I've got a cf card running as a secondary drive on a Sparc Ultra 5 (Sparc64),
but have not been able to get it to boot. The cf/ide plug I am using has no
master/slave/cs sets and a microprocessor on it as well, which leaves me
suspicious
of it because the CF interface is sposed to be a shrunken IDE.
The sparc boot diags (probe-ide) show no device other than an ide hdd if it is
attached.
Also, I have experience that IDE disks are addressable after boot if the
CS/MS/SL is
set wrong (that is they can have mountable file systems) but will still not be
bootable
themselves, which further leads me to believe the CF card 2 IDE plug I have is
useless
for this.
But I mebbe barking up the wrong tree altogether here and it is just not
doable...
Comments/ideas anyone?
Thanks,
Dhu
p.s.
# dmesg
console is keyboard/display
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2009 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 4.5 (GENERIC) #1898: Sat Feb 28 17:42:44 MST 2009
[email protected]:/usr/src/sys/arch/sparc64/compile/GENERIC
real mem = 536870912 (512MB)
avail mem = 507625472 (484MB)
mainbus0 at root: Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 270MHz)
cpu0 at mainbus0: SUNW,UltraSPARC-IIi (rev 1.3) @ 270 MHz
cpu0: physical 16K instruction (32 b/l), 16K data (32 b/l), 256K external (64
b/l)
psycho0 at mainbus0 addr 0xfffc4000: SUNW,sabre, impl 0, version 0, ign 7c0
psycho0: bus range 0-3, PCI bus 0
psycho0: dvma map c0000000-dfffffff
pci0 at psycho0
ppb0 at pci0 dev 1 function 1 "Sun Simba PCI-PCI" rev 0x13
pci1 at ppb0 bus 1
ebus0 at pci1 dev 1 function 0 "Sun PCIO EBus2" rev 0x01
auxio0 at ebus0 addr 726000-726003, 728000-728003, 72a000-72a003,
72c000-72c003, 72f000-72f003
power0 at ebus0 addr 724000-724003 ivec 0x25
"SUNW,pll" at ebus0 addr 504000-504002 not configured
sab0 at ebus0 addr 400000-40007f ivec 0x2b: rev 3.2
sabtty0 at sab0 port 0
sabtty1 at sab0 port 1
comkbd0 at ebus0 addr 3083f8-3083ff ivec 0x29: layout 34
wskbd0 at comkbd0: console keyboard
com0 at ebus0 addr 3062f8-3062ff ivec 0x2a: mouse: ns16550a, 16 byte fifo
lpt0 at ebus0 addr 3043bc-3043cb, 30015c-30015d, 700000-70000f ivec 0x22: polled
clock1 at ebus0 addr 0-1fff: mk48t59
"flashprom" at ebus0 addr 0-fffff not configured
audioce0 at ebus0 addr 200000-2000ff, 702000-70200f, 704000-70400f,
722000-722003 ivec 0x23 ivec 0x24: nvaddrs 0
audio0 at audioce0
hme0 at pci1 dev 1 function 1 "Sun HME" rev 0x01: ivec 0x7e1, address
08:00:20:a2:f6:94
nsphy0 at hme0 phy 1: DP83840 10/100 PHY, rev. 1
vgafb0 at pci1 dev 2 function 0 "ATI Mach64" rev 0x5c
wsdisplay0 at vgafb0 mux 1: console (std, sun emulation), using wskbd0
pciide0 at pci1 dev 3 function 0 "CMD Technology PCI0646" rev 0x03: DMA,
channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using ivec 0x7e0 for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <WDC AC28400R>
wd0: 16-sector PIO, LBA, 8063MB, 16514064 sectors
wd0(pciide0:0:0): using PIO mode 4
wd1 at pciide0 channel 1 drive 1: <ELITE PRO CF CARD 16GB>
wd1: 1-sector PIO, LBA, 15280MB, 31293440 sectors
wd1(pciide0:1:1): using PIO mode 4
ppb1 at pci0 dev 1 function 0 "Sun Simba PCI-PCI" rev 0x13
pci2 at ppb1 bus 2
ppb2 at pci2 dev 1 function 0 "DEC 21152 PCI-PCI" rev 0x02
pci3 at ppb2 bus 3
"Sun PCIO EBus2" rev 0x01 at pci3 dev 0 function 0 not configured
hme1 at pci3 dev 0 function 1 "Sun HME" rev 0x01: ivec 0x7d1, address
08:00:20:a3:e8:52
nsphy1 at hme1 phy 1: DP83840 10/100 PHY, rev. 1
isp0 at pci3 dev 4 function 0 "QLogic ISP1020" rev 0x05: ivec 0x7d0
isp0: invalid NVRAM header
scsibus0 at isp0: 16 targets, initiator 7
softraid0 at root
bootpath: /p...@1f,0/p...@1,1/i...@3,0/d...@0,0
root on wd0a swap on wd0b dump on wd0b
# mount
/dev/wd0a on / type ffs (local)
/dev/wd1a on /mnt type ffs (local)
/dev/wd1d on /mnt2 type ffs (local)
# df
Filesystem 512-blocks Used Avail Capacity Mounted on
/dev/wd0a 14444316 2170316 11551788 16% /
/dev/wd1a 8251788 2180244 5658956 28% /mnt
/dev/wd1d 20471612 2234052 17213980 11% /mnt2
