FRLinux wrote: > Hello, > > I am using 4.5 snapshots from 28022009 and using the atheros chipset > AR5413, the system just reboots when trying to set it as an access > point. On the same soekris using the AR5212 does not make the box > reboot (although I am still trying to configure it right)
could you have an under-sized power supply? Start using the thing, power consumption goes up, PS overloads and the thing reboots? I seem to recall Soekris users ran into that from time to time. Nick. > Here are the commands used: > > ifconfig ath0 192.168.5.1 255.255.255.0 media autoselect mediaopt > hostap mode 11g nwid testap nwkey testkey chan 11 > > booting hd0a:/bsd: 6039964+1059784 [52+336688+318896]=0x7657ec > entry point at 0x200120 > > [ using 656008 bytes of bsd ELF symbol table ] > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2009 OpenBSD. All rights reserved. > http://www.OpenBSD.org > > OpenBSD 4.5 (GENERIC) #1749: Sat Feb 28 14:51:18 MST 2009 > [email protected]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by > NSC" 586-class) 267 MHz > cpu0: FPU,TSC,MSR,CX8,CMOV,MMX > real mem = 268005376 (255MB) > avail mem = 250855424 (239MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 20/70/04, BIOS32 rev. 0 @ > 0xf7840 > pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000 > pcibios0: pcibios_get_intr_routing - function not supported > pcibios0: PCI IRQ Routing information unavailable. > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc8000/0x9000 > cpu0 at mainbus0: (uniprocessor) > cpu0: TSC disabled > pci0 at mainbus0 bus 0: configuration mode 1 (no bios) > pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00 > sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, > DP83816A: irq 10, address 00:00:24:c8:44:f4 > nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1 > sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, > DP83816A: irq 10, address 00:00:24:c8:44:f5 > nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1 > sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, > DP83816A: irq 10, address 00:00:24:c8:44:f6 > nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1 > ppb0 at pci0 dev 10 function 0 "TI PCI2250 PCI-PCI" rev 0x02 > pci1 at ppb0 bus 1 > sis3 at pci1 dev 0 function 0 "NS DP83815 10/100" rev 0x00, > DP83816A: irq 9, address 00:00:24:c8:31:d4 > nsphyter3 at sis3 phy 0: DP83815 10/100 PHY, rev. 1 > sis4 at pci1 dev 1 function 0 "NS DP83815 10/100" rev 0x00, > DP83816A: irq 5, address 00:00:24:c8:31:d5 > nsphyter4 at sis4 phy 0: DP83815 10/100 PHY, rev. 1 > sis5 at pci1 dev 2 function 0 "NS DP83815 10/100" rev 0x00, > DP83816A: irq 9, address 00:00:24:c8:31:d6 > nsphyter5 at sis5 phy 0: DP83815 10/100 PHY, rev. 1 > sis6 at pci1 dev 3 function 0 "NS DP83815 10/100" rev 0x00, > DP83816A: irq 5, address 00:00:24:c8:31:d7 > nsphyter6 at sis6 phy 0: DP83815 10/100 PHY, rev. 1 > ath0 at pci0 dev 14 function 0 "Atheros AR5413" rev 0x01: irq 11 > ath0: AR5413 10.5 phy 6.1 rf 6.3, FCC2A*, address > 00:0b:6b:2f:02:1e > gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00 > gpio0 at gscpcib0: 64 pins > "NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured > pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, > channel 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX4-4096> > wd0: 4-sector PIO, LBA, 3919MB, 8027712 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid > 6 revision 3 wdstatus 0 > ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: > irq 5, version 1.0, legacy support > isa0 at gscpcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > com0: console > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS > gpio1 at nsclpcsio0: 29 pins > gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1: > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > usb0 at ohci0: USB revision 1.0 > uhub0 at usb0 "Compaq OHCI root hub" rev 1.00/1.00 addr 1 > biomask f1e5 netmask ffe5 ttymask ffff > softraid0 at root > root on wd0a swap on wd0b dump on wd0b > Automatic boot in progress: starting file system checks. > /dev/rwd0a: file system is clean; not checking > /dev/rwd0d: file system is clean; not checking > setting tty flags > kbd: keyboard mapping set to fr > pf enabled > net.inet.ip.forwarding: 0 -> 1 > net.inet6.ip6.forwarding: 0 -> 1 > **reboot** > > Cheers, > Steph
