Linsys Contractor Amit S. Kale wrote:
+/**
+ * netxen_nic_set_multi - Multicast
+ **/
+void netxen_nic_set_multi(struct net_device *netdev)
+{
+ struct netxen_port *port = netdev_priv(netdev);
+ struct dev_mc_list *mc_ptr;
+
+ mc_ptr = netdev->mc_list;
+ if (netdev->flags & IFF_PROMISC)
+ netxen_nic_set_promisc_mode(port);
+ else
+ netxen_nic_unset_promisc_mode(port);
+}
This appears unfinished, it does not handle multicast at all.
+int netxen_nic_change_mtu(struct net_device *netdev, int new_mtu)
+{
+ struct netxen_port *port = netdev_priv(netdev);
+
+ if (new_mtu & 0xffff0000)
+ return -EINVAL;
+
+ if (new_mtu > 8000) {
please use named constants here, rather than magic numbers
+ printk(KERN_ERR "%s: %s MTU > 8000 is not supported\n",
+ netxen_nic_driver_name, netdev->name);
+ return -EINVAL;
+ }
+
+ netxen_nic_set_mtu(port, new_mtu);
+ netdev->mtu = new_mtu;
+
+ return 0;
+}
+
+/*
+ * check if the firmware has been downloaded and ready to run and
+ * setup the address for the descriptors in the adapter
+ */
ah hah! so you do have a firmware! Well, export that version via
ethtool...
+/*
+ * Changes the CRB window to the specified window.
+ */
+void netxen_nic_pci_change_crbwindow(struct netxen_adapter *adapter,
u32 wndw)
+{
+ struct netxen_pcix_crb_window window;
+ unsigned long offset;
+ u32 tmp;
+
+ if (adapter->curr_window == wndw)
+ return;
+
+ /*
+ * Move the CRB window.
+ * We need to write to the "direct access" region of PCI
+ * to avoid a race condition where the window register has
+ * not been successfully written across CRB before the target
+ * register address is received by PCI. The direct region bypasses
+ * the CRB bus.
+ */
+ offset = adapter->ahw.pci_base + NETXEN_PCIX_PH_REG(PCIX_CRB_WINDOW);
+
+ *(netxen_crbword_t *) & window = 0;
WTF is this code doing? It looks quite wrong...
+ window.addrbit = wndw;
+ writel(*(unsigned int *)&window, (void *)(offset));
bug: code is backwards. was this code ever tested?
+ /* MUST make sure window is set before we forge on... */
+ while ((tmp = readl((void *)offset)) != *(u32 *) & window)
+ printk(KERN_WARNING "%s: %s WARNING: CRB window value not "
+ "registered properly: 0x%08x.\n",
+ netxen_nic_driver_name, __FUNCTION__, tmp);
infinite printk loop.
+ adapter->curr_window = wndw;
+}
+
+/*
+ * Set the CRB window based on the offset.
+ */
+static inline unsigned long
+netxen_nic_pci_set_crbwindow(struct netxen_adapter *adapter, u64 off)
+{
+ /*
+ * See if we are currently pointing to the region we want to use next.
+ */
+
+ if ((off >= NETXEN_CRB_PCIX_HOST) && (off < NETXEN_CRB_DDR_NET)) {
+ /*
+ * No need to change window. PCIX and PCIE regs are in both
+ * windows.
+ */
+ return off;
+ }
+
+ if ((off >= NETXEN_CRB_PCIX_HOST) && (off < NETXEN_CRB_PCIX_HOST2)) {
+ /* We are in first CRB window */
+ if (adapter->curr_window != 0)
+ netxen_nic_pci_change_crbwindow(adapter, 0);
+
+ return off;
+ }
+
+ if ((off > NETXEN_CRB_PCIX_HOST2) && (off < NETXEN_CRB_MAX)) {
+ /* We are in second CRB window */
+ off = off - NETXEN_CRB_PCIX_HOST2 + NETXEN_CRB_PCIX_HOST;
+
+ if (adapter->curr_window != 1)
+ netxen_nic_pci_change_crbwindow(adapter, 1);
+
+ return off;
+ }
+
+ if ((off >= NETXEN_PCI_DIRECT_CRB) && (off < NETXEN_PCI_CAMQM_MAX)) {
+ /*
+ * We are in the QM or direct access register region - do
+ * nothing
+ */
+ return off;
+ }
+
+ /* strange address given */
+ dump_stack();
+ printk(KERN_WARNING
+ "%s: Warning: netxen_nic_pci_set_crbwindow called with"
+ " an unknown address(%llx)\n", netxen_nic_driver_name, off);
+
+ return off;
+}
+
+int
+netxen_nic_hw_write_wx(struct netxen_adapter *adapter, u64 off, void
*data,
+ int len)
+{
+ void *addr;
+ unsigned long flags = 0;
+
+ if (ADDR_IN_WINDOW1(off)) {
+ addr = NETXEN_CRB_NORMALIZE(adapter, off);
+ read_lock(&adapter->adapter_lock);
+ } else { /* Window 0 */
+ addr = (void *)(ptrdiff_t) (adapter->ahw.pci_base + off);
+ write_lock_irqsave(&adapter->adapter_lock, flags);
+ netxen_nic_pci_change_crbwindow(adapter, 0);
+ }
+
+ DPRINTK(INFO, "writing to base %lx offset %llx addr %p"
+ " data %llx len %d\n",
+ adapter->ahw.pci_base, off, addr,
+ *(unsigned long long *)data, len);
+ switch (len) {
+ case 1:
+ writeb(*(u8 *) data, addr);
+ break;
+ case 2:
+ writew(*(u16 *) data, addr);
+ break;
+ case 4:
+ writel(*(u32 *) data, addr);
+ break;
+ case 8:
+ writeq(*(u64 *) data, addr);
+ break;
+ default:
+ DPRINTK(INFO,
+ "writing data %lx to offset %llx, num words=%d\n",
+ *(unsigned long *)data, off, (len >> 3));
+
+ NETXEN_NIC_HW_BLOCK_WRITE_64(data, addr, (len >> 3));
+ break;
+ }
+ if (ADDR_IN_WINDOW1(off))
+ read_unlock(&adapter->adapter_lock);
+ else { /* Window 0 */
+ netxen_nic_pci_change_crbwindow(adapter, 1);
+ write_unlock_irqrestore(&adapter->adapter_lock, flags);
+ }
buggy locking? you read-lock when writing to registers.
+int
+netxen_nic_hw_read_wx(struct netxen_adapter *adapter, u64 off, void *data,
+ int len)
+{
+ void *addr;
+ unsigned long flags = 0;
+
+ if (ADDR_IN_WINDOW1(off)) { /* Window 1 */
+ addr = NETXEN_CRB_NORMALIZE(adapter, off);
+ read_lock(&adapter->adapter_lock);
+ } else { /* Window 0 */
+ addr = (void *)(ptrdiff_t) (adapter->ahw.pci_base + off);
+ write_lock_irqsave(&adapter->adapter_lock, flags);
+ netxen_nic_pci_change_crbwindow(adapter, 0);
+ }
+
+ DPRINTK(INFO, "reading from base %lx offset %llx addr %p\n",
+ adapter->ahw.pci_base, off, addr);
+ switch (len) {
+ case 1:
+ *(u8 *) data = readb(addr);
+ break;
+ case 2:
+ *(u16 *) data = readw(addr);
+ break;
+ case 4:
+ *(u32 *) data = readl(addr);
+ break;
+ case 8:
+ *(u64 *) data = readq(addr);
+ break;
+ default:
+ NETXEN_NIC_HW_BLOCK_READ_64(data, addr, (len >> 3));
+ break;
+ }
+ DPRINTK(INFO, "read %lx\n", *(unsigned long *)data);
+
+ if (ADDR_IN_WINDOW1(off))
+ read_unlock(&adapter->adapter_lock);
+ else { /* Window 0 */
+ netxen_nic_pci_change_crbwindow(adapter, 1);
+ write_unlock_irqrestore(&adapter->adapter_lock, flags);
+ }
+
+ return 0;
+}
+
+void netxen_nic_reg_write(struct netxen_adapter *adapter, u64 off, u32
val)
+{ /* Only for window 1 */
+ void *addr;
+
+ read_lock(&adapter->adapter_lock);
+
+ if (adapter->curr_window != 1)
+ netxen_nic_pci_change_crbwindow(adapter, 1);
+ addr = NETXEN_CRB_NORMALIZE(adapter, off);
+ DPRINTK(INFO, "writing to base %lx offset %llx addr %p data %x\n",
+ adapter->ahw.pci_base, off, addr, val);
+ writel(val, addr);
+
+ read_unlock(&adapter->adapter_lock);
+}
+
+int netxen_nic_reg_read(struct netxen_adapter *adapter, u64 off)
+{ /* Only for window 1 */
+ void *addr;
+ int val;
+
+ read_lock(&adapter->adapter_lock);
+ addr = NETXEN_CRB_NORMALIZE(adapter, off);
+ DPRINTK(INFO, "reading from base %lx offset %llx addr %p\n",
+ adapter->ahw.pci_base, off, addr);
+ val = readl(addr);
+ writel(val, addr);
+ read_unlock(&adapter->adapter_lock);
+
+ return val;
+}
+
+/* Change the window to 0, write and change back to window 1. */
+void netxen_nic_write_w0(struct netxen_adapter *adapter, u32 index, u32
value)
+{
+ unsigned long flags;
+ void *addr;
+
+ write_lock_irqsave(&adapter->adapter_lock, flags);
+ netxen_nic_pci_change_crbwindow(adapter, 0);
+ addr = (void *)(adapter->ahw.pci_base + index);
+ writel(value, addr);
+ netxen_nic_pci_change_crbwindow(adapter, 1);
+ write_unlock_irqrestore(&adapter->adapter_lock, flags);
+}
+
+/* Change the window to 0, read and change back to window 1. */
+void netxen_nic_read_w0(struct netxen_adapter *adapter, u32 index, u32
* value)
+{
+ unsigned long flags;
+ void *addr;
+
+ addr = (void *)(adapter->ahw.pci_base + index);
+
+ write_lock_irqsave(&adapter->adapter_lock, flags);
+ netxen_nic_pci_change_crbwindow(adapter, 0);
+ *value = readl(addr);
+ netxen_nic_pci_change_crbwindow(adapter, 1);
+ write_unlock_irqrestore(&adapter->adapter_lock, flags);
+}
highly sub-optimal, deadlock-prone locking.
every register read/write should not acquire a lock.
+static unsigned long
+netxen_nic_pci_set_window(unsigned long long pci_base, unsigned long
long addr)
+{
+ static int ddr_mn_window = -1;
+ static int qdr_sn_window = -1;
+ int window;
+
+ if (ADDR_IN_RANGE(addr, NETXEN_ADDR_DDR_NET,
NETXEN_ADDR_DDR_NET_MAX)) {
+ /* DDR network side */
+ addr -= NETXEN_ADDR_DDR_NET;
+ window = (addr >> 25) & 0x3ff;
+ if (ddr_mn_window != window) {
+ ddr_mn_window = window;
+ writel(window, (void *)(ptrdiff_t) (pci_base +
+ NETXEN_PCIX_PH_REG
+ (PCIX_MN_WINDOW)));
+ /* MUST make sure window is set before we forge on... */
+ readl((void *)(ptrdiff_t) (pci_base +
+ NETXEN_PCIX_PH_REG
+ (PCIX_MN_WINDOW)));
+ }
+ addr -= (window * 0x2000000);
+ addr += NETXEN_PCI_DDR_NET;
+ } else if (ADDR_IN_RANGE(addr, NETXEN_ADDR_OCM0,
NETXEN_ADDR_OCM0_MAX)) {
+ addr -= NETXEN_ADDR_OCM0;
+ addr += NETXEN_PCI_OCM0;
+ } else if (ADDR_IN_RANGE(addr, NETXEN_ADDR_OCM1,
NETXEN_ADDR_OCM1_MAX)) {
+ addr -= NETXEN_ADDR_OCM1;
+ addr += NETXEN_PCI_OCM1;
+ } else
+ if (ADDR_IN_RANGE
+ (addr, NETXEN_ADDR_QDR_NET, NETXEN_ADDR_QDR_NET_MAX)) {
+ /* QDR network side */
+ addr -= NETXEN_ADDR_QDR_NET;
+ window = (addr >> 22) & 0x3f;
+ if (qdr_sn_window != window) {
+ qdr_sn_window = window;
+ writel((window << 22),
+ (void *)(ptrdiff_t) (pci_base +
+ NETXEN_PCIX_PH_REG
+ (PCIX_SN_WINDOW)));
+ /* MUST make sure window is set before we forge on... */
+ readl((void *)(ptrdiff_t) (pci_base +
+ NETXEN_PCIX_PH_REG
+ (PCIX_SN_WINDOW)));
+ }
+ addr -= (window * 0x400000);
+ addr += NETXEN_PCI_QDR_NET;
+ } else {
+ /*
+ * peg gdb frequently accesses memory that doesn't exist,
+ * this limits the chit chat so debugging isn't slowed down.
+ */
+ if ((netxen_pci_set_window_warning_count++ < 8)
+ || (netxen_pci_set_window_warning_count % 64 == 0))
+ printk("%s: Warning:netxen_nic_pci_set_window()"
+ " Unknown address range!\n",
+ netxen_nic_driver_name);
+
+ }
+ return addr;
+}
+
+/* read num_words from hardware (num_words in 64 bits */
+void
+netxen_nic_mem_block_read(struct netxen_adapter *adapter, u64 off,
+ void *data, int num_words)
+{
+ void *addr;
+ unsigned long flags;
+
+ write_lock_irqsave(&adapter->adapter_lock, flags);
+ off = netxen_nic_pci_set_window(adapter->ahw.pci_base, off);
+ addr = (void *)(ptrdiff_t) (adapter->ahw.pci_base + off);
+ DPRINTK(INFO, "reading from base %lx offset %lx addr %p\n",
+ adapter->ahw.pci_base, (unsigned long)off, addr);
+ NETXEN_NIC_HW_BLOCK_READ_64(data, addr, num_words);
+ write_unlock_irqrestore(&adapter->adapter_lock, flags);
+}
+
+int
+netxen_nic_pci_mem_write(struct netxen_adapter *adapter, u64 off,
+ void *data, int size)
+{
+ unsigned long flags;
+ void *addr;
+ int ret = 0;
+
+ write_lock_irqsave(&adapter->adapter_lock, flags);
+ off = netxen_nic_pci_set_window(adapter->ahw.pci_base, off);
+ addr = (void *)(ptrdiff_t) (adapter->ahw.pci_base + off);
+ DPRINTK(INFO, "writing data %llx to offset %llx\n",
+ *(unsigned long long *)data, off);
+ switch (size) {
+ case 1:
+ writeb(*(u8 *) data, addr);
+ break;
+ case 2:
+ writew(*(u16 *) data, addr);
+ break;
+ case 4:
+ writel(*(u32 *) data, addr);
+ break;
+ case 8:
+ writeq(*(u64 *) data, addr);
+ break;
+ default:
+ ret = 1;
+ break;
+ }
+ write_unlock_irqrestore(&adapter->adapter_lock, flags);
+ DPRINTK(INFO, "wrote %llx\n", *(unsigned long long *)data);
+
+ return ret;
+}
+
+int
+netxen_nic_pci_mem_read(struct netxen_adapter *adapter,
+ u64 off, void *data, int size)
+{
+ unsigned long flags;
+ void *addr;
+ int ret = 0;
+
+ if (data == NULL || off > NETXEN_MEMADDR_MAX) {
+ printk(KERN_ERR "data: %p off:%llx\n", data, off);
+ return 1;
+ }
+ write_lock_irqsave(&adapter->adapter_lock, flags);
+ off = netxen_nic_pci_set_window(adapter->ahw.pci_base, off);
+ addr = (void *)(ptrdiff_t) (adapter->ahw.pci_base + off);
+ switch (size) {
+ case 1:
+ *(u8 *) data = readb(addr);
+ break;
+ case 2:
+ *(u16 *) data = readw(addr);
+ break;
+ case 4:
+ *(u32 *) data = readl(addr);
+ break;
+ case 8:
+ *(u64 *) data = readq(addr);
+ break;
+ default:
+ ret = 1;
+ break;
+ }
+ write_unlock_irqrestore(&adapter->adapter_lock, flags);
+ DPRINTK(INFO, "read %llx\n", *(unsigned long long *)data);
+
+ return ret;
+}
Delete the above routines and just open-code the register accesses.
+int netxen_nic_get_board_info(struct netxen_adapter *adapter)
+{
+ int rv = 0;
+ int addr = BRDCFG_START;
+ struct netxen_board_info *boardinfo;
+ int index;
+ u32 *ptr32;
+
+ boardinfo = &adapter->ahw.boardcfg;
+ ptr32 = (u32 *) boardinfo;
+
+ for (index = 0; index < sizeof(struct netxen_board_info) /
sizeof(u32);
+ index++) {
+ if (netxen_rom_fast_read(adapter, addr, ptr32) == -1) {
+ rv = -1;
+ return rv;
+ }
+ ptr32++;
+ addr += sizeof(u32);
+ }
+ if (boardinfo->magic != NETXEN_BDINFO_MAGIC) {
+ printk("%s: ERROR reading %s board config."
+ " Read %x, expected %x\n", netxen_nic_driver_name,
+ netxen_nic_driver_name,
+ boardinfo->magic, NETXEN_BDINFO_MAGIC);
+ rv = -1;
+ }
+ if (boardinfo->header_version != NETXEN_BDINFO_VERSION) {
+ printk("%s: Unknown board config version."
+ " Read %x, expected %x\n", netxen_nic_driver_name,
+ boardinfo->header_version, NETXEN_BDINFO_VERSION);
+ rv = -1;
+ }
+
+ DPRINTK(INFO, "Discovered board type:0x%x ", boardinfo->board_type);
+ switch ((netxen_brdtype_t) boardinfo->board_type) {
+ case NETXEN_BRDTYPE_P2_SB35_4G:
+ adapter->ahw.board_type = NETXEN_NIC_GBE;
+ break;
+ case NETXEN_BRDTYPE_P2_SB31_10G:
+ case NETXEN_BRDTYPE_P2_SB31_10G_IMEZ:
+ case NETXEN_BRDTYPE_P2_SB31_10G_HMEZ:
+ case NETXEN_BRDTYPE_P2_SB31_10G_CX4:
+ adapter->ahw.board_type = NETXEN_NIC_XGBE;
+ break;
+ case NETXEN_BRDTYPE_P1_BD:
+ case NETXEN_BRDTYPE_P1_SB:
+ case NETXEN_BRDTYPE_P1_SMAX:
+ case NETXEN_BRDTYPE_P1_SOCK:
+ adapter->ahw.board_type = NETXEN_NIC_GBE;
+ break;
+ default:
+ printk("%s: Unknown(%x)\n", netxen_nic_driver_name,
+ boardinfo->board_type);
+ break;
+ }
+
+ return rv;
+}
+
+inline int netxen_nic_get_board_num(struct netxen_adapter *adapter)
+{
+ return adapter->ahw.boardcfg.board_num;
+}
+
+/* NIU access sections */
+
+/* Set the MAC address for a port */
+int netxen_nic_macaddr_set(struct netxen_port *port, u8 * addr)
+{
+ struct netxen_adapter *adapter = port->adapter;
+ int phy = port->portnum, ret = 0;
+
+ if ((phy < 0) || (phy > 3))
+ return -1;
+
+ switch (adapter->ahw.board_type) {
+ case NETXEN_NIC_GBE:
+ ret = netxen_niu_macaddr_set(adapter, phy, addr);
+ break;
+
+ case NETXEN_NIC_XGBE:
+ ret = netxen_niu_xg_macaddr_set(adapter, phy, addr);
+ break;
+
+ default:
+ dump_stack();
+ printk(KERN_ERR "%s: Unknown board type\n",
+ netxen_nic_driver_name);
+ ret = -1;
+ }
+
+ return ret;
+}
+
+/* Return the current MAC address of the given port. */
+int netxen_nic_macaddr_get(struct netxen_port *port, u8 ** addr)
+{
+ struct netxen_adapter *adapter = port->adapter;
+ int phy = port->portnum;
+ int ret = 0;
+
+ if (addr == NULL)
+ return -1;
+ if ((phy < 0) || (phy > 3))
+ return -1;
+
+ switch (adapter->ahw.board_type) {
+ case NETXEN_NIC_GBE:
+ ret = netxen_niu_macaddr_get(adapter, phy,
+ (netxen_ethernet_macaddr_t *) *
+ addr);
+ break;
+
+ case NETXEN_NIC_XGBE:
+ printk(KERN_ERR "%s: Function %s is not implemented for XG\n",
+ netxen_nic_driver_name, __FUNCTION__);
+ break;
+
+ default:
+ printk(KERN_ERR "%s: Unknown board type\n",
+ netxen_nic_driver_name);
+ ret = -1;
+ }
+
+ return ret;
+}
+
+int netxen_nic_set_mtu(struct netxen_port *port, int new_mtu)
+{
+ struct netxen_adapter *adapter = port->adapter;
+ int ret = 0;
+
+ switch (adapter->ahw.board_type) {
+ case NETXEN_NIC_GBE:
+ netxen_nic_write_w0(adapter,
+ NETXEN_NIU_GB_MAX_FRAME_SIZE(port->portnum),
+ new_mtu);
+
+ break;
+
+ case NETXEN_NIC_XGBE:
+ new_mtu += 100; /* so that MAC accepts frames > MTU */
+ netxen_nic_write_w0(adapter, NETXEN_NIU_XGE_MAX_FRAME_SIZE,
+ new_mtu);
+ break;
+
+ default:
+ printk(KERN_ERR "%s: Unknown board type\n",
+ netxen_nic_driver_name);
+ ret = -1;
+ }
+
+ return ret;
+}
+
+int netxen_nic_set_promisc_mode(struct netxen_port *port)
+{
+ struct netxen_adapter *adapter = port->adapter;
+ int phy = port->portnum;
+ int ret = 0;
+
+ if ((phy < 0) || (phy > 3))
+ return -1;
+
+ switch (adapter->ahw.board_type) {
+ case NETXEN_NIC_GBE:
+ ret = netxen_niu_set_promiscuous_mode(adapter, phy,
+ NETXEN_NIU_PROMISCOUS_MODE);
+ break;
+
+ case NETXEN_NIC_XGBE:
+ ret = netxen_niu_xg_set_promiscuous_mode(adapter, phy,
+ NETXEN_NIU_PROMISCOUS_MODE);
+
+ break;
+
+ default:
+ printk(KERN_ERR "%s: Unknown board type\n",
+ netxen_nic_driver_name);
+ ret = -1;
+ }
+
+ return ret;
+}
+
+int netxen_nic_unset_promisc_mode(struct netxen_port *port)
+{
+ struct netxen_adapter *adapter = port->adapter;
+ int phy = port->portnum;
+ int ret = 0;
+
+ if ((phy < 0) || (phy > 3))
+ return -1;
+
+ switch (adapter->ahw.board_type) {
+ case NETXEN_NIC_GBE:
+ ret = netxen_niu_set_promiscuous_mode(adapter, phy,
+ NETXEN_NIU_NON_PROMISCOUS_MODE);
+ break;
+
+ case NETXEN_NIC_XGBE:
+ ret = netxen_niu_xg_set_promiscuous_mode(adapter, phy,
+ NETXEN_NIU_NON_PROMISCOUS_MODE);
+
+ break;
+
+ default:
+ printk(KERN_ERR "%s: Unknown board type\n",
+ netxen_nic_driver_name);
+ ret = -1;
+ }
1) two functions for such a simple task is overkill
2) just create separate hooks for GBE and XGBE, and eliminate these
wrapper functions that do nothing but "switch (adapter->ahw.board_type)"
before calling board-specific functions.
+long
+netxen_nic_phy_read(struct netxen_adapter *adapter, long phy, long reg,
+ u32 * readval)
+{
+ long ret = 0;
+
+ switch (adapter->ahw.board_type) {
+ case NETXEN_NIC_GBE:
+ ret = netxen_niu_gbe_phy_read(adapter, phy, reg, readval);
+ break;
+
+ case NETXEN_NIC_XGBE:
+ printk(KERN_ERR "%s: Function %s is not implemented for XG\n",
+ netxen_nic_driver_name, __FUNCTION__);
+ break;
+
+ default:
+ printk(KERN_ERR "%s: Unknown board type\n",
+ netxen_nic_driver_name);
+ ret = -1;
+ }
+
+ return ret;
+}
+
+long netxen_nic_phy_write(struct netxen_adapter *adapter, long phy,
long reg,
+ u32 val)
+{
+ long ret = 0;
+
+ switch (adapter->ahw.board_type) {
+ case NETXEN_NIC_GBE:
+ ret = netxen_niu_gbe_phy_write(adapter, phy, reg, val);
+ break;
+
+ case NETXEN_NIC_XGBE:
+ printk(KERN_ERR "%s: Function %s is not implemented for XG\n",
+ netxen_nic_driver_name, __FUNCTION__);
+ break;
+
+ default:
+ printk(KERN_ERR "%s: Unknown board type\n",
+ netxen_nic_driver_name);
+ ret = -1;
+ }
+
+ return ret;
+}
+
+long netxen_nic_init_port(struct netxen_port *port)
+{
+ struct netxen_adapter *adapter = port->adapter;
+ long portnum = port->portnum;
+ long ret = 0;
+
+ switch (adapter->ahw.board_type) {
+ case NETXEN_NIC_GBE:
+ netxen_nic_disable_phy_interrupts(adapter, portnum);
+ udelay(20000);
NAK!! It is unacceptable to spin the CPU for so long.
+ netxen_niu_gbe_init_port(adapter, portnum);
+
+ break;
+
+ case NETXEN_NIC_XGBE:
+ /* Nothing to be done for XG */
+ break;
+
+ default:
+ printk(KERN_ERR "%s: Unknown board type\n",
+ netxen_nic_driver_name);
+ ret = -1;
+ }
+
+ return ret;
+}
+
+void netxen_nic_init_niu(struct netxen_adapter *adapter)
+{
+ int portno;
+
+ switch (adapter->ahw.board_type) {
+ case NETXEN_NIC_GBE:
+ for (portno = 0; portno < NETXEN_NIU_MAX_GBE_PORTS; portno++)
+ netxen_niu_gbe_init_port(adapter, portno);
+ break;
+
+ case NETXEN_NIC_XGBE:
+ /* Do nothing */
+ break;
+
+ default:
+ printk(KERN_ERR "%s: Unknown board type\n",
+ netxen_nic_driver_name);
+ }
+}
+
+void netxen_nic_stop_port(struct netxen_port *port)
+{
+ long portnum = port->portnum;
+ struct netxen_adapter *adapter = port->adapter;
+
+ switch (adapter->ahw.board_type) {
+ case NETXEN_NIC_GBE:
+ netxen_niu_disable_gbe_port(adapter, portnum);
+ break;
+
+ case NETXEN_NIC_XGBE:
+ netxen_niu_disable_xg_port(adapter, portnum);
+ break;
+
+ default:
+ printk(KERN_ERR "%s: Unknown board type\n",
+ netxen_nic_driver_name);
+ }
+}
+
+void netxen_nic_stop_all_ports(struct netxen_adapter *adapter)
+{
+ int port_nr;
+ struct netxen_port *port;
+
+ for (port_nr = 0; port_nr < adapter->ahw.max_ports; port_nr++) {
+ port = adapter->port[port_nr];
+ netxen_nic_stop_port(port);
+ }
+}
+
+void
+netxen_crb_writelit_adapter(struct netxen_adapter *adapter, unsigned
long off,
+ int data)
+{
+ unsigned long flags;
+ void *addr;
+
+ if (ADDR_IN_WINDOW1(off)) {
+ read_lock(&adapter->adapter_lock);
+ writel(data, NETXEN_CRB_NORMALIZE(adapter, off));
+ read_unlock(&adapter->adapter_lock);
+ } else {
+ write_lock_irqsave(&adapter->adapter_lock, flags);
+ netxen_nic_pci_change_crbwindow(adapter, 0);
+ addr = (void *)(adapter->ahw.pci_base + off);
+ writel(data, addr);
+ netxen_nic_pci_change_crbwindow(adapter, 1);
+ write_unlock_irqrestore(&adapter->adapter_lock, flags);
+ }
+}
+
+void netxen_nic_set_link_parameters(struct netxen_port *port)
+{
+ struct netxen_adapter *adapter = port->adapter;
+ struct netxen_niu_phy_status status;
+ u16 autoneg;
+ struct netxen_niu_control mode;
+
+ netxen_nic_read_w0(adapter, NETXEN_NIU_MODE, (u32 *) & mode);
+ if (mode.enable_ge) { /* Gb 10/100/1000 Mbps mode */
+ if (netxen_nic_phy_read(port->adapter, port->portnum,
+ NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_STATUS,
+ (netxen_crbword_t *) & status) == 0) {
+ if (status.link) {
+ switch (status.speed) {
+ case 0:
+ port->link_speed = SPEED_10;
+ break;
+ case 1:
+ port->link_speed = SPEED_100;
+ break;
+ case 2:
+ port->link_speed = SPEED_1000;
+ break;
+ default:
+ port->link_speed = -1; /* unknown speed */
+ break;
+ }
+ switch (status.duplex) {
+ case 0:
+ port->link_duplex = DUPLEX_HALF;
+ break;
+ case 1:
+ port->link_duplex = DUPLEX_FULL;
+ break;
+ default:
+ port->link_duplex = -1; /* unknown mode */
+ break;
+ }
+ if (netxen_nic_phy_read(port->adapter,
+ port->portnum,
+ NETXEN_NIU_GB_MII_MGMT_ADDR_AUTONEG,
+ (netxen_crbword_t *) &
+ autoneg) != 0)
+ port->link_autoneg = autoneg;
+ } else
+ goto link_down;
+ } else {
+ link_down:
+ port->link_speed = -1;
+ port->link_duplex = -1;
+ }
+ }
+}
+
+void netxen_nic_flash_print(struct netxen_adapter *adapter)
+{
+ int valid = 1;
+ u32 fw_major = 0;
+ u32 fw_minor = 0;
+ u32 fw_build = 0;
+
+ struct netxen_board_info *board_info = &(adapter->ahw.boardcfg);
+ if (board_info->magic != NETXEN_BDINFO_MAGIC) {
+ printk
+ ("NetXen Unknown board config, Read 0x%x expected as 0x%x\n",
+ board_info->magic, NETXEN_BDINFO_MAGIC);
+ valid = 0;
+ }
+ if (board_info->header_version != NETXEN_BDINFO_VERSION) {
+ printk("NetXen Unknown board config version."
+ " Read %x, expected %x\n",
+ board_info->header_version, NETXEN_BDINFO_VERSION);
+ valid = 0;
+ }
+ if (valid) {
+ printk("NetXen %s Board #%d, Chip id 0x%x\n",
+ board_info->board_type == 0x0b ? "XGB" : "GBE",
+ board_info->board_num, board_info->chip_id);
+ read_lock(&adapter->adapter_lock);
+ fw_major = readl(NETXEN_CRB_NORMALIZE(adapter,
+ NETXEN_FW_VERSION_MAJOR));
+ fw_minor = readl(NETXEN_CRB_NORMALIZE(adapter,
+ NETXEN_FW_VERSION_MINOR));
+ fw_build =
+ readl(NETXEN_CRB_NORMALIZE(adapter, NETXEN_FW_VERSION_SUB));
+ read_unlock(&adapter->adapter_lock);
+
+ printk("NetXen Firmware version %d.%d.%d\n", fw_major, fw_minor,
+ fw_build);
+ }
+ if (fw_major != _NETXEN_NIC_LINUX_MAJOR) {
+ printk(KERN_ERR "The mismatch in driver version and firmware "
+ "version major number\n"
+ "Driver version major number = %d \t"
+ "Firmware version major number = %d \n",
+ _NETXEN_NIC_LINUX_MAJOR, fw_major);
+ adapter->driver_mismatch = 1;
+ }
+ if (fw_minor != _NETXEN_NIC_LINUX_MINOR) {
+ printk(KERN_ERR "The mismatch in driver version and firmware "
+ "version minor number\n"
+ "Driver version minor number = %d \t"
+ "Firmware version minor number = %d \n",
+ _NETXEN_NIC_LINUX_MINOR, fw_minor);
+ adapter->driver_mismatch = 1;
+ }
+ if (adapter->driver_mismatch)
+ printk(KERN_INFO "Use the driver with version no %d.%d.xxx\n",
+ fw_major, fw_minor);
+}
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
