Hi Leon, -----Original Message----- > From: Leon Romanovsky [mailto:[email protected]] > Sent: Monday, August 21, 2017 11:32 AM > To: Salil Mehta > Cc: [email protected]; Zhuangyuzeng (Yisen); lipeng (Y); > [email protected]; [email protected]; linux- > [email protected]; [email protected]; Linuxarm > Subject: Re: [PATCH V3 net-next] net: hns3: Add support to change MTU > in HNS3 hardware > > On Mon, Aug 21, 2017 at 11:12:23AM +0100, Salil Mehta wrote: > > This patch adds the following support to the HNS3 driver: > > 1. Support to change the Maximum Transmission Unit of a > > of a port in the HNS NIC hardware. Typo-->Will also delete duplicate 'of a'
> > 2. Initializes the supported MTU range for the netdevice. > > > > Signed-off-by: lipeng <[email protected]> > > Signed-off-by: Salil Mehta <[email protected]> > > --- > > PATCH V3: Addressed some minor comments Leon Romanovsky > > 1. https://lkml.org/lkml/2017/8/20/27 > > PATCH V2: Addresses comments given by Andrew Lunn > > 1. https://lkml.org/lkml/2017/8/18/282 > > PATCH V1: Initial Submit > > --- > > .../net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c | 36 > ++++++++++++++++++++++ > > .../net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.h | 1 + > > 2 files changed, 37 insertions(+) > > > > diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c > b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c > > index e731f87..c087a9f 100644 > > --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c > > +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c > > @@ -1278,11 +1278,44 @@ static int hns3_ndo_set_vf_vlan(struct > net_device *netdev, int vf, u16 vlan, > > return ret; > > } > > > > +static int hns3_nic_change_mtu(struct net_device *netdev, int > new_mtu) > > +{ > > + struct hns3_nic_priv *priv = netdev_priv(netdev); > > + struct hnae3_handle *h = priv->ae_handle; > > + bool if_running = netif_running(netdev); > > + int ret; > > + > > + if (!h->ae_algo->ops->set_mtu) > > + return -ENOTSUPP; > > Sorry for not spotting this before, but it should be -EOPNOTSUPP and > not -ENOTSUPP. Yes, Maybe I should have seen it earlier as well :( I Will rectify this. Thanks > > > + > > + /* if this was called with netdev up then bring netdevice down */ > > + if (if_running) { > > + (void)hns3_nic_net_stop(netdev); > > + msleep(100); > > + } > > + > > + ret = h->ae_algo->ops->set_mtu(h, new_mtu); > > + if (ret) { > > + netdev_err(netdev, "failed to change MTU in hardware %d\n", > > + ret); > > + return ret; > > + } > > + > > + /* if the netdev was running earlier, bring it up again */ > > + if (if_running) { > > + if (hns3_nic_net_open(netdev)) > > + ret = -EINVAL; > > + } > > Anyway, you will resubmit because of wrong error code. > if (if_running && hns3_nic_net_open(netdev)) > ret = -EINVAL > > Thanks > > > + > > + return ret; > > +} > > + > > static const struct net_device_ops hns3_nic_netdev_ops = { > > .ndo_open = hns3_nic_net_open, > > .ndo_stop = hns3_nic_net_stop, > > .ndo_start_xmit = hns3_nic_net_xmit, > > .ndo_set_mac_address = hns3_nic_net_set_mac_address, > > + .ndo_change_mtu = hns3_nic_change_mtu, > > .ndo_set_features = hns3_nic_set_features, > > .ndo_get_stats64 = hns3_nic_get_stats64, > > .ndo_setup_tc = hns3_nic_setup_tc, > > @@ -2752,6 +2785,9 @@ static int hns3_client_init(struct hnae3_handle > *handle) > > goto out_reg_netdev_fail; > > } > > > > + /* MTU range: (ETH_MIN_MTU(kernel default) - 9706) */ > > + netdev->max_mtu = HNS3_MAX_MTU - (ETH_HLEN + ETH_FCS_LEN + > VLAN_HLEN); > > + > > return ret; > > > > out_reg_netdev_fail: > > diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.h > b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.h > > index a6e8f15..7e87461 100644 > > --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.h > > +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.h > > @@ -76,6 +76,7 @@ enum hns3_nic_state { > > #define HNS3_RING_NAME_LEN 16 > > #define HNS3_BUFFER_SIZE_2048 2048 > > #define HNS3_RING_MAX_PENDING 32768 > > +#define HNS3_MAX_MTU 9728 > > > > #define HNS3_BD_SIZE_512_TYPE 0 > > #define HNS3_BD_SIZE_1024_TYPE 1 > > -- > > 2.7.4 > > > > > > -- > > To unsubscribe from this list: send the line "unsubscribe linux-rdma" > in > > the body of a message to [email protected] > > More majordomo info at http://vger.kernel.org/majordomo-info.html
