);
+ dev_info(dev, "deasserted RESET\n");
+
+ /* Fetch MDIO pins */
+ smi->mdc = devm_gpiod_get_optional(dev, "mdc", GPIOD_OUT_LOW);
+ if (IS_ERR(smi->mdc))
+ return PTR_ERR(smi->mdc);
+ smi->mdio = devm_gpiod_get_optional(dev, "mdio", GPIOD_OUT_LOW);
+ if (IS_ERR(smi->mdio))
+ return PTR_ERR(smi->mdio);
+
+ ret = smi->ops->detect(smi);
+ if (ret) {
+ dev_err(dev, "unable to detect switch\n");
+ return ret;
+ }
+
+ smi->ds = dsa_switch_alloc(dev, smi->num_ports);
+ if (!smi->ds)
+ return -ENOMEM;
+ smi->ds->priv = smi;
+ smi->ds->ops = var->ds_ops;
+
+ ret = dsa_register_switch(smi->ds);
+ if (ret) {
+ dev_err(dev, "unable to register switch ret = %d\n", ret);
+ return ret;
+ }
+ return 0;
+}
+
+static int realtek_smi_remove(struct platform_device *pdev)
+{
+ struct realtek_smi *smi = dev_get_drvdata(&pdev->dev);
+
+ dsa_unregister_switch(smi->ds);
+ gpiod_set_value(smi->reset, 1);
+
+ return 0;
+}
+
+static const struct of_device_id realtek_smi_of_match[] = {
+ {
+ .compatible = "realtek,rtl8366rb",
+ .data = &rtl8366rb_variant,
+ },
+ {
+ /* FIXME: add support for RTL8366S and more */
+ .compatible = "realtek,rtl8366s",
+ .data = NULL,
+ },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, realtek_smi_of_match);
+
+static struct platform_driver realtek_smi_driver = {
+ .driver = {
+ .name = "realtek-smi",
+ .of_match_table = of_match_ptr(realtek_smi_of_match),
+ },
+ .probe = realtek_smi_probe,
+ .remove = realtek_smi_remove,
+};
+module_platform_driver(realtek_smi_driver);
diff --git a/drivers/net/dsa/realtek-smi.h b/drivers/net/dsa/realtek-smi.h
new file mode 100644
index 000000000000..682895e932ab
--- /dev/null
+++ b/drivers/net/dsa/realtek-smi.h
@@ -0,0 +1,145 @@
+/*
+ * Realtek SMI interface driver defines
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.wall...@linaro.org>
+ * Copyright (C) 2009-2010 Gabor Juhos <juh...@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#ifndef _REALTEK_SMI_H
+#define _REALTEK_SMI_H
+
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/gpio/consumer.h>
+#include <net/dsa.h>
+
+struct realtek_smi_ops;
+struct dentry;
+struct inode;
+struct file;
+
+struct rtl8366_mib_counter {
+ unsigned base;
+ unsigned offset;
+ unsigned length;
+ const char *name;
+};
+
+struct rtl8366_vlan_mc {
+ u16 vid;
+ u16 untag;
+ u16 member;
+ u8 fid;
+ u8 priority;
+};
+
+struct rtl8366_vlan_4k {
+ u16 vid;
+ u16 untag;
+ u16 member;
+ u8 fid;
+};
+
+struct realtek_smi {
+ struct device *dev;
+ struct gpio_desc *reset;
+ struct gpio_desc *mdc;
+ struct gpio_desc *mdio;
+ struct regmap *map;
+ unsigned int clk_delay;
+ u8 cmd_read;
+ u8 cmd_write;
+ spinlock_t lock;
+ struct dsa_switch *ds;
+ struct irq_domain *irqdomain;
+
+ unsigned int cpu_port;
+ unsigned int num_ports;
+ unsigned int num_vlan_mc;
+ unsigned int num_mib_counters;
+ struct rtl8366_mib_counter *mib_counters;
+
+ const struct realtek_smi_ops *ops;
+
+ int vlan_enabled;
+ int vlan4k_enabled;
+
+ char buf[4096];
+#ifdef CONFIG_RTL8366_SMI_DEBUG_FS
+ struct dentry *debugfs_root;
+ u8 dbg_vlan_4k_page;
+#endif
+};
+
+/**
+ * struct realtek_smi_ops - vtable for the per-SMI-chiptype operations
+ * @detect: detects the chiptype
+ */
+struct realtek_smi_ops {
+ int (*detect)(struct realtek_smi *smi);
+ int (*reset_chip)(struct realtek_smi *smi);
+ int (*setup)(struct realtek_smi *smi);
+ void (*cleanup)(struct realtek_smi *smi);
+ int (*get_mib_counter)(struct realtek_smi *smi,
+ int port,
+ struct rtl8366_mib_counter *mib,
+ u64 *mibvalue);
+ int (*get_vlan_mc)(struct realtek_smi *smi, u32 index,
+ struct rtl8366_vlan_mc *vlanmc);
+ int (*set_vlan_mc)(struct realtek_smi *smi, u32 index,
+ const struct rtl8366_vlan_mc *vlanmc);
+ int (*get_vlan_4k)(struct realtek_smi *smi, u32 vid,
+ struct rtl8366_vlan_4k *vlan4k);
+ int (*set_vlan_4k)(struct realtek_smi *smi,
+ const struct rtl8366_vlan_4k *vlan4k);
+ int (*get_mc_index)(struct realtek_smi *smi, int port, int *val);
+ int (*set_mc_index)(struct realtek_smi *smi, int port, int index);
+ bool (*is_vlan_valid)(struct realtek_smi *smi, unsigned vlan);
+ int (*enable_vlan)(struct realtek_smi *smi, bool enable);
+ int (*enable_vlan4k)(struct realtek_smi *smi, bool enable);
+ int (*enable_port)(struct realtek_smi *smi, int port, bool enable);
+};
+
+struct realtek_smi_variant {
+ const struct dsa_switch_ops *ds_ops;
+ const struct realtek_smi_ops *ops;
+ unsigned int clk_delay;
+ u8 cmd_read;
+ u8 cmd_write;
+};
+
+/* SMI core calls */
+int realtek_smi_write_reg_noack(struct realtek_smi *smi, u32 addr,
+ u32 data);
+
+/* RTL8366 library helpers */
+int rtl8366_mc_is_used(struct realtek_smi *smi, int mc_index, int *used);
+int rtl8366_set_vlan(struct realtek_smi *smi, int vid, u32 member,
+ u32 untag, u32 fid);
+int rtl8366_get_pvid(struct realtek_smi *smi, int port, int *val);
+int rtl8366_set_pvid(struct realtek_smi *smi, unsigned port,
+ unsigned vid);
+int rtl8366_enable_vlan4k(struct realtek_smi *smi, bool enable);
+int rtl8366_enable_vlan(struct realtek_smi *smi, bool enable);
+int rtl8366_reset_vlan(struct realtek_smi *smi);
+int rtl8366_init_vlan(struct realtek_smi *smi);
+int rtl8366_vlan_filtering(struct dsa_switch *ds, int port, bool
vlan_filtering);
+int rtl8366_vlan_prepare(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan,
+ struct switchdev_trans *trans);
+void rtl8366_vlan_add(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan,
+ struct switchdev_trans *trans);
+int rtl8366_vlan_del(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan);
+void rtl8366_get_strings(struct dsa_switch *ds, int port, uint8_t *data);
+int rtl8366_get_sset_count(struct dsa_switch *ds);
+void rtl8366_get_ethtool_stats(struct dsa_switch *ds, int port, uint64_t
*data);
+
+extern const struct realtek_smi_variant rtl8366rb_variant;
+
+#endif /* _REALTEK_SMI_H */
diff --git a/drivers/net/dsa/rtl8366.c b/drivers/net/dsa/rtl8366.c
new file mode 100644
index 000000000000..bb50cf9e2074
--- /dev/null
+++ b/drivers/net/dsa/rtl8366.c
@@ -0,0 +1,493 @@
+/*
+ * Realtek SMI library helpers for the RTL8366x variants
+ * RTL8366RB and RTL8366S
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.wall...@linaro.org>
+ * Copyright (C) 2009-2010 Gabor Juhos <juh...@openwrt.org>
+ * Copyright (C) 2010 Antti Seppälä <a.sepp...@gmail.com>
+ * Copyright (C) 2010 Roman Yeryomin <ro...@advem.lv>
+ * Copyright (C) 2011 Colin Leitner <colin.leit...@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <net/dsa.h>
+#include <linux/if_bridge.h>
+#include "realtek-smi.h"
+
+int rtl8366_mc_is_used(struct realtek_smi *smi, int mc_index, int *used)
+{
+ int ret;
+ int i;
+
+ *used = 0;
+ for (i = 0; i < smi->num_ports; i++) {
+ int index = 0;
+
+ ret = smi->ops->get_mc_index(smi, i, &index);
+ if (ret)
+ return ret;
+
+ if (mc_index == index) {
+ *used = 1;
+ break;
+ }
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_mc_is_used);
+
+int rtl8366_set_vlan(struct realtek_smi *smi, int vid, u32 member,
+ u32 untag, u32 fid)
+{
+ struct rtl8366_vlan_4k vlan4k;
+ int ret;
+ int i;
+
+ /* Update the 4K table */
+ ret = smi->ops->get_vlan_4k(smi, vid, &vlan4k);
+ if (ret)
+ return ret;
+
+ vlan4k.member = member;
+ vlan4k.untag = untag;
+ vlan4k.fid = fid;
+ ret = smi->ops->set_vlan_4k(smi, &vlan4k);
+ if (ret)
+ return ret;
+
+ /* Try to find an existing MC entry for this VID */
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ struct rtl8366_vlan_mc vlanmc;
+
+ ret = smi->ops->get_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ if (vid == vlanmc.vid) {
+ /* update the MC entry */
+ vlanmc.member = member;
+ vlanmc.untag = untag;
+ vlanmc.fid = fid;
+
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ break;
+ }
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(rtl8366_set_vlan);
+
+int rtl8366_get_pvid(struct realtek_smi *smi, int port, int *val)
+{
+ struct rtl8366_vlan_mc vlanmc;
+ int ret;
+ int index;
+
+ ret = smi->ops->get_mc_index(smi, port, &index);
+ if (ret)
+ return ret;
+
+ ret = smi->ops->get_vlan_mc(smi, index, &vlanmc);
+ if (ret)
+ return ret;
+
+ *val = vlanmc.vid;
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_get_pvid);
+
+int rtl8366_set_pvid(struct realtek_smi *smi, unsigned port,
+ unsigned vid)
+{
+ struct rtl8366_vlan_mc vlanmc;
+ struct rtl8366_vlan_4k vlan4k;
+ int ret;
+ int i;
+
+ /* Try to find an existing MC entry for this VID */
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ ret = smi->ops->get_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ if (vid == vlanmc.vid) {
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ ret = smi->ops->set_mc_index(smi, port, i);
+ return ret;
+ }
+ }
+
+ /* We have no MC entry for this VID, try to find an empty one */
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ ret = smi->ops->get_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ if (vlanmc.vid == 0 && vlanmc.member == 0) {
+ /* Update the entry from the 4K table */
+ ret = smi->ops->get_vlan_4k(smi, vid, &vlan4k);
+ if (ret)
+ return ret;
+
+ vlanmc.vid = vid;
+ vlanmc.member = vlan4k.member;
+ vlanmc.untag = vlan4k.untag;
+ vlanmc.fid = vlan4k.fid;
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ ret = smi->ops->set_mc_index(smi, port, i);
+ return ret;
+ }
+ }
+
+ /* MC table is full, try to find an unused entry and replace it */
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ int used;
+
+ ret = rtl8366_mc_is_used(smi, i, &used);
+ if (ret)
+ return ret;
+
+ if (!used) {
+ /* Update the entry from the 4K table */
+ ret = smi->ops->get_vlan_4k(smi, vid, &vlan4k);
+ if (ret)
+ return ret;
+
+ vlanmc.vid = vid;
+ vlanmc.member = vlan4k.member;
+ vlanmc.untag = vlan4k.untag;
+ vlanmc.fid = vlan4k.fid;
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ ret = smi->ops->set_mc_index(smi, port, i);
+ return ret;
+ }
+ }
+
+ dev_err(smi->dev,
+ "all VLAN member configurations are in use\n");
+
+ return -ENOSPC;
+}
+EXPORT_SYMBOL_GPL(rtl8366_set_pvid);
+
+int rtl8366_enable_vlan4k(struct realtek_smi *smi, bool enable)
+{
+ int ret;
+
+ if (enable) {
+ ret = smi->ops->enable_vlan(smi, true);
+ if (ret)
+ return ret;
+
+ smi->vlan_enabled = true;
+ }
+
+ ret = smi->ops->enable_vlan4k(smi, enable);
+ if (ret)
+ return ret;
+
+ smi->vlan4k_enabled = enable;
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_enable_vlan4k);
+
+int rtl8366_enable_vlan(struct realtek_smi *smi, bool enable)
+{
+ int ret;
+
+ ret = smi->ops->enable_vlan(smi, true);
+ if (ret)
+ return ret;
+
+ smi->vlan_enabled = enable;
+
+ if (!enable) {
+ smi->vlan4k_enabled = false;
+ ret = smi->ops->enable_vlan4k(smi, false);
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(rtl8366_enable_vlan);
+
+int rtl8366_reset_vlan(struct realtek_smi *smi)
+{
+ struct rtl8366_vlan_mc vlanmc;
+ int ret;
+ int i;
+
+ rtl8366_enable_vlan(smi, false);
+ rtl8366_enable_vlan4k(smi, false);
+
+ /* clear VLAN member configurations */
+ vlanmc.vid = 0;
+ vlanmc.priority = 0;
+ vlanmc.member = 0;
+ vlanmc.untag = 0;
+ vlanmc.fid = 0;
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_reset_vlan);
+
+int rtl8366_init_vlan(struct realtek_smi *smi)
+{
+ int port;
+ int ret;
+
+ ret = rtl8366_reset_vlan(smi);
+ if (ret)
+ return ret;
+
+ for (port = 0; port < smi->num_ports; port++) {
+ u32 mask;
+
+ if (port == smi->cpu_port)
+ mask = (1 << smi->num_ports) - 1;
+ else
+ mask = (1 << port) | (1 << smi->cpu_port);
+
+ ret = rtl8366_set_vlan(smi, (port + 1), mask, mask, 0);
+ if (ret)
+ return ret;
+
+ ret = rtl8366_set_pvid(smi, port, (port + 1));
+ if (ret)
+ return ret;
+ }
+
+ return rtl8366_enable_vlan(smi, true);
+}
+EXPORT_SYMBOL_GPL(rtl8366_init_vlan);
+
+int rtl8366_vlan_filtering(struct dsa_switch *ds, int port, bool
vlan_filtering)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8366_vlan_4k vlan4k;
+ int ret;
+
+ if (!smi->ops->is_vlan_valid(smi, port))
+ return -EINVAL;
+
+ dev_info(smi->dev, "%s filtering on port %d\n",
+ vlan_filtering ? "enable" : "disable",
+ port);
+
+ /*
+ * FIXME:
+ * The hardware support filter ID (FID) 0..7, I have no clue how to
+ * support this in the driver when the callback only says on/off.
+ */
+ ret = smi->ops->get_vlan_4k(smi, port, &vlan4k);
+ if (ret)
+ return ret;
+
+ /* Just set the filter to FID 1 for now then */
+ ret = rtl8366_set_vlan(smi, port,
+ vlan4k.member,
+ vlan4k.untag,
+ 1);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_vlan_filtering);
+
+int rtl8366_vlan_prepare(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan,
+ struct switchdev_trans *trans)
+{
+ struct realtek_smi *smi = ds->priv;
+ int ret;
+
+ if (!smi->ops->is_vlan_valid(smi, port))
+ return -EINVAL;
+
+ dev_info(smi->dev, "prepare VLANs %04x..%04x\n",
+ vlan->vid_begin, vlan->vid_end);
+
+ /*
+ * FIXME: what's with this 4k business?
+ * Just rtl8366_enable_vlan() seems inconclusive.
+ */
+
+ /* Enable VLAN in the hardware */
+ ret = rtl8366_enable_vlan4k(smi, true);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_vlan_prepare);
+
+void rtl8366_vlan_add(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan,
+ struct switchdev_trans *trans)
+{
+ struct realtek_smi *smi = ds->priv;
+ bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
+ bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID;
+ u32 member = 0;
+ u32 untag = 0;
+ u16 vid;
+ int ret;
+
+ if (!smi->ops->is_vlan_valid(smi, port))
+ return;
+
+ dev_info(smi->dev, "add VLAN on port %d, %s, %s\n",
+ port,
+ untagged ? "untagged" : "tagged",
+ pvid ? " PVID" : "no PVID");
+
+ if (dsa_is_dsa_port(ds, port) || dsa_is_cpu_port(ds, port)) {
+ dev_err(smi->dev, "port is DSA or CPU port\n");
+ }
+
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
+ int pvid_val = 0;
+
+ dev_info(smi->dev, "add VLAN %04x\n", vid);
+ member |= BIT(port);
+
+ if (untagged)
+ untag |= BIT(port);
+
+ /*
+ * To ensure that we have a valid MC entry for this VLAN,
+ * initialize the port VLAN ID here.
+ */
+ ret = rtl8366_get_pvid(smi, port, &pvid_val);
+ if (ret < 0) {
+ dev_err(smi->dev, "could not lookup PVID for port %d\n",
+ port);
+ return;
+ }
+ if (pvid_val == 0) {
+ ret = rtl8366_set_pvid(smi, port, vid);
+ if (ret < 0)
+ return;
+ }
+ }
+
+ ret = rtl8366_set_vlan(smi, port, member, untag, 0);
+ if (ret)
+ dev_err(smi->dev,
+ "failed to set up VLAN %04x",
+ vid);
+}
+EXPORT_SYMBOL_GPL(rtl8366_vlan_add);
+
+int rtl8366_vlan_del(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ struct realtek_smi *smi = ds->priv;
+ u16 vid;
+ int ret;
+
+ dev_info(smi->dev, "del VLAN on port %d\n", port);
+
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
+ int i;
+
+ dev_info(smi->dev, "del VLAN %04x\n", vid);
+
+ for (i = 0; i < smi->num_vlan_mc; i++) {
+ struct rtl8366_vlan_mc vlanmc;
+
+ ret = smi->ops->get_vlan_mc(smi, i, &vlanmc);
+ if (ret)
+ return ret;
+
+ if (vid == vlanmc.vid) {
+ /* clear VLAN member configurations */
+ vlanmc.vid = 0;
+ vlanmc.priority = 0;
+ vlanmc.member = 0;
+ vlanmc.untag = 0;
+ vlanmc.fid = 0;
+
+ ret = smi->ops->set_vlan_mc(smi, i, &vlanmc);
+ if (ret) {
+ dev_err(smi->dev,
+ "failed to remove VLAN %04x\n",
+ vid);
+ return ret;
+ }
+ break;
+ }
+ }
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rtl8366_vlan_del);
+
+void rtl8366_get_strings(struct dsa_switch *ds, int port, uint8_t *data)
+{
+ struct realtek_smi *smi = ds->priv;
+ struct rtl8366_mib_counter *mib;
+ int i;
+
+ if (port >= smi->num_ports)
+ return;
+
+ for (i = 0; i < smi->num_mib_counters; i++) {
+ mib = &smi->mib_counters[i];
+ memcpy(data + i * ETH_GSTRING_LEN,
+ mib->name, ETH_GSTRING_LEN);
+ }
+}
+EXPORT_SYMBOL_GPL(rtl8366_get_strings);
+
+int rtl8366_get_sset_count(struct dsa_switch *ds)
+{
+ struct realtek_smi *smi = ds->priv;
+
+ return smi->num_mib_counters;
+}
+EXPORT_SYMBOL_GPL(rtl8366_get_sset_count);
+
+void rtl8366_get_ethtool_stats(struct dsa_switch *ds, int port, uint64_t *data)
+{
+ struct realtek_smi *smi = ds->priv;
+ int i;
+ int ret;
+
+ if (port >= smi->num_ports)
+ return;
+
+ for (i = 0; i < smi->num_mib_counters; i++) {
+ struct rtl8366_mib_counter *mib;
+ u64 mibvalue;
+
+ mib = &smi->mib_counters[i];
+ ret = smi->ops->get_mib_counter(smi, port, mib, &mibvalue);
+ if (ret) {
+ dev_err(smi->dev, "error reading MIB counter %s\n",
+ mib->name);
+ }
+ data[i] = mibvalue;
+ }
+}
+EXPORT_SYMBOL_GPL(rtl8366_get_ethtool_stats);
diff --git a/drivers/net/dsa/rtl8366rb.c b/drivers/net/dsa/rtl8366rb.c
new file mode 100644
index 000000000000..765ca72cc399
--- /dev/null
+++ b/drivers/net/dsa/rtl8366rb.c
@@ -0,0 +1,1103 @@
+/*
+ * Realtek SMI subdriver for the Realtek RTL8366RB ethernet switch
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.wall...@linaro.org>
+ * Copyright (C) 2009-2010 Gabor Juhos <juh...@openwrt.org>
+ * Copyright (C) 2010 Antti Seppälä <a.sepp...@gmail.com>
+ * Copyright (C) 2010 Roman Yeryomin <ro...@advem.lv>
+ * Copyright (C) 2011 Colin Leitner <colin.leit...@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/regmap.h>
+#include <linux/bitops.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/of_irq.h>
+
+#include "realtek-smi.h"
+
+#define RTL8366RB_PORT_NUM_CPU 5
+#define RTL8366RB_NUM_PORTS 6
+#define RTL8366RB_PHY_NO_MAX 4
+#define RTL8366RB_PHY_ADDR_MAX 31
+
+#define RTL8366RB_PAACR0 0x10 /* bits 0..7 = port 0, bits 8..15
= port 1 */
+#define RTL8366RB_PAACR1 0x11 /* bits 0..7 = port 2, bits 8..15
= port 3 */
+#define RTL8366RB_PAACR2 0x12 /* bits 0..7 = port 4, bits 8..15
= port 5 */
+#define RTL8366RB_PAACR_SPEED_10M 0
+#define RTL8366RB_PAACR_SPEED_100M 1
+#define RTL8366RB_PAACR_SPEED_1000M 2
+#define RTL8366RB_PAACR_FULL_DUPLEX BIT(2)
+#define RTL8366RB_PAACR_LINK_UP BIT(4)
+#define RTL8366RB_PAACR_TX_PAUSE BIT(5)
+#define RTL8366RB_PAACR_RX_PAUSE BIT(6)
+#define RTL8366RB_PAACR_AN BIT(7)
+
+#define RTL8366RB_PAACR_CPU_PORT (RTL8366RB_PAACR_SPEED_1000M | \
+ RTL8366RB_PAACR_FULL_DUPLEX | \
+ RTL8366RB_PAACR_LINK_UP | \
+ RTL8366RB_PAACR_TX_PAUSE | \
+ RTL8366RB_PAACR_RX_PAUSE)
+
+#define RTL8366RB_PSTAT0 0x14 /* bits 0..7 = port 0, bits 8..15
= port 1 */
+#define RTL8366RB_PSTAT1 0x15 /* bits 0..7 = port 2, bits 8..15
= port 3 */
+#define RTL8366RB_PSTAT2 0x16 /* bits 0..7 = port 4, bits 8..15
= port 5 */
+
+#define RTL8366RB_POWER_SAVING_REG 0x21
+
+/* CPU port control reg */
+#define RTL8368RB_CPU_CTRL_REG 0x0061
+#define RTL8368RB_CPU_PORTS_OFF 0
+#define RTL8368RB_CPU_PORTS_MSK 0x00FF
+#define RTL8368RB_CPU_INSTAG BIT(15) /* enables inserting custom tag
length/type 8899 */
+
+#define RTL8366RB_SMAR0 0x0070 /* bits 0..15 */
+#define RTL8366RB_SMAR1 0x0071 /* bits 16..31 */
+#define RTL8366RB_SMAR2 0x0072 /* bits 32..47 */
+
+/* Switch Global Configuration register */
+#define RTL8366RB_SGCR 0x0000
+#define RTL8366RB_SGCR_EN_BC_STORM_CTRL BIT(0)
+#define RTL8366RB_SGCR_MAX_LENGTH(_x) (_x << 4)
+#define RTL8366RB_SGCR_MAX_LENGTH_MASK RTL8366RB_SGCR_MAX_LENGTH(0x3)
+#define RTL8366RB_SGCR_MAX_LENGTH_1522 RTL8366RB_SGCR_MAX_LENGTH(0x0)
+#define RTL8366RB_SGCR_MAX_LENGTH_1536 RTL8366RB_SGCR_MAX_LENGTH(0x1)
+#define RTL8366RB_SGCR_MAX_LENGTH_1552 RTL8366RB_SGCR_MAX_LENGTH(0x2)
+#define RTL8366RB_SGCR_MAX_LENGTH_9216 RTL8366RB_SGCR_MAX_LENGTH(0x3)
+#define RTL8366RB_SGCR_EN_VLAN BIT(13)
+#define RTL8366RB_SGCR_EN_VLAN_4KTB BIT(14)
+
+/* Port Enable Control register */
+#define RTL8366RB_PECR 0x0001
+
+/* Port Mirror Control Register */
+#define RTL8366RB_PMCR 0x0007
+#define RTL8366RB_PMCR_SOURCE_PORT(_x) (_x)
+#define RTL8366RB_PMCR_SOURCE_PORT_MASK 0x000f
+#define RTL8366RB_PMCR_MONITOR_PORT(_x) ((_x) << 4)
+#define RTL8366RB_PMCR_MONITOR_PORT_MASK 0x00f0
+#define RTL8366RB_PMCR_MIRROR_RX BIT(8)
+#define RTL8366RB_PMCR_MIRROR_TX BIT(9)
+#define RTL8366RB_PMCR_MIRROR_SPC BIT(10)
+#define RTL8366RB_PMCR_MIRROR_ISO BIT(11)
+
+/* Switch Security Control registers */
+#define RTL8366RB_SSCR0 0x0002
+#define RTL8366RB_SSCR1 0x0003
+#define RTL8366RB_SSCR2 0x0004
+#define RTL8366RB_SSCR2_DROP_UNKNOWN_DA BIT(0)
+
+#define RTL8366RB_RESET_CTRL_REG 0x0100
+#define RTL8366RB_CHIP_CTRL_RESET_HW 1
+#define RTL8366RB_CHIP_CTRL_RESET_SW (1 << 1)
+
+#define RTL8366RB_CHIP_ID_REG 0x0509
+#define RTL8366RB_CHIP_ID_8366 0x5937
+#define RTL8366RB_CHIP_VERSION_CTRL_REG 0x050A
+#define RTL8366RB_CHIP_VERSION_MASK 0xf
+
+/* PHY registers control */
+#define RTL8366RB_PHY_ACCESS_CTRL_REG 0x8000
+#define RTL8366RB_PHY_CTRL_READ BIT(0)
+#define RTL8366RB_PHY_CTRL_WRITE 0
+#define RTL8366RB_PHY_ACCESS_BUSY_REG 0x8001
+#define RTL8366RB_PHY_INT_BUSY BIT(0)
+#define RTL8366RB_PHY_EXT_BUSY BIT(4)
+#define RTL8366RB_PHY_ACCESS_DATA_REG 0x8002
+#define RTL8366RB_PHY_EXT_CTRL_REG 0x8010
+#define RTL8366RB_PHY_EXT_WRDATA_REG 0x8011
+#define RTL8366RB_PHY_EXT_RDDATA_REG 0x8012
+
+#define RTL8366RB_PHY_REG_MASK 0x1f
+#define RTL8366RB_PHY_PAGE_OFFSET 5
+#define RTL8366RB_PHY_PAGE_MASK (0xf << 5)
+#define RTL8366RB_PHY_NO_OFFSET 9
+#define RTL8366RB_PHY_NO_MASK (0x1f << 9)
+
+#define RTL8366RB_VLAN_INGRESS_CTRL2_REG 0x037f
+
+/* LED control registers */
+#define RTL8366RB_LED_BLINKRATE_REG 0x0430
+#define RTL8366RB_LED_BLINKRATE_BIT 0
+#define RTL8366RB_LED_BLINKRATE_MASK 0x0007
+
+#define RTL8366RB_LED_CTRL_REG 0x0431
+#define RTL8366RB_LED_0_1_CTRL_REG 0x0432
+#define RTL8366RB_LED_2_3_CTRL_REG 0x0433
+
+#define RTL8366RB_MIB_COUNT 33
+#define RTL8366RB_GLOBAL_MIB_COUNT 1
+#define RTL8366RB_MIB_COUNTER_PORT_OFFSET 0x0050
+#define RTL8366RB_MIB_COUNTER_BASE 0x1000
+#define RTL8366RB_MIB_CTRL_REG 0x13F0
+#define RTL8366RB_MIB_CTRL_USER_MASK 0x0FFC
+#define RTL8366RB_MIB_CTRL_BUSY_MASK BIT(0)
+#define RTL8366RB_MIB_CTRL_RESET_MASK BIT(1)
+#define RTL8366RB_MIB_CTRL_PORT_RESET(_p) BIT(2 + (_p))
+#define RTL8366RB_MIB_CTRL_GLOBAL_RESET BIT(11)
+
+#define RTL8366RB_PORT_VLAN_CTRL_BASE 0x0063
+#define RTL8366RB_PORT_VLAN_CTRL_REG(_p) \
+ (RTL8366RB_PORT_VLAN_CTRL_BASE + (_p) / 4)
+#define RTL8366RB_PORT_VLAN_CTRL_MASK 0xf
+#define RTL8366RB_PORT_VLAN_CTRL_SHIFT(_p) (4 * ((_p) % 4))
+
+#define RTL8366RB_VLAN_TABLE_READ_BASE 0x018C
+#define RTL8366RB_VLAN_TABLE_WRITE_BASE 0x0185
+
+#define RTL8366RB_TABLE_ACCESS_CTRL_REG 0x0180
+#define RTL8366RB_TABLE_VLAN_READ_CTRL 0x0E01
+#define RTL8366RB_TABLE_VLAN_WRITE_CTRL 0x0F01
+
+#define RTL8366RB_VLAN_MC_BASE(_x) (0x0020 + (_x) * 3)
+
+#define RTL8366RB_PORT_LINK_STATUS_BASE 0x0014
+#define RTL8366RB_PORT_STATUS_SPEED_MASK 0x0003
+#define RTL8366RB_PORT_STATUS_DUPLEX_MASK 0x0004
+#define RTL8366RB_PORT_STATUS_LINK_MASK 0x0010
+#define RTL8366RB_PORT_STATUS_TXPAUSE_MASK 0x0020
+#define RTL8366RB_PORT_STATUS_RXPAUSE_MASK 0x0040
+#define RTL8366RB_PORT_STATUS_AN_MASK 0x0080
+
+#define RTL8366RB_NUM_VLANS 16
+#define RTL8366RB_NUM_LEDGROUPS 4
+#define RTL8366RB_NUM_VIDS 4096
+#define RTL8366RB_PRIORITYMAX 7
+#define RTL8366RB_FIDMAX 7
+
+#define RTL8366RB_PORT_1 (1 << 0) /* In userspace port 0 */
+#define RTL8366RB_PORT_2 (1 << 1) /* In userspace port 1 */
+#define RTL8366RB_PORT_3 (1 << 2) /* In userspace port 2 */
+#define RTL8366RB_PORT_4 (1 << 3) /* In userspace port 3 */
+#define RTL8366RB_PORT_5 (1 << 4) /* In userspace port 4 */
+
+#define RTL8366RB_PORT_CPU (1 << 5) /* CPU port */
+
+#define RTL8366RB_PORT_ALL (RTL8366RB_PORT_1 | \
+ RTL8366RB_PORT_2 | \
+ RTL8366RB_PORT_3 | \
+ RTL8366RB_PORT_4 | \
+ RTL8366RB_PORT_5 | \
+ RTL8366RB_PORT_CPU)
+
+#define RTL8366RB_PORT_ALL_BUT_CPU (RTL8366RB_PORT_1 | \
+ RTL8366RB_PORT_2 | \
+ RTL8366RB_PORT_3 | \
+ RTL8366RB_PORT_4 | \
+ RTL8366RB_PORT_5)
+
+#define RTL8366RB_PORT_ALL_EXTERNAL (RTL8366RB_PORT_1 | \
+ RTL8366RB_PORT_2 | \
+ RTL8366RB_PORT_3 | \
+ RTL8366RB_PORT_4)
+
+#define RTL8366RB_PORT_ALL_INTERNAL RTL8366RB_PORT_CPU
+
+#define RTL8366RB_VLAN_VID_MASK 0xfff
+#define RTL8366RB_VLAN_PRIORITY_SHIFT 12
+#define RTL8366RB_VLAN_PRIORITY_MASK 0x7
+#define RTL8366RB_VLAN_UNTAG_SHIFT 8
+#define RTL8366RB_VLAN_UNTAG_MASK 0xff
+#define RTL8366RB_VLAN_MEMBER_MASK 0xff
+#define RTL8366RB_VLAN_FID_MASK 0x7
+
+
+/* Port ingress bandwidth control */
+#define RTL8366RB_IB_BASE 0x0200
+#define RTL8366RB_IB_REG(pnum) (RTL8366RB_IB_BASE + pnum)
+#define RTL8366RB_IB_BDTH_MASK 0x3fff
+#define RTL8366RB_IB_PREIFG_OFFSET 14
+#define RTL8366RB_IB_PREIFG_MASK (1 << RTL8366RB_IB_PREIFG_OFFSET)
+
+/* Port egress bandwidth control */
+#define RTL8366RB_EB_BASE 0x02d1
+#define RTL8366RB_EB_REG(pnum) (RTL8366RB_EB_BASE + pnum)
+#define RTL8366RB_EB_BDTH_MASK 0x3fff
+#define RTL8366RB_EB_PREIFG_REG 0x02f8
+#define RTL8366RB_EB_PREIFG_OFFSET 9
+#define RTL8366RB_EB_PREIFG_MASK (1 << RTL8366RB_EB_PREIFG_OFFSET)
+
+#define RTL8366RB_BDTH_SW_MAX 1048512
+#define RTL8366RB_BDTH_UNIT 64
+#define RTL8366RB_BDTH_REG_DEFAULT 16383
+
+/* QOS */
+#define RTL8366RB_QOS_BIT 15
+#define RTL8366RB_QOS_MASK (1 << RTL8366RB_QOS_BIT)
+/* Include/Exclude Preamble and IFG (20 bytes). 0:Exclude, 1:Include. */
+#define RTL8366RB_QOS_DEFAULT_PREIFG 1
+
+/* Interrupt handling */
+#define RTL8366RB_INTERRUPT_CONTROL_REG 0x0440
+#define RTL8366RB_INTERRUPT_POLARITY BIT(0)
+#define RTL8366RB_INTERRUPT_MASK_REG 0x0441
+#define RTL8366RB_INTERRUPT_LINK_CHGALL GENMASK(11, 0)
+#define RTL8366RB_INTERRUPT_ACLEXCEED BIT(8)
+#define RTL8366RB_INTERRUPT_STORMEXCEED BIT(9)
+#define RTL8366RB_INTERRUPT_P4_FIBER BIT(12)
+#define RTL8366RB_INTERRUPT_P4_UTP BIT(13)
+#define RTL8366RB_INTERRUPT_VALID (RTL8366RB_INTERRUPT_LINK_CHGALL | \
+ RTL8366RB_INTERRUPT_ACLEXCEED | \
+ RTL8366RB_INTERRUPT_STORMEXCEED | \
+ RTL8366RB_INTERRUPT_P4_FIBER | \
+ RTL8366RB_INTERRUPT_P4_UTP)
+#define RTL8366RB_INTERRUPT_STATUS_REG 0x0442
+
+/* bits 0..5 enable force when cleared */
+#define RTL8366RB_MAC_FORCE_CTRL_REG 0x0F11
+
+#define RTL8366RB_GREEN_FEATURE_REG 0x0F51
+#define RTL8366RB_GREEN_FEATURE_MSK 0x0007
+#define RTL8366RB_GREEN_FEATURE_TX BIT(0)
+#define RTL8366RB_GREEN_FEATURE_RX BIT(2)
+
+static struct rtl8366_mib_counter rtl8366rb_mib_counters[] = {
+ { 0, 0, 4, "IfInOctets" },
+ { 0, 4, 4, "EtherStatsOctets" },
+ { 0, 8, 2, "EtherStatsUnderSizePkts" },
+ { 0, 10, 2, "EtherFragments" },
+ { 0, 12, 2, "EtherStatsPkts64Octets" },
+ { 0, 14, 2, "EtherStatsPkts65to127Octets" },
+ { 0, 16, 2, "EtherStatsPkts128to255Octets" },
+ { 0, 18, 2, "EtherStatsPkts256to511Octets" },
+ { 0, 20, 2, "EtherStatsPkts512to1023Octets" },
+ { 0, 22, 2, "EtherStatsPkts1024to1518Octets" },
+ { 0, 24, 2, "EtherOversizeStats" },
+ { 0, 26, 2, "EtherStatsJabbers" },
+ { 0, 28, 2, "IfInUcastPkts" },
+ { 0, 30, 2, "EtherStatsMulticastPkts" },
+ { 0, 32, 2, "EtherStatsBroadcastPkts" },
+ { 0, 34, 2, "EtherStatsDropEvents" },
+ { 0, 36, 2, "Dot3StatsFCSErrors" },
+ { 0, 38, 2, "Dot3StatsSymbolErrors" },
+ { 0, 40, 2, "Dot3InPauseFrames" },
+ { 0, 42, 2, "Dot3ControlInUnknownOpcodes" },
+ { 0, 44, 4, "IfOutOctets" },
+ { 0, 48, 2, "Dot3StatsSingleCollisionFrames" },
+ { 0, 50, 2, "Dot3StatMultipleCollisionFrames" },
+ { 0, 52, 2, "Dot3sDeferredTransmissions" },
+ { 0, 54, 2, "Dot3StatsLateCollisions" },
+ { 0, 56, 2, "EtherStatsCollisions" },
+ { 0, 58, 2, "Dot3StatsExcessiveCollisions" },
+ { 0, 60, 2, "Dot3OutPauseFrames" },
+ { 0, 62, 2, "Dot1dBasePortDelayExceededDiscards" },
+ { 0, 64, 2, "Dot1dTpPortInDiscards" },
+ { 0, 66, 2, "IfOutUcastPkts" },
+ { 0, 68, 2, "IfOutMulticastPkts" },
+ { 0, 70, 2, "IfOutBroadcastPkts" },
+};
+
+static int rtl8366rb_get_mib_counter(struct realtek_smi *smi,
+ int port,
+ struct rtl8366_mib_counter *mib,
+ u64 *mibvalue)
+{
+ u32 addr, val;
+ int ret;
+ int i;
+
+ addr = RTL8366RB_MIB_COUNTER_BASE +
+ RTL8366RB_MIB_COUNTER_PORT_OFFSET * (port) +
+ mib->offset;
+
+ /*
+ * Writing access counter address first
+ * then ASIC will prepare 64bits counter wait for being retrived
+ */
+ ret = regmap_write(smi->map, addr, 0); /* Write whatever */
+ if (ret)
+ return ret;
+
+ /* Read MIB control register */
+ ret = regmap_read(smi->map, RTL8366RB_MIB_CTRL_REG, &val);
+ if (ret)
+ return -EIO;
+
+ if (val & RTL8366RB_MIB_CTRL_BUSY_MASK)
+ return -EBUSY;
+
+ if (val & RTL8366RB_MIB_CTRL_RESET_MASK)
+ return -EIO;
+
+ /*
+ * Read each individual MIB 16 bits at the time
+ */
+ *mibvalue = 0;
+ for (i = mib->length; i > 0; i--) {
+ ret = regmap_read(smi->map, addr + (i - 1), &val);
+ if (ret)
+ return ret;
+ *mibvalue = (*mibvalue << 16) | (val & 0xFFFF);
+ }
+ return 0;
+}
+
+static u32 rtl8366rb_get_irqmask(struct irq_data *d)
+{
+ int line = irqd_to_hwirq(d);
+ u32 val;
+
+ /*
+ * For line interrupts we combine link down in bits
+ * 6..11 with link up in bits 0..5 into one interrupt.
+ */
+ if (line < 12)
+ val = BIT(line) | BIT(line+6);
+ else
+ val = BIT(line);
+ return val;
+}
+
+static void rtl8366rb_mask_irq(struct irq_data *d)
+{
+ struct realtek_smi *smi = irq_data_get_irq_chip_data(d);
+ int ret;
+
+ ret = regmap_update_bits(smi->map, RTL8366RB_INTERRUPT_MASK_REG,
+ rtl8366rb_get_irqmask(d), 0);
+ if (ret)
+ dev_err(smi->dev, "could not mask IRQ\n");
+}
+
+static void rtl8366rb_unmask_irq(struct irq_data *d)
+{
+ struct realtek_smi *smi = irq_data_get_irq_chip_data(d);
+ int ret;
+
+ ret = regmap_update_bits(smi->map, RTL8366RB_INTERRUPT_MASK_REG,
+ rtl8366rb_get_irqmask(d),
+ rtl8366rb_get_irqmask(d));
+ if (ret)
+ dev_err(smi->dev, "could not unmask IRQ\n");
+}
+
+static irqreturn_t rtl8366rb_irq(int irq, void *data)
+{
+ struct realtek_smi *smi = data;
+ u32 stat;
+ int ret;
+
+ /* This clears the IRQ status register */
+ ret = regmap_read(smi->map, RTL8366RB_INTERRUPT_STATUS_REG,
+ &stat);
+ if (ret) {
+ dev_err(smi->dev, "can't read interrupt status\n");
+ return IRQ_NONE;
+ }
+ stat &= RTL8366RB_INTERRUPT_VALID;
+ if (!stat)
+ return IRQ_NONE;
+ while (stat) {
+ int line = __ffs(stat);
+ int child_irq;
+
+ stat &= ~BIT(line);
+ /*
+ * For line interrupts we combine link down in bits
+ * 6..11 with link up in bits 0..5 into one interrupt.
+ */
+ if (line < 12 && line > 5)
+ line -= 5;
+ child_irq = irq_find_mapping(smi->irqdomain, line);
+ handle_nested_irq(child_irq);
+ }
+ return IRQ_HANDLED;
+}
+
+static struct irq_chip rtl8366rb_irq_chip = {
+ .name = "RTL8366RB",
+ .irq_mask = rtl8366rb_mask_irq,
+ .irq_unmask = rtl8366rb_unmask_irq,
+};
+
+static int rtl8366rb_irq_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_data(irq, domain->host_data);
+ irq_set_chip_and_handler(irq, &rtl8366rb_irq_chip, handle_simple_irq);
+ irq_set_nested_thread(irq, 1);
+ irq_set_noprobe(irq);
+
+ return 0;
+}
+
+static void rtl8366rb_irq_unmap(struct irq_domain *d, unsigned int irq)
+{
+ irq_set_nested_thread(irq, 0);
+ irq_set_chip_and_handler(irq, NULL, NULL);
+ irq_set_chip_data(irq, NULL);
+}
+
+static const struct irq_domain_ops rtl8366rb_irqdomain_ops = {
+ .map = rtl8366rb_irq_map,
+ .unmap = rtl8366rb_irq_unmap,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+static int rtl8366rb_setup_cascaded_irq(struct realtek_smi *smi)
+{
+ struct device_node *intc = of_get_child_by_name(smi->dev->of_node,
+ "interrupt-controller");
+ unsigned long irq_trig;
+ int irq;
+ int ret;
+ u32 val;
+ int i;
+
+ if (!intc) {
+ dev_err(smi->dev, "missing child interrupt-controller node\n");
+ return -EINVAL;
+ }
+ /* RB8366RB IRQs cascade off this one */
+ irq = of_irq_get(intc, 0);
+ if (irq <= 0) {
+ dev_err(smi->dev, "failed to get parent IRQ\n");
+ return irq ?: -EINVAL;
+ }
+
+ /* This clears the IRQ status register */
+ ret = regmap_read(smi->map, RTL8366RB_INTERRUPT_STATUS_REG,
+ &val);
+ if (ret) {
+ dev_err(smi->dev, "can't read interrupt status\n");
+ return ret;
+ }
+
+ /* Fetch IRQ edge information from the descriptor */
+ irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq));
+ switch (irq_trig) {
+ case IRQF_TRIGGER_RISING:
+ case IRQF_TRIGGER_HIGH:
+ dev_info(smi->dev, "active high/rising IRQ\n");
+ val = 0;
+ break;
+ case IRQF_TRIGGER_FALLING:
+ case IRQF_TRIGGER_LOW:
+ dev_info(smi->dev, "active low/falling IRQ\n");
+ val = RTL8366RB_INTERRUPT_POLARITY;
+ break;
+ };
+ ret = regmap_update_bits(smi->map, RTL8366RB_INTERRUPT_CONTROL_REG,
+ RTL8366RB_INTERRUPT_POLARITY,
+ val);
+ if (ret) {
+ dev_err(smi->dev, "could not configure IRQ polarity\n");
+ return ret;
+ }
+
+ ret = devm_request_threaded_irq(smi->dev, irq, NULL,
+ rtl8366rb_irq, IRQF_ONESHOT,
+ "RTL8366RB", smi);
+ if (ret) {
+ dev_err(smi->dev, "unable to request irq: %d\n", ret);
+ return ret;
+ }
+ smi->irqdomain = irq_domain_add_linear(intc, smi->num_ports,
+ &rtl8366rb_irqdomain_ops, smi);
+ if (!smi->irqdomain) {
+ dev_err(smi->dev, "failed to create IRQ domain\n");
+ return -EINVAL;
+ }
+ for (i = 0; i < smi->num_ports; i++)
+ irq_set_parent(irq_create_mapping(smi->irqdomain, i), irq);
+
+ return 0;
+}
+
+/*
+ * This jam table activates "green ethernet", which means low power mode
+ * and is claimed to detect the cable length and not use more power than
+ * necessary, and the ports should enter power saving mode 10 seconds after
+ * a cable is disconnected.
+ */
+static const u32 rtl8366rb_green_jam[][2] = {
+ {0xBE78, 0x323C},
+ {0xBE77, 0x5000},
+ {0xBE2E, 0x7BA7},
+ {0xBE59, 0x3459},
+ {0xBE5A, 0x745A},
+ {0xBE5B, 0x785C},
+ {0xBE5C, 0x785C},
+ {0xBE6E, 0xE120},
+ {0xBE79, 0x323C},
+};
+
+static int rtl8366rb_setup(struct dsa_switch *ds)
+{
+ struct realtek_smi *smi = ds->priv;
+ u32 chip_id = 0;
+ u32 chip_ver = 0;
+ u32 val;
+ int ret;
+ int i;
+
+ ret = regmap_read(smi->map, RTL8366RB_CHIP_ID_REG, &chip_id);
+ if (ret) {
+ dev_err(smi->dev, "unable to read chip id\n");
+ return ret;
+ }
+
+ switch (chip_id) {
+ case RTL8366RB_CHIP_ID_8366:
+ break;
+ default:
+ dev_err(smi->dev, "unknown chip id (%04x)\n", chip_id);
+ return -ENODEV;
+ }
+
+ ret = regmap_read(smi->map, RTL8366RB_CHIP_VERSION_CTRL_REG,
+ &chip_ver);
+ if (ret) {
+ dev_err(smi->dev, "unable to read chip version\n");
+ return ret;
+ }
+
+ dev_info(smi->dev, "RTL%04x ver %u chip found\n",
+ chip_id, chip_ver & RTL8366RB_CHIP_VERSION_MASK);
+
+ /* Set up the "green ethernet" feature */
+ i = 0;
+ while (i < ARRAY_SIZE(rtl8366rb_green_jam)) {
+ ret = regmap_read(smi->map, RTL8366RB_PHY_ACCESS_BUSY_REG,
+ &val);
+ if (ret)
+ return ret;
+ if (!(val & RTL8366RB_PHY_INT_BUSY)) {
+ ret = regmap_write(smi->map,
+ RTL8366RB_PHY_ACCESS_CTRL_REG,
+ RTL8366RB_PHY_CTRL_WRITE);
+ if (ret)
+ return ret;
+ ret = regmap_write(smi->map,
+ rtl8366rb_green_jam[i][0],
+ rtl8366rb_green_jam[i][1]);
+ if (ret)
+ return ret;
+ i++;
+ }
+ }
+ ret = regmap_write(smi->map,
+ RTL8366RB_GREEN_FEATURE_REG,
+ (chip_ver == 1) ? 0x0007 : 0x0003);
+ if (ret)
+ return ret;
+ /*
+ * The RTL8366RB PHY driver will set up the PHY registers for power
+ * saving mode.
+ */
+
+ /* Force the fixed CPU port into 1Gbit mode, no autonegotiation */
+ ret = regmap_update_bits(smi->map, RTL8366RB_MAC_FORCE_CTRL_REG,
+ BIT(5), 0);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(smi->map, RTL8366RB_PAACR2,
+ 0xFF00U,
+ RTL8366RB_PAACR_CPU_PORT << 8);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(smi->map, RTL8366RB_MAC_FORCE_CTRL_REG,
+ BIT(5), BIT(5));
+ if (ret)
+ return ret;
+
+ /* Vendor driver sets 0x240 in registers 0xc and 0xd (undocumented) */
+ ret = regmap_write(smi->map, 0x0c, 0x240);
+ if (ret)
+ return ret;
+ ret = regmap_write(smi->map, 0x0d, 0x240);
+ if (ret)
+ return ret;
+
+ /*
+ * FIXME: this disables inserting the custom tag, enable this when we
+ * support the custom tag in net/dsa.
+ */
+ ret = regmap_update_bits(smi->map, RTL8368RB_CPU_CTRL_REG,
+ 0xFFFF, BIT(smi->cpu_port));
+
+ /* Make sure we default-enable the fixed CPU port */
+ ret = regmap_update_bits(smi->map, RTL8366RB_PECR,
+ BIT(smi->cpu_port),
+ 0);
+
+ /* set maximum packet length to 1536 bytes */
+ ret = regmap_update_bits(smi->map, RTL8366RB_SGCR,
+ RTL8366RB_SGCR_MAX_LENGTH_MASK,
+ RTL8366RB_SGCR_MAX_LENGTH_1536);
+ if (ret)
+ return ret;
+
+ /* enable learning for all ports */
+ ret = regmap_write(smi->map, RTL8366RB_SSCR0, 0);
+ if (ret)
+ return ret;
+
+ /* enable auto ageing for all ports */
+ ret = regmap_write(smi->map, RTL8366RB_SSCR1, 0);
+ if (ret)
+ return ret;
+
+ /*
+ * discard VLAN tagged packets if the port is not a member of
+ * the VLAN with which the packets is associated.
+ */
+ ret = regmap_write(smi->map, RTL8366RB_VLAN_INGRESS_CTRL2_REG,
+ RTL8366RB_PORT_ALL);
+ if (ret)
+ return ret;
+
+ /* don't drop packets whose DA has not been learned */
+ ret = regmap_update_bits(smi->map, RTL8366RB_SSCR2,
+ RTL8366RB_SSCR2_DROP_UNKNOWN_DA, 0);
+ if (ret)
+ return ret;
+
+ /* Issues reset_vlan(), enable_vlan(true) */
+ ret = rtl8366_init_vlan(smi);
+ if (ret)
+ return ret;
+
+ ret = rtl8366rb_setup_cascaded_irq(smi);
+ if (ret)
+ dev_info(smi->dev, "no interrupt support\n");
+
+ return 0;
+}
+
+static int rtl8366rb_set_addr(struct dsa_switch *ds, u8 *addr)
+{
+ struct realtek_smi *smi = ds->priv;
+ u16 val;
+ int ret;
+
+ dev_info(smi->dev, "set MAC: %02X:%02X:%02X:%02X:%02X:%02X\n",
+ addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]);
+ val = addr[0] << 8 | addr[1];
+ ret = regmap_write(smi->map, RTL8366RB_SMAR0, val);
+ if (ret)
+ return ret;
+ val = addr[2] << 8 | addr[3];
+ ret = regmap_write(smi->map, RTL8366RB_SMAR1, val);
+ if (ret)
+ return ret;
+ val = addr[4] << 8 | addr[5];
+ ret = regmap_write(smi->map, RTL8366RB_SMAR2, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8366rb_phy_read(struct dsa_switch *ds, int phy, int regnum)
+{
+ struct realtek_smi *smi = ds->priv;
+ u32 val;
+ u32 reg;
+ int ret;
+
+ if (phy > RTL8366RB_PHY_NO_MAX)
+ return -EINVAL;
+
+ ret = regmap_write(smi->map, RTL8366RB_PHY_ACCESS_CTRL_REG,
+ RTL8366RB_PHY_CTRL_READ);
+ if (ret)
+ return ret;
+
+ reg = 0x8000 | (1 << (phy + RTL8366RB_PHY_NO_OFFSET)) | regnum;
+
+ ret = regmap_write(smi->map, reg, 0);
+ if (ret) {
+ dev_err(smi->dev,
+ "failed to write PHY%d reg %04x @ %04x, ret %d\n",
+ phy, regnum, reg, ret);
+ return ret;
+ }
+
+ ret = regmap_read(smi->map, RTL8366RB_PHY_ACCESS_DATA_REG, &val);
+ if (ret)
+ return ret;
+
+ dev_dbg(smi->dev, "read PHY%d register 0x%04x @ %08x, val <- %04x\n",
+ phy, regnum, reg, val);
+
+ return val;
+}
+
+static int rtl8366rb_phy_write(struct dsa_switch *ds, int phy, int regnum,
+ u16 val)
+{
+ struct realtek_smi *smi = ds->priv;
+ u32 reg;
+ int ret;
+
+ if (phy > RTL8366RB_PHY_NO_MAX)
+ return -EINVAL;
+
+ ret = regmap_write(smi->map, RTL8366RB_PHY_ACCESS_CTRL_REG,
+ RTL8366RB_PHY_CTRL_WRITE);
+ if (ret)
+ return ret;
+
+ reg = 0x8000 | (1 << (phy + RTL8366RB_PHY_NO_OFFSET)) | regnum;
+
+ dev_dbg(smi->dev, "write PHY%d register 0x%04x @ %04x, val -> %04x\n",
+ phy, regnum, reg, val);
+
+ ret = regmap_write(smi->map, reg, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static enum dsa_tag_protocol rtl8366_get_tag_protocol(struct dsa_switch *ds)
+{
+ /* FIXME: implement the right tagging protocol */
+ return DSA_TAG_PROTO_NONE;
+}
+
+static void rtl8366rb_adjust_link(struct dsa_switch *ds, int port,
+ struct phy_device *phydev)
+{
+ struct realtek_smi *smi = ds->priv;
+
+ if (port == smi->cpu_port) {
+ dev_info(smi->dev, "adjust link on CPU port\n");
+ }
+}
+
+static int
+rtl8366rb_port_enable(struct dsa_switch *ds, int port,
+ struct phy_device *phy)
+{
+ struct realtek_smi *smi = ds->priv;
+
+ dev_info(smi->dev, "enable port %d\n", port);
+ return regmap_update_bits(smi->map, RTL8366RB_PECR, BIT(port),
+ 0);
+
+}
+
+static void
+rtl8366rb_port_disable(struct dsa_switch *ds, int port,
+ struct phy_device *phy)
+{
+ struct realtek_smi *smi = ds->priv;
+
+ dev_info(smi->dev, "disable port %d\n", port);
+ regmap_update_bits(smi->map, RTL8366RB_PECR, BIT(port),
+ BIT(port));
+}
+
+static int rtl8366rb_get_vlan_4k(struct realtek_smi *smi, u32 vid,
+ struct rtl8366_vlan_4k *vlan4k)
+{
+ u32 data[3];
+ int ret;
+ int i;
+
+ memset(vlan4k, '\0', sizeof(struct rtl8366_vlan_4k));
+
+ if (vid >= RTL8366RB_NUM_VIDS)
+ return -EINVAL;
+
+ /* write VID */
+ ret = regmap_write(smi->map, RTL8366RB_VLAN_TABLE_WRITE_BASE,
+ vid & RTL8366RB_VLAN_VID_MASK);
+ if (ret)
+ return ret;
+
+ /* write table access control word */
+ ret = regmap_write(smi->map, RTL8366RB_TABLE_ACCESS_CTRL_REG,
+ RTL8366RB_TABLE_VLAN_READ_CTRL);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < 3; i++) {
+ ret = regmap_read(smi->map,
+ RTL8366RB_VLAN_TABLE_READ_BASE + i,
+ &data[i]);
+ if (ret)
+ return ret;
+ }
+
+ vlan4k->vid = vid;
+ vlan4k->untag = (data[1] >> RTL8366RB_VLAN_UNTAG_SHIFT) &
+ RTL8366RB_VLAN_UNTAG_MASK;
+ vlan4k->member = data[1] & RTL8366RB_VLAN_MEMBER_MASK;
+ vlan4k->fid = data[2] & RTL8366RB_VLAN_FID_MASK;
+
+ return 0;
+}
+
+static int rtl8366rb_set_vlan_4k(struct realtek_smi *smi,
+ const struct rtl8366_vlan_4k *vlan4k)
+{
+ u32 data[3];
+ int ret;
+ int i;
+
+ if (vlan4k->vid >= RTL8366RB_NUM_VIDS ||
+ vlan4k->member > RTL8366RB_VLAN_MEMBER_MASK ||
+ vlan4k->untag > RTL8366RB_VLAN_UNTAG_MASK ||
+ vlan4k->fid > RTL8366RB_FIDMAX)
+ return -EINVAL;
+
+ data[0] = vlan4k->vid & RTL8366RB_VLAN_VID_MASK;
+ data[1] = (vlan4k->member & RTL8366RB_VLAN_MEMBER_MASK) |
+ ((vlan4k->untag & RTL8366RB_VLAN_UNTAG_MASK) <<
+ RTL8366RB_VLAN_UNTAG_SHIFT);
+ data[2] = vlan4k->fid & RTL8366RB_VLAN_FID_MASK;
+
+ for (i = 0; i < 3; i++) {
+ ret = regmap_write(smi->map,
+ RTL8366RB_VLAN_TABLE_WRITE_BASE + i,
+ data[i]);
+ if (ret)
+ return ret;
+ }
+
+ /* write table access control word */
+ ret = regmap_write(smi->map, RTL8366RB_TABLE_ACCESS_CTRL_REG,
+ RTL8366RB_TABLE_VLAN_WRITE_CTRL);
+
+ return ret;
+}
+
+static int rtl8366rb_get_vlan_mc(struct realtek_smi *smi, u32 index,
+ struct rtl8366_vlan_mc *vlanmc)
+{
+ u32 data[3];
+ int ret;
+ int i;
+
+ memset(vlanmc, '\0', sizeof(struct rtl8366_vlan_mc));
+
+ if (index >= RTL8366RB_NUM_VLANS)
+ return -EINVAL;
+
+ for (i = 0; i < 3; i++) {
+ ret = regmap_read(smi->map,
+ RTL8366RB_VLAN_MC_BASE(index) + i,
+ &data[i]);
+ if (ret)
+ return ret;
+ }
+
+ vlanmc->vid = data[0] & RTL8366RB_VLAN_VID_MASK;
+ vlanmc->priority = (data[0] >> RTL8366RB_VLAN_PRIORITY_SHIFT) &
+ RTL8366RB_VLAN_PRIORITY_MASK;
+ vlanmc->untag = (data[1] >> RTL8366RB_VLAN_UNTAG_SHIFT) &
+ RTL8366RB_VLAN_UNTAG_MASK;
+ vlanmc->member = data[1] & RTL8366RB_VLAN_MEMBER_MASK;
+ vlanmc->fid = data[2] & RTL8366RB_VLAN_FID_MASK;
+
+ return 0;
+}
+
+static int rtl8366rb_set_vlan_mc(struct realtek_smi *smi, u32 index,
+ const struct rtl8366_vlan_mc *vlanmc)
+{
+ u32 data[3];
+ int ret;
+ int i;
+
+ if (index >= RTL8366RB_NUM_VLANS ||
+ vlanmc->vid >= RTL8366RB_NUM_VIDS ||
+ vlanmc->priority > RTL8366RB_PRIORITYMAX ||
+ vlanmc->member > RTL8366RB_VLAN_MEMBER_MASK ||
+ vlanmc->untag > RTL8366RB_VLAN_UNTAG_MASK ||
+ vlanmc->fid > RTL8366RB_FIDMAX)
+ return -EINVAL;
+
+ data[0] = (vlanmc->vid & RTL8366RB_VLAN_VID_MASK) |
+ ((vlanmc->priority & RTL8366RB_VLAN_PRIORITY_MASK) <<
+ RTL8366RB_VLAN_PRIORITY_SHIFT);
+ data[1] = (vlanmc->member & RTL8366RB_VLAN_MEMBER_MASK) |
+ ((vlanmc->untag & RTL8366RB_VLAN_UNTAG_MASK) <<
+ RTL8366RB_VLAN_UNTAG_SHIFT);
+ data[2] = vlanmc->fid & RTL8366RB_VLAN_FID_MASK;
+
+ for (i = 0; i < 3; i++) {
+ ret = regmap_write(smi->map,
+ RTL8366RB_VLAN_MC_BASE(index) + i,
+ data[i]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int rtl8366rb_get_mc_index(struct realtek_smi *smi, int port, int *val)
+{
+ u32 data;
+ int ret;
+
+ if (port >= smi->num_ports)
+ return -EINVAL;
+
+ ret = regmap_read(smi->map, RTL8366RB_PORT_VLAN_CTRL_REG(port),
+ &data);
+ if (ret)
+ return ret;
+
+ *val = (data >> RTL8366RB_PORT_VLAN_CTRL_SHIFT(port)) &
+ RTL8366RB_PORT_VLAN_CTRL_MASK;
+
+ return 0;
+
+}
+
+static int rtl8366rb_set_mc_index(struct realtek_smi *smi, int port, int index)
+{
+ if (port >= smi->num_ports || index >= RTL8366RB_NUM_VLANS)
+ return -EINVAL;
+
+ return regmap_update_bits(smi->map, RTL8366RB_PORT_VLAN_CTRL_REG(port),
+ RTL8366RB_PORT_VLAN_CTRL_MASK <<
+ RTL8366RB_PORT_VLAN_CTRL_SHIFT(port),
+ (index & RTL8366RB_PORT_VLAN_CTRL_MASK) <<
+ RTL8366RB_PORT_VLAN_CTRL_SHIFT(port));
+}
+
+static bool rtl8366rb_is_vlan_valid(struct realtek_smi *smi, unsigned vlan)
+{
+ unsigned max = RTL8366RB_NUM_VLANS;
+
+ if (smi->vlan4k_enabled)
+ max = RTL8366RB_NUM_VIDS - 1;
+
+ if (vlan == 0 || vlan >= max)
+ return 0;
+
+ return 1;
+}
+
+static int rtl8366rb_enable_vlan(struct realtek_smi *smi, bool enable)
+{
+ return regmap_update_bits(smi->map, RTL8366RB_SGCR,
RTL8366RB_SGCR_EN_VLAN,
+ enable ? RTL8366RB_SGCR_EN_VLAN : 0);
+}
+
+static int rtl8366rb_enable_vlan4k(struct realtek_smi *smi, bool enable)
+{
+ return regmap_update_bits(smi->map, RTL8366RB_SGCR,
+ RTL8366RB_SGCR_EN_VLAN_4KTB,
+ enable ? RTL8366RB_SGCR_EN_VLAN_4KTB : 0);
+}
+
+static int rtl8366rb_reset_chip(struct realtek_smi *smi)
+{
+ int timeout = 10;
+ u32 val;
+ int ret;
+
+ realtek_smi_write_reg_noack(smi, RTL8366RB_RESET_CTRL_REG,
+ RTL8366RB_CHIP_CTRL_RESET_HW);
+ do {
+ msleep(1);
+ ret = regmap_read(smi->map, RTL8366RB_RESET_CTRL_REG, &val);
+ if (ret)
+ return ret;
+
+ if (!(val & RTL8366RB_CHIP_CTRL_RESET_HW))
+ break;
+ } while (--timeout);
+
+ if (!timeout) {
+ dev_err(smi->dev, "timeout waiting for the switch to reset\n");
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int rtl8366rb_detect(struct realtek_smi *smi)
+{
+ struct device *dev = smi->dev;
+ int ret;
+ u32 val;
+
+ /* Detect device */
+ ret = regmap_read(smi->map, 0x5c, &val);
+ if (ret) {
+ dev_err(dev, "can't get chip ID (%d)\n", ret);
+ return ret;
+ }
+
+ switch(val) {
+ case 0x6027:
+ dev_info(dev, "found an RTL8366S switch\n");
+ dev_err(dev, "this switch is not yet supported, submit
patches!\n");
+ return -ENODEV;
+ break;
+ case 0x5937:
+ dev_info(dev, "found an RTL8366RB switch\n");
+ smi->cpu_port = RTL8366RB_PORT_NUM_CPU;
+ smi->num_ports = RTL8366RB_NUM_PORTS;
+ smi->num_vlan_mc = RTL8366RB_NUM_VLANS;
+ smi->mib_counters = rtl8366rb_mib_counters;
+ smi->num_mib_counters = ARRAY_SIZE(rtl8366rb_mib_counters);
+ break;
+ default:
+ dev_info(dev, "found an Unknown Realtek switch (id=0x%04x)\n",
+ val);
+ break;
+ }
+
+ ret = rtl8366rb_reset_chip(smi);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static const struct dsa_switch_ops rtl8366rb_switch_ops = {
+ .get_tag_protocol = rtl8366_get_tag_protocol,
+ .setup = rtl8366rb_setup,
+ .set_addr = rtl8366rb_set_addr,
+ .adjust_link = rtl8366rb_adjust_link,
+ .get_strings = rtl8366_get_strings,
+ .get_ethtool_stats = rtl8366_get_ethtool_stats,
+ .get_sset_count = rtl8366_get_sset_count,
+ .port_vlan_filtering = rtl8366_vlan_filtering,
+ .port_vlan_prepare = rtl8366_vlan_prepare,
+ .port_vlan_add = rtl8366_vlan_add,
+ .port_vlan_del = rtl8366_vlan_del,
+ .phy_read = rtl8366rb_phy_read,
+ .phy_write = rtl8366rb_phy_write,
+ .port_enable = rtl8366rb_port_enable,
+ .port_disable = rtl8366rb_port_disable,
+};
+
+static const struct realtek_smi_ops rtl8366rb_smi_ops = {
+ .detect = rtl8366rb_detect,
+ .get_vlan_mc = rtl8366rb_get_vlan_mc,
+ .set_vlan_mc = rtl8366rb_set_vlan_mc,
+ .get_vlan_4k = rtl8366rb_get_vlan_4k,
+ .set_vlan_4k = rtl8366rb_set_vlan_4k,
+ .get_mc_index = rtl8366rb_get_mc_index,
+ .set_mc_index = rtl8366rb_set_mc_index,
+ .get_mib_counter = rtl8366rb_get_mib_counter,
+ .is_vlan_valid = rtl8366rb_is_vlan_valid,
+ .enable_vlan = rtl8366rb_enable_vlan,
+ .enable_vlan4k = rtl8366rb_enable_vlan4k,
+};
+
+const struct realtek_smi_variant rtl8366rb_variant = {
+ .ds_ops = &rtl8366rb_switch_ops,
+ .ops = &rtl8366rb_smi_ops,
+ .clk_delay = 10,
+ .cmd_read = 0xa9,
+ .cmd_write = 0xa8,
+};
+EXPORT_SYMBOL_GPL(rtl8366rb_variant);
--
2.13.6
