commit 25a0324ef1c1b181c9d00f09837e8757875ee2a4
Author: Jeff Garzik <[EMAIL PROTECTED]>
Date: Tue Jun 27 10:47:51 2006 -0400
[netdrvr] Use dev_printk() when ethernet interface isn't available
For messages prior to register_netdev(), prefer dev_printk() because
that prints out both our driver name and our [PCI | whatever] bus id.
Updates: 8139{cp,too}, b44, bnx2, cassini, {eepro,epic}100, fealnx,
hamachi, ne2k-pci, ns83820, pci-skeleton, r8169.
Signed-off-by: Jeff Garzik <[EMAIL PROTECTED]>
drivers/net/8139cp.c | 36 +++++++++++++++++++++---------------
drivers/net/8139too.c | 41 +++++++++++++++++++++++++----------------
drivers/net/b44.c | 28 +++++++++++++++-------------
drivers/net/bnx2.c | 37 ++++++++++++++++++++++---------------
drivers/net/cassini.c | 20 ++++++++++----------
drivers/net/eepro100.c | 8 +++++---
drivers/net/epic100.c | 23 ++++++++++++-----------
drivers/net/fealnx.c | 17 +++++++++--------
drivers/net/hamachi.c | 3 ++-
drivers/net/ne2k-pci.c | 12 ++++++++----
drivers/net/ns83820.c | 14 +++++++++-----
drivers/net/pci-skeleton.c | 24 +++++++++++++++---------
drivers/net/r8169.c | 43 +++++++++++++++++++------------------------
13 files changed, 172 insertions(+), 134 deletions(-)
25a0324ef1c1b181c9d00f09837e8757875ee2a4
diff --git a/drivers/net/8139cp.c b/drivers/net/8139cp.c
index 0cdc830..c38e352 100644
--- a/drivers/net/8139cp.c
+++ b/drivers/net/8139cp.c
@@ -1837,9 +1837,11 @@ #endif
if (pdev->vendor == PCI_VENDOR_ID_REALTEK &&
pdev->device == PCI_DEVICE_ID_REALTEK_8139 && pci_rev < 0x20) {
- printk(KERN_ERR PFX "pci dev %s (id %04x:%04x rev %02x) is not
an 8139C+ compatible chip\n",
- pci_name(pdev), pdev->vendor, pdev->device, pci_rev);
- printk(KERN_ERR PFX "Try the \"8139too\" driver instead.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "This (id %04x:%04x rev %02x) is not an 8139C+
compatible chip\n",
+ pdev->vendor, pdev->device, pci_rev);
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Try the \"8139too\" driver instead.\n");
return -ENODEV;
}
@@ -1877,14 +1879,14 @@ #endif
pciaddr = pci_resource_start(pdev, 1);
if (!pciaddr) {
rc = -EIO;
- printk(KERN_ERR PFX "no MMIO resource for pci dev %s\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev, "no MMIO resource\n");
goto err_out_res;
}
if (pci_resource_len(pdev, 1) < CP_REGS_SIZE) {
rc = -EIO;
- printk(KERN_ERR PFX "MMIO resource (%lx) too small on pci dev
%s\n",
- pci_resource_len(pdev, 1), pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "MMIO resource (%lx) too small\n",
+ pci_resource_len(pdev, 1));
goto err_out_res;
}
@@ -1898,14 +1900,15 @@ #endif
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR PFX "No usable DMA configuration, "
- "aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "No usable DMA configuration, aborting.\n");
goto err_out_res;
}
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR PFX "No usable consistent DMA
configuration, "
- "aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "No usable consistent DMA configuration, "
+ "aborting.\n");
goto err_out_res;
}
}
@@ -1916,8 +1919,9 @@ #endif
regs = ioremap(pciaddr, CP_REGS_SIZE);
if (!regs) {
rc = -EIO;
- printk(KERN_ERR PFX "Cannot map PCI MMIO ([EMAIL PROTECTED]) on
pci dev %s\n",
- pci_resource_len(pdev, 1), pciaddr, pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Cannot map PCI MMIO ([EMAIL PROTECTED])\n",
+ pci_resource_len(pdev, 1), pciaddr);
goto err_out_res;
}
dev->base_addr = (unsigned long) regs;
@@ -1986,7 +1990,8 @@ #endif
/* enable busmastering and memory-write-invalidate */
pci_set_master(pdev);
- if (cp->wol_enabled) cp_set_d3_state (cp);
+ if (cp->wol_enabled)
+ cp_set_d3_state (cp);
return 0;
@@ -2011,7 +2016,8 @@ static void cp_remove_one (struct pci_de
BUG_ON(!dev);
unregister_netdev(dev);
iounmap(cp->regs);
- if (cp->wol_enabled) pci_set_power_state (pdev, PCI_D0);
+ if (cp->wol_enabled)
+ pci_set_power_state (pdev, PCI_D0);
pci_release_regions(pdev);
pci_clear_mwi(pdev);
pci_disable_device(pdev);
diff --git a/drivers/net/8139too.c b/drivers/net/8139too.c
index abd6261..b2592c4 100644
--- a/drivers/net/8139too.c
+++ b/drivers/net/8139too.c
@@ -769,7 +769,8 @@ static int __devinit rtl8139_init_board
/* dev and priv zeroed in alloc_etherdev */
dev = alloc_etherdev (sizeof (*tp));
if (dev == NULL) {
- printk (KERN_ERR PFX "%s: Unable to alloc new net device\n",
pci_name(pdev));
+ dev_printk (KERN_ERR, &pdev->dev,
+ "Unable to alloc new net device\n");
return -ENOMEM;
}
SET_MODULE_OWNER(dev);
@@ -801,31 +802,35 @@ static int __devinit rtl8139_init_board
#ifdef USE_IO_OPS
/* make sure PCI base addr 0 is PIO */
if (!(pio_flags & IORESOURCE_IO)) {
- printk (KERN_ERR PFX "%s: region #0 not a PIO resource,
aborting\n", pci_name(pdev));
+ dev_printk (KERN_ERR, &pdev->dev,
+ "region #0 not a PIO resource, aborting\n");
rc = -ENODEV;
goto err_out;
}
/* check for weird/broken PCI region reporting */
if (pio_len < RTL_MIN_IO_SIZE) {
- printk (KERN_ERR PFX "%s: Invalid PCI I/O region size(s),
aborting\n", pci_name(pdev));
+ dev_printk (KERN_ERR, &pdev->dev,
+ "Invalid PCI I/O region size(s), aborting\n");
rc = -ENODEV;
goto err_out;
}
#else
/* make sure PCI base addr 1 is MMIO */
if (!(mmio_flags & IORESOURCE_MEM)) {
- printk (KERN_ERR PFX "%s: region #1 not an MMIO resource,
aborting\n", pci_name(pdev));
+ dev_printk (KERN_ERR, &pdev->dev,
+ "region #1 not an MMIO resource, aborting\n");
rc = -ENODEV;
goto err_out;
}
if (mmio_len < RTL_MIN_IO_SIZE) {
- printk (KERN_ERR PFX "%s: Invalid PCI mem region size(s),
aborting\n", pci_name(pdev));
+ dev_printk (KERN_ERR, &pdev->dev,
+ "Invalid PCI mem region size(s), aborting\n");
rc = -ENODEV;
goto err_out;
}
#endif
- rc = pci_request_regions (pdev, "8139too");
+ rc = pci_request_regions (pdev, DRV_NAME);
if (rc)
goto err_out;
disable_dev_on_err = 1;
@@ -836,7 +841,7 @@ #endif
#ifdef USE_IO_OPS
ioaddr = ioport_map(pio_start, pio_len);
if (!ioaddr) {
- printk (KERN_ERR PFX "%s: cannot map PIO, aborting\n",
pci_name(pdev));
+ dev_printk (KERN_ERR, &pdev->dev, "cannot map PIO, aborting\n");
rc = -EIO;
goto err_out;
}
@@ -847,7 +852,8 @@ #else
/* ioremap MMIO region */
ioaddr = pci_iomap(pdev, 1, 0);
if (ioaddr == NULL) {
- printk (KERN_ERR PFX "%s: cannot remap MMIO, aborting\n",
pci_name(pdev));
+ dev_printk (KERN_ERR, &pdev->dev,
+ "cannot remap MMIO, aborting\n");
rc = -EIO;
goto err_out;
}
@@ -861,8 +867,8 @@ #endif /* USE_IO_OPS */
/* check for missing/broken hardware */
if (RTL_R32 (TxConfig) == 0xFFFFFFFF) {
- printk (KERN_ERR PFX "%s: Chip not responding, ignoring
board\n",
- pci_name(pdev));
+ dev_printk (KERN_ERR, &pdev->dev,
+ "Chip not responding, ignoring board\n");
rc = -EIO;
goto err_out;
}
@@ -876,9 +882,10 @@ #endif /* USE_IO_OPS */
}
/* if unknown chip, assume array element #0, original RTL-8139 in this
case */
- printk (KERN_DEBUG PFX "%s: unknown chip version, assuming RTL-8139\n",
- pci_name(pdev));
- printk (KERN_DEBUG PFX "%s: TxConfig = 0x%lx\n", pci_name(pdev),
RTL_R32 (TxConfig));
+ dev_printk (KERN_DEBUG, &pdev->dev,
+ "unknown chip version, assuming RTL-8139\n");
+ dev_printk (KERN_DEBUG, &pdev->dev,
+ "TxConfig = 0x%lx\n", RTL_R32 (TxConfig));
tp->chipset = 0;
match:
@@ -955,9 +962,11 @@ #endif
if (pdev->vendor == PCI_VENDOR_ID_REALTEK &&
pdev->device == PCI_DEVICE_ID_REALTEK_8139 && pci_rev >= 0x20) {
- printk(KERN_INFO PFX "pci dev %s (id %04x:%04x rev %02x) is an
enhanced 8139C+ chip\n",
- pci_name(pdev), pdev->vendor, pdev->device, pci_rev);
- printk(KERN_INFO PFX "Use the \"8139cp\" driver for improved
performance and stability.\n");
+ dev_printk(KERN_INFO, &pdev->dev,
+ "This (id %04x:%04x rev %02x) is an enhanced 8139C+
chip\n",
+ pdev->vendor, pdev->device, pci_rev);
+ dev_printk(KERN_INFO, &pdev->dev,
+ "Use the \"8139cp\" driver for improved performance
and stability.\n");
}
i = rtl8139_init_board (pdev, &dev);
diff --git a/drivers/net/b44.c b/drivers/net/b44.c
index a7e4ba5..6d7748d 100644
--- a/drivers/net/b44.c
+++ b/drivers/net/b44.c
@@ -2120,13 +2120,14 @@ static int __devinit b44_init_one(struct
err = pci_enable_device(pdev);
if (err) {
- printk(KERN_ERR PFX "Cannot enable PCI device, "
+ dev_printk(KERN_ERR, &pdev->dev, "Cannot enable PCI device, "
"aborting.\n");
return err;
}
if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) {
- printk(KERN_ERR PFX "Cannot find proper PCI device "
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Cannot find proper PCI device "
"base address, aborting.\n");
err = -ENODEV;
goto err_out_disable_pdev;
@@ -2134,8 +2135,8 @@ static int __devinit b44_init_one(struct
err = pci_request_regions(pdev, DRV_MODULE_NAME);
if (err) {
- printk(KERN_ERR PFX "Cannot obtain PCI resources, "
- "aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Cannot obtain PCI resources, aborting.\n");
goto err_out_disable_pdev;
}
@@ -2143,15 +2144,15 @@ static int __devinit b44_init_one(struct
err = pci_set_dma_mask(pdev, (u64) B44_DMA_MASK);
if (err) {
- printk(KERN_ERR PFX "No usable DMA configuration, "
- "aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "No usable DMA configuration, aborting.\n");
goto err_out_free_res;
}
err = pci_set_consistent_dma_mask(pdev, (u64) B44_DMA_MASK);
if (err) {
- printk(KERN_ERR PFX "No usable DMA configuration, "
- "aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "No usable DMA configuration, aborting.\n");
goto err_out_free_res;
}
@@ -2160,7 +2161,8 @@ static int __devinit b44_init_one(struct
dev = alloc_etherdev(sizeof(*bp));
if (!dev) {
- printk(KERN_ERR PFX "Etherdev alloc failed, aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Etherdev alloc failed, aborting.\n");
err = -ENOMEM;
goto err_out_free_res;
}
@@ -2181,7 +2183,7 @@ static int __devinit b44_init_one(struct
bp->regs = ioremap(b44reg_base, b44reg_len);
if (bp->regs == 0UL) {
- printk(KERN_ERR PFX "Cannot map device registers, "
+ dev_printk(KERN_ERR, &pdev->dev, "Cannot map device registers, "
"aborting.\n");
err = -ENOMEM;
goto err_out_free_dev;
@@ -2212,8 +2214,8 @@ #endif
err = b44_get_invariants(bp);
if (err) {
- printk(KERN_ERR PFX "Problem fetching invariants of chip, "
- "aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Problem fetching invariants of chip, aborting.\n");
goto err_out_iounmap;
}
@@ -2233,7 +2235,7 @@ #endif
err = register_netdev(dev);
if (err) {
- printk(KERN_ERR PFX "Cannot register net device, "
+ dev_printk(KERN_ERR, &pdev->dev, "Cannot register net device, "
"aborting.\n");
goto err_out_iounmap;
}
diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c
index 7635736..171e498 100644
--- a/drivers/net/bnx2.c
+++ b/drivers/net/bnx2.c
@@ -5566,20 +5566,22 @@ bnx2_init_board(struct pci_dev *pdev, st
/* enable device (incl. PCI PM wakeup), and bus-mastering */
rc = pci_enable_device(pdev);
if (rc) {
- printk(KERN_ERR PFX "Cannot enable PCI device, aborting.");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Cannot enable PCI device, aborting.");
goto err_out;
}
if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) {
- printk(KERN_ERR PFX "Cannot find PCI device base address, "
- "aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Cannot find PCI device base address, aborting.\n");
rc = -ENODEV;
goto err_out_disable;
}
rc = pci_request_regions(pdev, DRV_MODULE_NAME);
if (rc) {
- printk(KERN_ERR PFX "Cannot obtain PCI resources, aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Cannot obtain PCI resources, aborting.\n");
goto err_out_disable;
}
@@ -5587,15 +5589,16 @@ bnx2_init_board(struct pci_dev *pdev, st
bp->pm_cap = pci_find_capability(pdev, PCI_CAP_ID_PM);
if (bp->pm_cap == 0) {
- printk(KERN_ERR PFX "Cannot find power management capability, "
- "aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Cannot find power management capability, aborting.\n");
rc = -EIO;
goto err_out_release;
}
bp->pcix_cap = pci_find_capability(pdev, PCI_CAP_ID_PCIX);
if (bp->pcix_cap == 0) {
- printk(KERN_ERR PFX "Cannot find PCIX capability, aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Cannot find PCIX capability, aborting.\n");
rc = -EIO;
goto err_out_release;
}
@@ -5603,14 +5606,15 @@ bnx2_init_board(struct pci_dev *pdev, st
if (pci_set_dma_mask(pdev, DMA_64BIT_MASK) == 0) {
bp->flags |= USING_DAC_FLAG;
if (pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK) != 0) {
- printk(KERN_ERR PFX "pci_set_consistent_dma_mask "
- "failed, aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "pci_set_consistent_dma_mask failed,
aborting.\n");
rc = -EIO;
goto err_out_release;
}
}
else if (pci_set_dma_mask(pdev, DMA_32BIT_MASK) != 0) {
- printk(KERN_ERR PFX "System does not support DMA, aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "System does not support DMA, aborting.\n");
rc = -EIO;
goto err_out_release;
}
@@ -5630,7 +5634,8 @@ bnx2_init_board(struct pci_dev *pdev, st
bp->regview = ioremap_nocache(dev->base_addr, mem_len);
if (!bp->regview) {
- printk(KERN_ERR PFX "Cannot map register space, aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Cannot map register space, aborting.\n");
rc = -ENOMEM;
goto err_out_release;
}
@@ -5702,8 +5707,8 @@ bnx2_init_board(struct pci_dev *pdev, st
else if ((CHIP_ID(bp) == CHIP_ID_5706_A1) &&
!(bp->flags & PCIX_FLAG)) {
- printk(KERN_ERR PFX "5706 A1 can only be used in a PCIX bus, "
- "aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "5706 A1 can only be used in a PCIX bus, aborting.\n");
goto err_out_unmap;
}
@@ -5724,7 +5729,8 @@ bnx2_init_board(struct pci_dev *pdev, st
if ((reg & BNX2_DEV_INFO_SIGNATURE_MAGIC_MASK) !=
BNX2_DEV_INFO_SIGNATURE_MAGIC) {
- printk(KERN_ERR PFX "Firmware not running, aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Firmware not running, aborting.\n");
rc = -ENODEV;
goto err_out_unmap;
}
@@ -5886,7 +5892,8 @@ #if defined(HAVE_POLL_CONTROLLER) || def
#endif
if ((rc = register_netdev(dev))) {
- printk(KERN_ERR PFX "Cannot register net device\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Cannot register net device\n");
if (bp->regview)
iounmap(bp->regview);
pci_release_regions(pdev);
diff --git a/drivers/net/cassini.c b/drivers/net/cassini.c
index 565a54f..ccff239 100644
--- a/drivers/net/cassini.c
+++ b/drivers/net/cassini.c
@@ -4888,13 +4888,13 @@ static int __devinit cas_init_one(struct
err = pci_enable_device(pdev);
if (err) {
- printk(KERN_ERR PFX "Cannot enable PCI device, "
+ dev_printk(KERN_ERR, &pdev->dev, "Cannot enable PCI device, "
"aborting.\n");
return err;
}
if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) {
- printk(KERN_ERR PFX "Cannot find proper PCI device "
+ dev_printk(KERN_ERR, &pdev->dev, "Cannot find proper PCI device
"
"base address, aborting.\n");
err = -ENODEV;
goto err_out_disable_pdev;
@@ -4902,7 +4902,7 @@ static int __devinit cas_init_one(struct
dev = alloc_etherdev(sizeof(*cp));
if (!dev) {
- printk(KERN_ERR PFX "Etherdev alloc failed, aborting.\n");
+ dev_printk(KERN_ERR, &pdev->dev, "Etherdev alloc failed,
aborting.\n");
err = -ENOMEM;
goto err_out_disable_pdev;
}
@@ -4911,7 +4911,7 @@ static int __devinit cas_init_one(struct
err = pci_request_regions(pdev, dev->name);
if (err) {
- printk(KERN_ERR PFX "Cannot obtain PCI resources, "
+ dev_printk(KERN_ERR, &pdev->dev, "Cannot obtain PCI resources, "
"aborting.\n");
goto err_out_free_netdev;
}
@@ -4942,7 +4942,7 @@ #if 1
if (pci_write_config_byte(pdev,
PCI_CACHE_LINE_SIZE,
cas_cacheline_size)) {
- printk(KERN_ERR PFX "Could not set PCI cache "
+ dev_printk(KERN_ERR, &pdev->dev, "Could not set PCI
cache "
"line size\n");
goto err_write_cacheline;
}
@@ -4956,7 +4956,7 @@ #endif
err = pci_set_consistent_dma_mask(pdev,
DMA_64BIT_MASK);
if (err < 0) {
- printk(KERN_ERR PFX "Unable to obtain 64-bit DMA "
+ dev_printk(KERN_ERR, &pdev->dev, "Unable to obtain
64-bit DMA "
"for consistent allocations\n");
goto err_out_free_res;
}
@@ -4964,7 +4964,7 @@ #endif
} else {
err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (err) {
- printk(KERN_ERR PFX "No usable DMA configuration, "
+ dev_printk(KERN_ERR, &pdev->dev, "No usable DMA
configuration, "
"aborting.\n");
goto err_out_free_res;
}
@@ -5024,7 +5024,7 @@ #endif
/* give us access to cassini registers */
cp->regs = pci_iomap(pdev, 0, casreg_len);
if (cp->regs == 0UL) {
- printk(KERN_ERR PFX "Cannot map device registers, "
+ dev_printk(KERN_ERR, &pdev->dev, "Cannot map device registers, "
"aborting.\n");
goto err_out_free_res;
}
@@ -5041,7 +5041,7 @@ #endif
pci_alloc_consistent(pdev, sizeof(struct cas_init_block),
&cp->block_dvma);
if (!cp->init_block) {
- printk(KERN_ERR PFX "Cannot allocate init block, "
+ dev_printk(KERN_ERR, &pdev->dev, "Cannot allocate init block, "
"aborting.\n");
goto err_out_iounmap;
}
@@ -5086,7 +5086,7 @@ #endif
dev->features |= NETIF_F_HIGHDMA;
if (register_netdev(dev)) {
- printk(KERN_ERR PFX "Cannot register net device, "
+ dev_printk(KERN_ERR, &pdev->dev, "Cannot register net device, "
"aborting.\n");
goto err_out_free_consistent;
}
diff --git a/drivers/net/eepro100.c b/drivers/net/eepro100.c
index ecf5ad8..0b65a31 100644
--- a/drivers/net/eepro100.c
+++ b/drivers/net/eepro100.c
@@ -556,12 +556,14 @@ #endif
if (!request_region(pci_resource_start(pdev, 1),
pci_resource_len(pdev, 1), "eepro100")) {
- printk (KERN_ERR "eepro100: cannot reserve I/O ports\n");
+ dev_printk (KERN_ERR, &pdev->dev,
+ "eepro100: cannot reserve I/O ports\n");
goto err_out_none;
}
if (!request_mem_region(pci_resource_start(pdev, 0),
pci_resource_len(pdev, 0), "eepro100")) {
- printk (KERN_ERR "eepro100: cannot reserve MMIO region\n");
+ dev_printk (KERN_ERR, &pdev->dev,
+ "eepro100: cannot reserve MMIO region\n");
goto err_out_free_pio_region;
}
@@ -574,7 +576,7 @@ #endif
ioaddr = pci_iomap(pdev, pci_bar, 0);
if (!ioaddr) {
- printk (KERN_ERR "eepro100: cannot remap IO\n");
+ dev_printk (KERN_ERR, &pdev->dev, "eepro100: cannot remap
IO\n");
goto err_out_free_mmio_region;
}
diff --git a/drivers/net/epic100.c b/drivers/net/epic100.c
index 8dacd0d..1ec06a5 100644
--- a/drivers/net/epic100.c
+++ b/drivers/net/epic100.c
@@ -423,8 +423,7 @@ #endif
((u16 *)dev->dev_addr)[i] = le16_to_cpu(inw(ioaddr + LAN0 +
i*4));
if (debug > 2) {
- printk(KERN_DEBUG DRV_NAME "(%s): EEPROM contents\n",
- pci_name(pdev));
+ dev_printk(KERN_DEBUG, &pdev->dev, "EEPROM contents:\n");
for (i = 0; i < 64; i++)
printk(" %4.4x%s", read_eeprom(ioaddr, i),
i % 16 == 15 ? "\n" : "");
@@ -446,21 +445,23 @@ #endif
int mii_status = mdio_read(dev, phy, MII_BMSR);
if (mii_status != 0xffff && mii_status != 0x0000) {
ep->phys[phy_idx++] = phy;
- printk(KERN_INFO DRV_NAME "(%s): MII
transceiver #%d control "
- "%4.4x status %4.4x.\n",
- pci_name(pdev), phy, mdio_read(dev,
phy, 0), mii_status);
+ dev_printk(KERN_INFO, &pdev->dev,
+ "MII transceiver #%d control "
+ "%4.4x status %4.4x.\n",
+ phy, mdio_read(dev, phy, 0),
mii_status);
}
}
ep->mii_phy_cnt = phy_idx;
if (phy_idx != 0) {
phy = ep->phys[0];
ep->mii.advertising = mdio_read(dev, phy,
MII_ADVERTISE);
- printk(KERN_INFO DRV_NAME "(%s): Autonegotiation
advertising %4.4x link "
+ dev_printk(KERN_INFO, &pdev->dev,
+ "Autonegotiation advertising %4.4x link "
"partner %4.4x.\n",
- pci_name(pdev), ep->mii.advertising,
mdio_read(dev, phy, 5));
+ ep->mii.advertising, mdio_read(dev, phy, 5));
} else if ( ! (ep->chip_flags & NO_MII)) {
- printk(KERN_WARNING DRV_NAME "(%s): ***WARNING***: No
MII transceiver found!\n",
- pci_name(pdev));
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "***WARNING***: No MII transceiver found!\n");
/* Use the known PHY address of the EPII. */
ep->phys[0] = 3;
}
@@ -475,8 +476,8 @@ #endif
/* The lower four bits are the media type. */
if (duplex) {
ep->mii.force_media = ep->mii.full_duplex = 1;
- printk(KERN_INFO DRV_NAME "(%s): Forced full duplex operation
requested.\n",
- pci_name(pdev));
+ dev_printk(KERN_INFO, &pdev->dev,
+ "Forced full duplex operation requested.\n");
}
dev->if_port = ep->default_port = option;
diff --git a/drivers/net/fealnx.c b/drivers/net/fealnx.c
index 958ea51..9369082 100644
--- a/drivers/net/fealnx.c
+++ b/drivers/net/fealnx.c
@@ -578,9 +578,9 @@ #endif
if (mii_status != 0xffff && mii_status != 0x0000) {
np->phys[phy_idx++] = phy;
- printk(KERN_INFO
- "%s: MII PHY found at address %d, status
"
- "0x%4.4x.\n", dev->name, phy,
mii_status);
+ dev_printk(KERN_INFO, &pdev->dev,
+ "MII PHY found at address %d, status "
+ "0x%4.4x.\n", phy, mii_status);
/* get phy type */
{
unsigned int data;
@@ -603,10 +603,10 @@ #endif
}
np->mii_cnt = phy_idx;
- if (phy_idx == 0) {
- printk(KERN_WARNING "%s: MII PHY not found -- this
device may "
- "not operate correctly.\n", dev->name);
- }
+ if (phy_idx == 0)
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "MII PHY not found -- this device may "
+ "not operate correctly.\n");
} else {
np->phys[0] = 32;
/* 89/6/23 add, (begin) */
@@ -632,7 +632,8 @@ #endif
np->mii.full_duplex = full_duplex[card_idx];
if (np->mii.full_duplex) {
- printk(KERN_INFO "%s: Media type forced to Full Duplex.\n",
dev->name);
+ dev_printk(KERN_INFO, &pdev->dev,
+ "Media type forced to Full Duplex.\n");
/* 89/6/13 add, (begin) */
// if (np->PHYType==MarvellPHY)
if ((np->PHYType == MarvellPHY) || (np->PHYType ==
LevelOnePHY)) {
diff --git a/drivers/net/hamachi.c b/drivers/net/hamachi.c
index 2b91099..168eb4e 100644
--- a/drivers/net/hamachi.c
+++ b/drivers/net/hamachi.c
@@ -601,7 +601,8 @@ #endif
pci_set_master(pdev);
i = pci_request_regions(pdev, DRV_NAME);
- if (i) return i;
+ if (i)
+ return i;
irq = pdev->irq;
ioaddr = ioremap(base, 0x400);
diff --git a/drivers/net/ne2k-pci.c b/drivers/net/ne2k-pci.c
index ced9fdb..b5bf53f 100644
--- a/drivers/net/ne2k-pci.c
+++ b/drivers/net/ne2k-pci.c
@@ -231,12 +231,14 @@ #endif
irq = pdev->irq;
if (!ioaddr || ((pci_resource_flags (pdev, 0) & IORESOURCE_IO) == 0)) {
- printk (KERN_ERR PFX "no I/O resource at PCI BAR #0\n");
+ dev_printk (KERN_ERR, &pdev->dev,
+ "no I/O resource at PCI BAR #0\n");
return -ENODEV;
}
if (request_region (ioaddr, NE_IO_EXTENT, DRV_NAME) == NULL) {
- printk (KERN_ERR PFX "I/O resource 0x%x @ 0x%lx busy\n",
+ dev_printk (KERN_ERR, &pdev->dev,
+ "I/O resource 0x%x @ 0x%lx busy\n",
NE_IO_EXTENT, ioaddr);
return -EBUSY;
}
@@ -263,7 +265,8 @@ #endif
/* Allocate net_device, dev->priv; fill in 8390 specific dev fields. */
dev = alloc_ei_netdev();
if (!dev) {
- printk (KERN_ERR PFX "cannot allocate ethernet device\n");
+ dev_printk (KERN_ERR, &pdev->dev,
+ "cannot allocate ethernet device\n");
goto err_out_free_res;
}
SET_MODULE_OWNER(dev);
@@ -281,7 +284,8 @@ #endif
while ((inb(ioaddr + EN0_ISR) & ENISR_RESET) == 0)
/* Limit wait: '2' avoids jiffy roll-over. */
if (jiffies - reset_start_time > 2) {
- printk(KERN_ERR PFX "Card failure (no reset
ack).\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "Card failure (no reset ack).\n");
goto err_out_free_netdev;
}
diff --git a/drivers/net/ns83820.c b/drivers/net/ns83820.c
index 706aed7..916ec99 100644
--- a/drivers/net/ns83820.c
+++ b/drivers/net/ns83820.c
@@ -1833,7 +1833,8 @@ static int __devinit ns83820_init_one(st
} else if (!pci_set_dma_mask(pci_dev, DMA_32BIT_MASK)) {
using_dac = 0;
} else {
- printk(KERN_WARNING "ns83820.c: pci_set_dma_mask failed!\n");
+ dev_printk(KERN_WARNING, &pci_dev->dev,
+ "pci_set_dma_mask failed!\n");
return -ENODEV;
}
@@ -1856,7 +1857,8 @@ static int __devinit ns83820_init_one(st
err = pci_enable_device(pci_dev);
if (err) {
- printk(KERN_INFO "ns83820: pci_enable_dev failed: %d\n", err);
+ dev_printk(KERN_INFO, &pci_dev->dev,
+ "pci_enable_dev failed: %d\n", err);
goto out_free;
}
@@ -1885,8 +1887,9 @@ static int __devinit ns83820_init_one(st
err = request_irq(pci_dev->irq, ns83820_irq, SA_SHIRQ,
DRV_NAME, ndev);
if (err) {
- printk(KERN_INFO "ns83820: unable to register irq %d\n",
- pci_dev->irq);
+ dev_printk(KERN_INFO, &pci_dev->dev,
+ "unable to register irq %d, err %d\n",
+ pci_dev->irq, err);
goto out_disable;
}
@@ -1900,7 +1903,8 @@ static int __devinit ns83820_init_one(st
rtnl_lock();
err = dev_alloc_name(ndev, ndev->name);
if (err < 0) {
- printk(KERN_INFO "ns83820: unable to get netdev name: %d\n",
err);
+ dev_printk(KERN_INFO, &pci_dev->dev,
+ "unable to get netdev name: %d\n", err);
goto out_free_irq;
}
diff --git a/drivers/net/pci-skeleton.c b/drivers/net/pci-skeleton.c
index a7bb54d..2754fad 100644
--- a/drivers/net/pci-skeleton.c
+++ b/drivers/net/pci-skeleton.c
@@ -602,7 +602,8 @@ static int __devinit netdrv_init_board (
/* dev zeroed in alloc_etherdev */
dev = alloc_etherdev (sizeof (*tp));
if (dev == NULL) {
- printk (KERN_ERR PFX "unable to alloc new ethernet\n");
+ dev_printk (KERN_ERR, &pdev->dev,
+ "unable to alloc new ethernet\n");
DPRINTK ("EXIT, returning -ENOMEM\n");
return -ENOMEM;
}
@@ -632,14 +633,16 @@ static int __devinit netdrv_init_board (
/* make sure PCI base addr 0 is PIO */
if (!(pio_flags & IORESOURCE_IO)) {
- printk (KERN_ERR PFX "region #0 not a PIO resource,
aborting\n");
+ dev_printk (KERN_ERR, &pdev->dev,
+ "region #0 not a PIO resource, aborting\n");
rc = -ENODEV;
goto err_out;
}
/* make sure PCI base addr 1 is MMIO */
if (!(mmio_flags & IORESOURCE_MEM)) {
- printk (KERN_ERR PFX "region #1 not an MMIO resource,
aborting\n");
+ dev_printk (KERN_ERR, &pdev->dev,
+ "region #1 not an MMIO resource, aborting\n");
rc = -ENODEV;
goto err_out;
}
@@ -647,12 +650,13 @@ static int __devinit netdrv_init_board (
/* check for weird/broken PCI region reporting */
if ((pio_len < NETDRV_MIN_IO_SIZE) ||
(mmio_len < NETDRV_MIN_IO_SIZE)) {
- printk (KERN_ERR PFX "Invalid PCI region size(s), aborting\n");
+ dev_printk (KERN_ERR, &pdev->dev,
+ "Invalid PCI region size(s), aborting\n");
rc = -ENODEV;
goto err_out;
}
- rc = pci_request_regions (pdev, "pci-skeleton");
+ rc = pci_request_regions (pdev, MODNAME);
if (rc)
goto err_out;
@@ -664,7 +668,8 @@ #else
/* ioremap MMIO region */
ioaddr = ioremap (mmio_start, mmio_len);
if (ioaddr == NULL) {
- printk (KERN_ERR PFX "cannot remap MMIO, aborting\n");
+ dev_printk (KERN_ERR, &pdev->dev,
+ "cannot remap MMIO, aborting\n");
rc = -EIO;
goto err_out_free_res;
}
@@ -700,9 +705,10 @@ #endif /* !USE_IO_OPS */
}
/* if unknown chip, assume array element #0, original RTL-8139 in this
case */
- printk (KERN_DEBUG PFX "PCI device %s: unknown chip version, assuming
RTL-8139\n",
- pci_name(pdev));
- printk (KERN_DEBUG PFX "PCI device %s: TxConfig = 0x%lx\n",
pci_name(pdev), NETDRV_R32 (TxConfig));
+ dev_printk (KERN_DEBUG, &pdev->dev,
+ "unknown chip version, assuming RTL-8139\n");
+ dev_printk (KERN_DEBUG, &pdev->dev, "TxConfig = 0x%lx\n",
+ NETDRV_R32 (TxConfig));
tp->chipset = 0;
match:
diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c
index 12d1cb2..24a5b31 100644
--- a/drivers/net/r8169.c
+++ b/drivers/net/r8169.c
@@ -1406,7 +1406,8 @@ rtl8169_init_board(struct pci_dev *pdev,
dev = alloc_etherdev(sizeof (*tp));
if (dev == NULL) {
if (netif_msg_drv(&debug))
- printk(KERN_ERR PFX "unable to alloc new ethernet\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "unable to alloc new ethernet\n");
goto err_out;
}
@@ -1418,10 +1419,8 @@ rtl8169_init_board(struct pci_dev *pdev,
/* enable device (incl. PCI PM wakeup and hotplug setup) */
rc = pci_enable_device(pdev);
if (rc < 0) {
- if (netif_msg_probe(tp)) {
- printk(KERN_ERR PFX "%s: enable failure\n",
- pci_name(pdev));
- }
+ if (netif_msg_probe(tp))
+ dev_printk(KERN_ERR, &pdev->dev, "enable failure\n");
goto err_out_free_dev;
}
@@ -1437,37 +1436,33 @@ rtl8169_init_board(struct pci_dev *pdev,
pci_read_config_word(pdev, pm_cap + PCI_PM_CTRL, &pwr_command);
acpi_idle_state = pwr_command & PCI_PM_CTRL_STATE_MASK;
} else {
- if (netif_msg_probe(tp)) {
- printk(KERN_ERR PFX
+ if (netif_msg_probe(tp))
+ dev_printk(KERN_ERR, &pdev->dev,
"PowerManagement capability not found.\n");
- }
}
/* make sure PCI base addr 1 is MMIO */
if (!(pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) {
- if (netif_msg_probe(tp)) {
- printk(KERN_ERR PFX
+ if (netif_msg_probe(tp))
+ dev_printk(KERN_ERR, &pdev->dev,
"region #1 not an MMIO resource, aborting\n");
- }
rc = -ENODEV;
goto err_out_mwi;
}
/* check for weird/broken PCI region reporting */
if (pci_resource_len(pdev, 1) < R8169_REGS_SIZE) {
- if (netif_msg_probe(tp)) {
- printk(KERN_ERR PFX
+ if (netif_msg_probe(tp))
+ dev_printk(KERN_ERR, &pdev->dev,
"Invalid PCI region size(s), aborting\n");
- }
rc = -ENODEV;
goto err_out_mwi;
}
rc = pci_request_regions(pdev, MODULENAME);
if (rc < 0) {
- if (netif_msg_probe(tp)) {
- printk(KERN_ERR PFX "%s: could not request regions.\n",
- pci_name(pdev));
- }
+ if (netif_msg_probe(tp))
+ dev_printk(KERN_ERR, &pdev->dev,
+ "could not request regions.\n");
goto err_out_mwi;
}
@@ -1480,10 +1475,9 @@ rtl8169_init_board(struct pci_dev *pdev,
} else {
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (rc < 0) {
- if (netif_msg_probe(tp)) {
- printk(KERN_ERR PFX
+ if (netif_msg_probe(tp))
+ dev_printk(KERN_ERR, &pdev->dev,
"DMA configuration failed.\n");
- }
goto err_out_free_res;
}
}
@@ -1494,7 +1488,8 @@ rtl8169_init_board(struct pci_dev *pdev,
ioaddr = ioremap(pci_resource_start(pdev, 1), R8169_REGS_SIZE);
if (ioaddr == NULL) {
if (netif_msg_probe(tp))
- printk(KERN_ERR PFX "cannot remap MMIO, aborting\n");
+ dev_printk(KERN_ERR, &pdev->dev,
+ "cannot remap MMIO, aborting\n");
rc = -EIO;
goto err_out_free_res;
}
@@ -1526,9 +1521,9 @@ rtl8169_init_board(struct pci_dev *pdev,
if (i < 0) {
/* Unknown chip: assume array element #0, original RTL-8169 */
if (netif_msg_probe(tp)) {
- printk(KERN_DEBUG PFX "PCI device %s: "
+ dev_printk(KERN_DEBUG, &pdev->dev,
"unknown chip version, assuming %s\n",
- pci_name(pdev), rtl_chip_info[0].name);
+ rtl_chip_info[0].name);
}
i++;
}
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
