On Jan 31, 2008 5:02 AM, Andre Naehring <[EMAIL PROTECTED]> wrote:
> On Wed, 30 Jan 2008, Stuart Henderson wrote:
>
> > On 2008/01/30 15:26, Dennis Davis wrote:
> >>
> >> "wireless driver reports an error and does not work" is short on
> >> detail. It might just be that non-free firmware needs installing
> >> (eg the firmware for the iwi driver) to get it to work.
> >
> > people with Eee PC need to test -current snapshots, the wd/wdc
> > changes which are in them (not yet committed) will affect you
> > (hopefully to your advantage, there should be much lower cpu
> > use during disk activity).
>
> So, installed current from Jan 28 on an usb stick and booted. Ethernet
> works fine on the eee, but the wireless always reports
>
> ath0: unable to reset hardware; hal status 4096
>
> when I want to set something.
>
> according to the manpage, this should not happen.
>
> dmesg follows...
>
> OpenBSD 4.2-current (GENERIC) #652: Mon Jan 28 14:04:36 MST 2008
> [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: Intel(R) Celeron(R) M processor 900MHz ("GenuineIntel"
> 686-class) 631 MHz
> cpu0:
>
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF
> real mem = 527527936 (503MB)
> avail mem = 502153216 (478MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 01/04/08, BIOS32 rev. 0 @
> 0xf0010, SMBIOS rev. 2.5 @ 0xf06c0 (37 entries)
> bios0: vendor American Megatrends Inc. version "0703" date
> 01/04/2008
> bios0: ASUSTeK Computer INC. 701
> apm0 at bios0: Power Management spec V1.2
> apm0: AC on, battery charge unknown
> acpi at bios0 function 0x0 not configured
> pcibios0 at bios0: rev 3.0 @ 0xf0000/0x10000
> pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf76b0/176 (9 entries)
> pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801FB LPC" rev
> 0x00)
> pcibios0: PCI bus #5 is the last bus
> bios0: ROM list: 0xc0000/0xf800!
> cpu0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "Intel 82915GM Host" rev 0x04
> agp0 at pchb0: aperture at 0xd0000000, size 0x10000000
> vga1 at pci0 dev 2 function 0 "Intel 82915GM Video" rev 0x04
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> "Intel 82915GM Video" rev 0x04 at pci0 dev 2 function 1 not
> configured
> azalia0 at pci0 dev 27 function 0 "Intel 82801FB HD Audio" rev 0x04:
> irq 5
> azalia0: codec[s]: Realtek/0x0662
> audio0 at azalia0
> ppb0 at pci0 dev 28 function 0 "Intel 82801FB PCIE" rev 0x04: irq 5
> pci1 at ppb0 bus 4
> ppb1 at pci0 dev 28 function 1 "Intel 82801FB PCIE" rev 0x04: irq 11
> pci2 at ppb1 bus 3
> lii0 at pci2 dev 0 function 0 "Attansic Technology L2" rev 0xa0: irq
> 11, address 00:1e:8c:b9:38:d8
> ukphy0 at lii0 phy 1: Generic IEEE 802.3u media interface, rev. 2:
> OUI 0x001374, model 0x0002
> ppb2 at pci0 dev 28 function 2 "Intel 82801FB PCIE" rev 0x04: irq 10
> pci3 at ppb2 bus 1
> ath0 at pci3 dev 0 function 0 "Atheros AR5424" rev 0x01: irq 10
> ath0: AR5424 14.2 phy 7.0 rf 0.0, WOR0W, address 00:15:af:75:d9:e0
> uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x04: irq 3
> uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x04: irq 7
> uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x04: irq 10
> uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x04: irq 5
> ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x04: irq 3
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
> ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd4
> pci4 at ppb3 bus 5
> ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x04: PM
> disabled
> pciide0 at pci0 dev 31 function 2 "Intel 82801FBM SATA" rev 0x04:
> DMA, channel 0 wired to compatibility, channel 1 wired to
> compatibility
> wd0 at pciide0 channel 1 drive 0: <SILICONMOTION SM223AC>
> wd0: 1-sector PIO, LBA, 3815MB, 7815024 sectors
> wd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 4
> ichiic0 at pci0 dev 31 function 3 "Intel 82801FB SMBus" rev 0x04:
> irq 7
> iic0 at ichiic0
> spdmem0 at iic0 addr 0x50: 512MB DDR2 SDRAM non-parity PC2-5300CL5
> SO-DIMM
> usb1 at uhci0: USB revision 1.0
> uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb2 at uhci1: USB revision 1.0
> uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb3 at uhci2: USB revision 1.0
> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb4 at uhci3: USB revision 1.0
> uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> isa0 at ichpcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pms0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pms0 mux 0
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> biomask e7fd netmask effd ttymask ffff
> mtrr: Pentium Pro MTRR support
> umass0 at uhub0 port 3 configuration 1 interface 0 "USBest
> Technology USB Mass Storage Device" rev 2.00/1.00 addr 2
> umass0: using SCSI over Bulk-Only
> scsibus0 at umass0: 2 targets
> sd0 at scsibus0 targ 1 lun 0: <Ut163, USB2FlashStorage, 0.00> SCSI2
> 0/direct removable
> sd0: 963MB, 122 cyl, 255 head, 63 sec, 512 bytes/sec, 1974271 sec
> total
> umass1 at uhub0 port 5 configuration 1 interface 0 "ENE UB6225" rev
> 2.00/1.00 addr 3
> umass1: using SCSI over Bulk-Only
> scsibus1 at umass1: 2 targets
> sd1 at scsibus1 targ 1 lun 0: <USB2.0, CardReader SD0, 0100> SCSI0
> 0/direct removable
> sd1: drive offline
> softraid0 at root
> root on sd0a swap on sd0b dump on sd0b
>
Did you have to do boot> boot -a to get it to boot properly off of sd0a,
recompile kernel or something else?
When I try, I never get it to see "root on sd0a swap on sd0b dump on sd0b"
by itself, at least without boot -a or a kernel recompile...
By chance, have you tried the same with non -current - just wondering if it
boots and detects ok with root on sd0a?
Thanks!
