I've been digging around trying to get some information on the current status
of interrupt mitigation features for a Braodcom 5704 interface.
Specifically I'm sending and receiving lots of VoIP packets (50 pps per stream,
many streams).
What I can't seem to determine is this:
What version of the linux kernel & tg3 drivers are required to support both rx
and tx mitigation?
What do the ethtool coalescence settings actually do (I've not been able to
find actual descriptions of the different parameters in the -C section)
Is there anything special that needs to be done when compiling a kernel to
enable this feature for both the kernel and the tg3 driver.
Just a warning, I'm not a C coder, so I've not had much luck digging around the
code and looking for answers.
I've currently got a blade server with 10 blades I'm using 9 blades to generate
this small packet high rate traffic to the 10th blade and trying to improve the
ability of a blade to handle VoIP traffic. I made some guesses at settings for
the -C options in ethtool on both the test blade and the traffic generators.
Interestingly it seems to have had a very good effect on the test blade (%cpu
for interrupt down from 99.9% to ~20%), but the same settings on the traffic
generation servers seems to have had no effect.
Hardware is identical, kernel is identical.
Any help is GREATLY appreciated.
-Chris
05:01.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704S
Gigabit Ethernet (rev 10)
Subsystem: IBM: Unknown device 02e8
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 201
Memory at dcfe0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+
Queue=0/3 Enable-
Linux version 2.6.9-34.ELsmp ([EMAIL PROTECTED]) (gcc version
3.4.5 20051201 (Red Hat 3.4.5-2)) #1 SMP Thu Mar 9 06:23:23 GMT 2006
[EMAIL PROTECTED] ~]# ethtool -c eth1
Coalesce parameters for eth1:
Adaptive RX: off TX: off
stats-block-usecs: 1000000
sample-interval: 0
pkt-rate-low: 0
pkt-rate-high: 0
rx-usecs: 500
rx-frames: 30
rx-usecs-irq: 500
rx-frames-irq: 20
tx-usecs: 400
tx-frames: 53
tx-usecs-irq: 490
tx-frames-irq: 5
rx-usecs-low: 0
rx-frame-low: 0
tx-usecs-low: 0
tx-frame-low: 0
rx-usecs-high: 0
rx-frame-high: 0
tx-usecs-high: 0
tx-frame-high: 0
[EMAIL PROTECTED] ~]# ethtool -i eth1
driver: tg3
version: 3.43-rh
firmware-version:
bus-info: 0000:05:01.1
[EMAIL PROTECTED] ~]# ethtool eth1
Settings for eth1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Half 1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
Link detected: yes
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
