Hi list,
Like the subject implies - I would like to know how long it should take for
a fsck to check a 300GB hdd. I think that my pc's fsck is checking a 300GB
for too long - about 45 minutes. And during install it took approximately
the same amount of time to format it. Is this normal?
Here is my dmesg:
OpenBSD 4.4 (GENERIC) #1021: Tue Aug 12 17:16:55 MDT 2008
[email protected]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Sempron(tm) Processor LE-1250 ("AuthenticAMD" 686-class, 512KB L2
cache) 2.21 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLU
SH,MMX,FXSR,SSE,SSE2,SSE3,CX16
real mem = 468152320 (446MB)
avail mem = 444112896 (423MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 04/17/08, BIOS32 rev. 0 @ 0xfb7c0,
SMBIOS rev. 2.4 @ 0xf0100 (46 entries)
bios0: vendor Award Software International, Inc. version "F1" date
04/17/2008
bios0: Gigabyte Technology Co., Ltd. GA-MA74GM-S2
apm0 at bios0: Power Management spec V1.2 (slowidle)
apm0: AC on, battery charge unknown
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 3.0 @ 0xf0000/0xdba4
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfda90/272 (15 entries)
pcibios0: bad IRQ table checksum
pcibios0: PCI BIOS has 15 Interrupt Routing table entries
pcibios0: PCI Exclusive IRQs: 3 4 5 7 10 11
pcibios0: no compatible PCI ICU found
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #3 is the last bus
bios0: ROM list: 0xc0000/0xd800
cpu0 at mainbus0
cpu0: PowerNow! K8 2205 MHz: speeds: 2200 2000 1800 1000 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ATI RS740 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "ATI RS690 PCIE" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon 2100" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
drm at vga1 unsupported
ppb1 at pci0 dev 6 function 0 "ATI RS690 PCIE" rev 0x00
pci2 at ppb1 bus 2
re0 at pci2 dev 0 function 0 "Realtek 8168" rev 0x02: RTL8168C/8111C
(0x3c00), irq 10, address 00:1f:d0:9b:9b:d3
rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2
pciide0 at pci0 dev 17 function 0 "ATI IXPx00 SATA" rev 0x00: DMA
(unsupported), channel 0 configured to native-PCI, channel 1 configured to
native-PCI
pciide0: using irq 11 for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <SAMSUNG HD322HJ>
wd0: 16-sector PIO, LBA48, 305244MB, 625140335 sectors
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets, initiator 7
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GH22NS40, NL00> ATAPI
5/cdrom removable
pciide0: channel 1 ignored (not responding; disabled or no drives?)
ohci0 at pci0 dev 18 function 0 "ATI IXP700 USB" rev 0x00: irq 4, version
1.0, legacy support
ohci1 at pci0 dev 18 function 1 "ATI IXP700 USB" rev 0x00: irq 4, version
1.0, legacy support
ehci0 at pci0 dev 18 function 2 "ATI IXP700 USB2" rev 0x00: irq 3
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
ohci2 at pci0 dev 19 function 0 "ATI IXP700 USB" rev 0x00: irq 10, version
1.0, legacy support
ohci3 at pci0 dev 19 function 1 "ATI IXP700 USB" rev 0x00: irq 10, version
1.0, legacy support
ehci1 at pci0 dev 19 function 2 "ATI IXP700 USB2" rev 0x00: irq 7
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "ATI EHCI root hub" rev 2.00/1.00 addr 1
piixpm0 at pci0 dev 20 function 0 "ATI IXPx00 SMBus" rev 0x3a: SMI
iic0 at piixpm0
spdmem0 at iic0 addr 0x50: 512MB DDR2 SDRAM non-parity PC2-5300CL5
pciide1 at pci0 dev 20 function 1 "ATI IXP700 IDE" rev 0x00: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
pcib0 at pci0 dev 20 function 3 "ATI IXP700 ISA" rev 0x00
ppb2 at pci0 dev 20 function 4 "ATI IXP600 PCI" rev 0x00
pci3 at ppb2 bus 3
rl0 at pci3 dev 7 function 0 "Realtek 8139" rev 0x10: irq 5, address
00:50:bf:42:36:ba
rlphy0 at rl0 phy 0: RTL internal PHY
ohci4 at pci0 dev 20 function 5 "ATI IXP700 USB" rev 0x00: irq 10, version
1.0, legacy support
pchb1 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00
pchb2 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00
kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00: core rev
DH-G2
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb4 at ohci2: USB revision 1.0
uhub4 at usb4 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb5 at ohci3: USB revision 1.0
uhub5 at usb5 "ATI OHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
it0 at isa0 port 0x2e/2: IT8718F rev 0x05, EC port 0x228
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
lms1: irq 5 already in use
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
usb6 at ohci4: USB revision 1.0
uhub6 at usb6 "ATI OHCI root hub" rev 1.00/1.00 addr 1
biomask ffdd netmask fffd ttymask ffff
mtrr: Pentium Pro MTRR support
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
