The Switches use GPIO lines to indicate interrupts from two of the switches.
With these interrupts in place, we can make use of the interrupt
controllers within the switch to indicate when the internal PHYs
generate an interrupt. Use standard PHY properties to do this.
Signed-off-by: Andrew Lunn <and...@lunn.ch>
---
arch/arm/boot/dts/vf610-zii-dev-rev-b.dts | 51 +++++++++++++++++++++++++++++++
1 file changed, 51 insertions(+)
diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
index 5c1fcab4a6f7..1a9b4ad138f6 100644
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
+++ b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
@@ -88,10 +88,16 @@
switch0: switch0@0 {
compatible = "marvell,mv88e6085";
+ pinctrl-0 = <&pinctrl_gpio_switch0>;
+ pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
dsa,member = <0 0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
ports {
#address-cells = <1>;
@@ -99,16 +105,19 @@
port@0 {
reg = <0>;
label = "lan0";
+ phy-handle = <&switch0phy0>;
};
port@1 {
reg = <1>;
label = "lan1";
+ phy-handle = <&switch0phy1>;
};
port@2 {
reg = <2>;
label = "lan2";
+ phy-handle = <&switch0phy2>;
};
switch0port5: port@5 {
@@ -133,6 +142,24 @@
};
};
};
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ switch0phy0: switch0phy0@0 {
+ reg = <0>;
+ interrupt-parent = <&switch0>;
+ interrupts = <0
IRQ_TYPE_LEVEL_HIGH>;
+ };
+ switch0phy1: switch1phy0@1 {
+ reg = <1>;
+ interrupt-parent = <&switch0>;
+ interrupts = <1
IRQ_TYPE_LEVEL_HIGH>; };
+ switch0phy2: switch1phy0@2 {
+ reg = <2>;
+ interrupt-parent = <&switch0>;
+ interrupts = <2
IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
};
};
@@ -143,10 +170,16 @@
switch1: switch1@0 {
compatible = "marvell,mv88e6085";
+ pinctrl-0 = <&pinctrl_gpio_switch1>;
+ pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
dsa,member = <0 1>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
ports {
#address-cells = <1>;
@@ -196,12 +229,18 @@
#size-cells = <0>;
switch1phy0: switch1phy0@0 {
reg = <0>;
+ interrupt-parent = <&switch1>;
+ interrupts = <0
IRQ_TYPE_LEVEL_HIGH>;
};
switch1phy1: switch1phy0@1 {
reg = <1>;
+ interrupt-parent = <&switch1>;
+ interrupts = <2
IRQ_TYPE_LEVEL_HIGH>;
};
switch1phy2: switch1phy0@2 {
reg = <2>;
+ interrupt-parent = <&switch1>;
+ interrupts = <2
IRQ_TYPE_LEVEL_HIGH>;
};
};
};
@@ -636,6 +675,18 @@
>;
};
+ pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
+ fsl,pins = <
+ VF610_PAD_PTB5__GPIO_27 0x219d
+ >;
+ };
+
+ pinctrl_gpio_switch1: pinctrl-gpio-switch1 {
+ fsl,pins = <
+ VF610_PAD_PTB4__GPIO_26 0x219d
+ >;
+ };
+
pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset {
fsl,pins = <
VF610_PAD_PTE14__GPIO_119 0x31c2
--
2.9.3
