Yes, actually I have read this "man biosboot", but the point is I don't know how to resolve this issue :-(.
2009/5/10 patrick keshishian <[email protected]> > man biosboot > /ERR M > > > On Sat, May 9, 2009 at 2:19 AM, Feifei (7I7I) <[email protected]> wrote: > > Hi, guys, > > > > I installed the OpenBSD 4.5 some days ago, but boot failed after all > > installation were completed. I flag the partition of OpenBSD bootable > ,but > > only get > > "loading ... > > ERR M" > > error code, > > > > I try to flag my Windows partition bootable and use ntldr to load > > openbsd.pbr (dd if=/dev/rwd0a of=openbsd.pbr bs=512 count=1), but also > get > > the some error warning. > > > > But, before that, the OpenBSD 4.2 works well in this laptop ( compaq > > presario M2000, with Interl Cerleron M 1.5GHz, 915 Chipest) > > > > I don't know how to share my .pbr , so I upload it to www.box.net , the > file > > direct downlink is http://www.box.net/shared/qzlzz69xy9 , you can > download > > it without regesiter or installing any activex/add-ons/plugin. > > ===================================== > > This is my partition table: > > > > Disk: /dev/rwd0c geometry: 4864/255/63 [78140160 Sectors] > > Offset: 0 Signature: 0xAA55 > > Starting Ending LBA Info: > > #: id C H S - C H S [ start: size ] > > > ----------------------------------------------------------------------------- -- > > 0: 07 0 1 1 - 636 254 63 [ 63: 10233342 ] > > HPFS/QNX/AUX > > 1: 0F 637 0 1 - 4461 254 63 [ 10233405: 61448625 ] > Extended > > LBA > > *2: A6 4462 0 1 - 4863 254 63 [ 71682030: 6458130 ] > > OpenBSD > > 3: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > Offset: 10233405 Signature: 0xAA55 > > Starting Ending LBA Info: > > #: id C H S - C H S [ start: size ] > > > ----------------------------------------------------------------------------- -- > > 0: 07 637 1 1 - 1911 254 63 [ 10233468: 20482812 ] > > HPFS/QNX/AUX > > 1: 05 1912 0 1 - 3823 254 63 [ 30716280: 30716280 ] > Extended > > DOS > > 2: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > 3: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > Offset: 30716280 Signature: 0xAA55 > > Starting Ending LBA Info: > > #: id C H S - C H S [ start: size ] > > > ----------------------------------------------------------------------------- -- > > 0: 07 1912 1 1 - 3823 254 63 [ 30716343: 30716217 ] > > HPFS/QNX/AUX > > 1: 05 3824 0 1 - 4370 254 63 [ 61432560: 8787555 ] > Extended > > DOS > > 2: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > 3: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > Offset: 61432560 Signature: 0xAA55 > > Starting Ending LBA Info: > > #: id C H S - C H S [ start: size ] > > > ----------------------------------------------------------------------------- -- > > 0: 83 3824 1 1 - 4370 254 63 [ 61432623: 8787492 ] Linux > > files* > > 1: 05 4371 0 1 - 4461 254 63 [ 70220115: 1461915 ] > Extended > > DOS > > 2: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > 3: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > Offset: 70220115 Signature: 0xAA55 > > Starting Ending LBA Info: > > #: id C H S - C H S [ start: size ] > > > ----------------------------------------------------------------------------- -- > > 0: 82 4371 1 1 - 4461 254 63 [ 70220178: 1461852 ] Linux > > swap > > 1: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > 2: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > 3: 00 0 0 0 - 0 0 0 [ 0: 0 ] > > unused > > > > > > > > > > > > =================================== > > This is my dmesg.txt > > > > > > OpenBSD 4.5 (RAMDISK_CD) #1112: Sat Feb 28 15:06:26 MST 2009 > > [email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD > > cpu0: Intel(R) Celeron(R) M processor 1.50GHz ("GenuineIntel" 686-class) > > 1.50 GHz > > cpu0: > > > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,A CPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF > > real mem = 1063743488 (1014MB) > > avail mem = 1021931520 (974MB) > > mainbus0 at root > > bios0 at mainbus0: AT/286+ BIOS, date 12/22/05, BIOS32 rev. 0 @ 0xfd710, > > SMBIOS rev. 2.31 @ 0xdf010 (19 entries) > > bios0: vendor Hewlett-Packard version "F.21" date 12/22/2005 > > bios0: Hewlett-Packard Presario M2000 (PY845PA#AB2) > > acpi0 at bios0: rev 0 > > acpi0: tables DSDT APIC FACP HPET MCFG BOOT SSDT SSDT > > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat > > cpu0 at mainbus0: apid 0 (boot processor) > > cpu0: apic clock running at 99MHz > > ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins > > ioapic0: misconfigured as apic 0, remapped to apid 1 > > acpiprt0 at acpi0: bus 0 (PCI0) > > acpiprt1 at acpi0: bus 6 (PCIB) > > bios0: ROM list: 0xc0000/0xf200! 0xcf800/0x1000 0xdf000/0x800! > > 0xe0000/0x4000! > > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > > pchb0 at pci0 dev 0 function 0 "Intel 82915GM Host" rev 0x03 > > vga1 at pci0 dev 2 function 0 "Intel 82915GM Video" rev 0x03 > > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > > "Intel 82915GM Video" rev 0x03 at pci0 dev 2 function 1 not configured > > uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x03: apic 1 int > 23 > > (irq 3) > > uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x03: apic 1 int > 19 > > (irq 3) > > uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x03: apic 1 int > 18 > > (irq 4) > > uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x03: apic 1 int > 16 > > (irq 10) > > ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x03: apic 1 int > 23 > > (irq 3) > > usb0 at ehci0: USB revision 2.0 > > uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 > > ppb0 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd3 > > pci1 at ppb0 bus 6 > > rl0 at pci1 dev 0 function 0 "Realtek 8139" rev 0x10: apic 1 int 16 (irq > > 10), address 00:c0:9f:a2:cd:9d > > rlphy0 at rl0 phy 0: RTL internal PHY > > bwi0 at pci1 dev 6 function 0 "Broadcom BCM4306" rev 0x03: apic 1 int 18 > > (irq 4), address 00:90:4b:a5:04:f5 > > cbb0 at pci1 dev 9 function 0 "TI PCI7XX1 CardBus" rev 0x00: apic 1 int > 20 > > (irq 255), CardBus support disabled > > "TI PCI7XX1 FireWire" rev 0x00 at pci1 dev 9 function 2 not configured > > "TI PCI7XX1 Flash" rev 0x00 at pci1 dev 9 function 3 not configured > > "TI PCI7XX1 Secure Data" rev 0x00 at pci1 dev 9 function 4 not configured > > cardslot0 at cbb0 slot 0 flags 0 > > pcmcia0 at cardslot0 > > "Intel 82801FB AC97" rev 0x03 at pci0 dev 30 function 2 not configured > > "Intel 82801FB Modem" rev 0x03 at pci0 dev 30 function 3 not configured > > ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x03: PM > > disabled > > pciide0 at pci0 dev 31 function 1 "Intel 82801FB IDE" rev 0x03: DMA, > channel > > 0 configured to compatibility, channel 1 configured to compatibility > > wd0 at pciide0 channel 0 drive 0: <HTS424040M9AT00> > > wd0: 16-sector PIO, LBA, 38154MB, 78140160 sectors > > atapiscsi0 at pciide0 channel 0 drive 1 > > scsibus0 at atapiscsi0: 2 targets > > cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, RW/DVD GCC-4244N, 1.01> ATAPI > > 5/cdrom removable > > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 > > cd0(pciide0:0:1): using PIO mode 4, DMA mode 2 > > pciide0: channel 1 ignored (disabled) > > "Intel 82801FB SMBus" rev 0x03 at pci0 dev 31 function 3 not configured > > usb1 at uhci0: USB revision 1.0 > > uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > > usb2 at uhci1: USB revision 1.0 > > uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > > usb3 at uhci2: USB revision 1.0 > > uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > > usb4 at uhci3: USB revision 1.0 > > uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > > isa0 at ichpcib0 > > isadma0 at isa0 > > pckbc0 at isa0 port 0x60/5 > > pckbd0 at pckbc0 (kbd slot) > > pckbc0: using irq 1 for kbd slot > > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > > rd0: fixed, 3800 blocks > > uhidev0 at uhub2 port 1 configuration 1 interface 0 "vendor 0x0461 USB > > Optical Mouse" rev 2.00/2.00 addr 2 > > uhidev0: iclass 3/1 > > uhid at uhidev0 not configured > > softraid0 at root > > root on rd0a swap on rd0b dump on rd0b > > umass0 at uhub0 port 2 configuration 1 interface 0 "TREK TDMINIG4" rev > > 2.00/1.00 addr 2 > > umass0: using SCSI over Bulk-Only > > scsibus1 at umass0: 2 targets, initiator 0 > > sd0 at scsibus1 targ 1 lun 0: <TREK, TDMINIG4, 1.00> SCSI2 0/direct > > removable > > sd0: 963MB, 512 bytes/sec, 1974271 sec total > > sd0 detached > > scsibus1 detached > > umass0 detached > > umass0 at uhub0 port 2 configuration 1 interface 0 "TREK TDMINIG4" rev > > 2.00/1.00 addr 2 > > umass0: using SCSI over Bulk-Only > > scsibus1 at umass0: 2 targets, initiator 0 > > sd0 at scsibus1 targ 1 lun 0: <TREK, TDMINIG4, 1.00> SCSI2 0/direct > > removable > > sd0: 963MB, 512 bytes/sec, 1974271 sec total > > sd0 detached > > scsibus1 detached > > umass0 detached > > umass0 at uhub0 port 2 configuration 1 interface 0 "TREK TDMINIG4" rev > > 2.00/1.00 addr 2 > > umass0: using SCSI over Bulk-Only > > scsibus1 at umass0: 2 targets, initiator 0 > > sd0 at scsibus1 targ 1 lun 0: <TREK, TDMINIG4, 1.00> SCSI2 0/direct > > removable > > sd0: 963MB, 512 bytes/sec, 1974271 sec total
