On Wed, Jul 29, 2009 at 09:41:01PM -0700, Justin Martz wrote: > Hello. Sorry if this is the wrong list! I'm trying to get my OpenBSD laptop > online. I have an HP Special Edition L2000 running 4.5 GENERIC. I bought a > Linksys Wireless-G Ver 2 PCMCIA card, which the man page for bwi says is > supported by the driver:
why do you bought a broadcom wireless card? i have several rum cards and they are chip and work very well. have you loaded the firmware needed by bwi? > > Linksys WPC54G Ver 3 BCM4318 CardBus b/g > Linksys WPC54GS Ver 2 BCM4318 CardBus b/g > > When I boot OpenBSD it only sees the embedded wireless and not the card. > > From dmesg, without Linksys card: > bwi0 at pci2 dev 2 function 0 "Broadcom BCM4318" rev 0x02: apic 1 int 20 (irq > 3), address 00:90:4b:f8:43:ea > cbb0 at pci2 dev 9 function 0 "TI PCI7XX1 CardBus" rev 0x00: apic 1 int 17 > (irq 255), CardBus support disabled > > Seeing that "Broadcom BCM4318" match up with the line in the man page I > figured the embedded might work, but 'ifconfig bwi0 up' gives me: > bwi0: base tssi measure failed > > but the little blue light for the embedded wireless turns on. When I do > 'ifconfig bwi0 down' the light turns off, but no messages. > > > This is what I get after I plug in the Linksys card: > cardslot0: CardBus support disabled > > It's the same line in dmesg whether the card is in or not. > > The man page for boot_config gives an example of what to do when you can't > find an Ethernet card, and how to change the IRQ. Could it just be some sort > of conflict? Why would CardBus support be disabled? There is an option in > the BIOS to enable or disable the embedded wireless and I've tried it both > ways. I'm new to OpenBSD and would appreciate any help. > > Here's the whole dmesg output: > OpenBSD 4.5 (GENERIC) #2052: Sat Feb 28 14:55:24 MST 2009 > [email protected]:/usr/src/sys/arch/amd64/compile/GENERIC > real mem = 937361408 (893MB) > avail mem = 897474560 (855MB) > mainbus0 at root > bios0 at mainbus0: SMBIOS rev. 2.31 @ 0xdc010 (18 entries) > bios0: vendor Hewlett-Packard version "F.22" date 01/02/2006 > bios0: Hewlett-Packard Presario V2000 (EP378UA#ABA) > acpi at bios0 not configured > mpbios0 at bios0: Intel MP Specification 1.4 > cpu0 at mainbus0: apid 0 (boot processor) > cpu0: AMD Turion(tm) 64 Mobile Technology ML-34, 1795.09 MHz > cpu0: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS > H,MMX,FXSR,SSE,SSE2,SSE3,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW > cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 1MB 64b/line > 16-way L2 cache > cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu0: AMD erratum 89 present, BIOS upgrade may be required > cpu0: apic clock running at 199MHz > mpbios0: bus 0 is type PCI > mpbios0: bus 1 is type PCI > mpbios0: bus 2 is type PCI > mpbios0: bus 3 is type PCI > mpbios0: bus 4 is type PCI > mpbios0: bus 5 is type PCI > mpbios0: bus 6 is type ISA > ioapic0 at mainbus0 apid 1 pa 0xfec00000, version 21, 24 pins > cpu0: PowerNow! K8 1795 MHz: speeds: 1800 1600 800 MHz > pci0 at mainbus0 bus 0: configuration mode 1 > pchb0 at pci0 dev 0 function 0 "ATI RS480 Host" rev 0x01 > ppb0 at pci0 dev 1 function 0 "ATI RS480 PCIE" rev 0x00 > pci1 at ppb0 bus 1 > vga1 at pci1 dev 5 function 0 "ATI Radeon XPRESS 200M" rev 0x00 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > ohci0 at pci0 dev 19 function 0 "ATI SB400 USB" rev 0x00: apic 1 int 19 (irq > 11), version 1.0, legacy support > ohci1 at pci0 dev 19 function 1 "ATI SB400 USB" rev 0x00: apic 1 int 19 (irq > 11), version 1.0, legacy support > ehci0 at pci0 dev 19 function 2 "ATI SB400 USB2" rev 0x00: apic 1 int 19 (irq > 11) > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1 > piixpm0 at pci0 dev 20 function 0 "ATI SB400 SMBus" rev 0x11: SMI > iic0 at piixpm0 > spdmem0 at iic0 addr 0x50: 512MB DDR SDRAM non-parity PC2700CL2.5 > spdmem1 at iic0 addr 0x51: 512MB DDR SDRAM non-parity PC2700CL2.5 > pciide0 at pci0 dev 20 function 1 "ATI SB400 IDE" rev 0x00: DMA, channel 0 > configured to compatibility, channel 1 configured to compatibility > wd0 at pciide0 channel 0 drive 0: <FUJITSU MHU2100AT> > wd0: 16-sector PIO, LBA, 95396MB, 195371568 sectors > wd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 > atapiscsi0 at pciide0 channel 1 drive 0 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <TSSTcorp, CD/DVDW TS-L532R, HA05> ATAPI 5/cdrom > removable > cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 > pcib0 at pci0 dev 20 function 3 "ATI SB400 ISA" rev 0x00 > ppb1 at pci0 dev 20 function 4 "ATI SB400 PCI" rev 0x00 > pci2 at ppb1 bus 5 > rl0 at pci2 dev 0 function 0 "Realtek 8139" rev 0x10: apic 1 int 18 (irq 5), > address 00:16:36:22:b1:5f > rlphy0 at rl0 phy 0: RTL internal PHY > bwi0 at pci2 dev 2 function 0 "Broadcom BCM4318" rev 0x02: apic 1 int 20 (irq > 3), address 00:90:4b:f8:43:ea > cbb0 at pci2 dev 9 function 0 "TI PCI7XX1 CardBus" rev 0x00: apic 1 int 17 > (irq 255), CardBus support disabled > "TI PCI7XX1 FireWire" rev 0x00 at pci2 dev 9 function 2 not configured > "TI PCI7XX1 Flash" rev 0x00 at pci2 dev 9 function 3 not configured > sdhc0 at pci2 dev 9 function 4 "TI PCI7XX1 Secure Data" rev 0x00: apic 1 int > 17 (irq 10) > sdmmc0 at sdhc0 > sdmmc1 at sdhc0 > sdmmc2 at sdhc0 > cardslot0 at cbb0 slot 0 flags 0 > pcmcia0 at cardslot0 > auixp0 at pci0 dev 20 function 5 "ATI SB400 AC97" rev 0x02: apic 1 int 17 (irq > 10) > auixp0: soft resetting aclink > "ATI SB400 Modem" rev 0x02 at pci0 dev 20 function 6 not configured > pchb1 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00 > pchb2 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00 > pchb3 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00 > kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00 > usb1 at ohci0: USB revision 1.0 > uhub1 at usb1 "ATI OHCI root hub" rev 1.00/1.00 addr 1 > usb2 at ohci1: USB revision 1.0 > uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1 > isa0 at pcib0 > isadma0 at isa0 > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pmsi0 at pckbc0 (aux slot) > pckbc0: using irq 12 for aux slot > wsmouse0 at pmsi0 mux 0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > mtrr: Pentium Pro MTRR support > softraid0 at root > root on wd0a swap on wd0b dump on wd0b > ac97: codec id 0x43585430 (Conexant CXT48) > ac97: codec features reserved, headphone, 18 bit DAC, 18 bit ADC, No 3D > Stereo > audio0 at auixp0 > maybe you can try sending a dmesg after you try ifconfig bwi0 up. -- DISCLAIMER: http://goldmark.org/jeff/stupid-disclaimers/ This message will self-destruct in 3 seconds.
