Hi all,
In hostap mode, machine freezes after pulling card out.
Keyboard still reacts in Caps or NumLock but terminal
does not accept any input; the following gets repeated:
wi0: wi_mgnt_xmit: xmit failed
wi0: init failed
Besides that, card works well (tested only hostap mode).
Also, there is no diff if card gets inserted before boot or
into running system - JustWorks(TM):
How to enable WIDEBUG in if_wi.c (or where else?) ?
Simply placing #define WIDEBUG resulted in compile errs.
wi0 at pcmcia0 function 0 " , IEEE 802.11 Wireless LAN/PC Card, " port 0xc000/64
wi0: PRISM2 HWB3163 rev.A (0x8002), Firmware 0.3.0 (primary), 0.8.3
(station), address 00:60:b3:6f:73:e2
inet 192.168.1.1 255.255.255.0 NONE media autoselect \
mediaopt hostap nwid my_net2 chan 11
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33208
groups: lo
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
rl0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:00:e2:56:a4:34
media: Ethernet autoselect
status: no carrier
rl1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:0a:79:05:fe:1b
media: Ethernet autoselect
status: no carrier
enc0: flags=0<> mtu 1536
wi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:60:b3:6f:73:e2
media: IEEE802.11 autoselect hostap (DS2)
status: active
ieee80211: nwid my_net2 chan 11 bssid 00:60:b3:6f:73:e2 8dBm (auto)
inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
inet6 fe80::260:b3ff:fe6f:73e2%wi0 prefixlen 64 scopeid 0x5
OpenBSD 4.1-current (GENERIC) #332: Sat Jul 21 14:17:12 MDT 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Duron(tm) processor ("AuthenticAMD" 686-class, 64KB L2 cache) 901 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem = 116944896 (111MB)
avail mem = 105193472 (100MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 10/22/01, BIOS32 rev. 0 @
0xfa9b0, SMBIOS rev. 2.3 @ 0xf0000 (46 entries)
bios0: FUJITSU FMVCE8905
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdf94
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf00/144 (7 entries)
pcibios0: PCI Exclusive IRQs: 7 10 11
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C596A ISA" rev 0x00)
pcibios0: PCI bus #3 is the last bus
bios0: ROM list: 0xc0000/0xc000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT8363 Host" rev 0x81
ppb0 at pci0 dev 1 function 0 "VIA VT8363 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "S3 ProSavage KM133" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C686 ISA" rev 0x22
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x10: ATA66,
channel 0 configured to compatibility, channel 1 configured to
compatibility
wd0 at pciide0 channel 0 drive 0: <FUJITSU MPC3064AT>
wd0: 16-sector PIO, LBA, 6187MB, 12672450 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
uhci0 at pci0 dev 7 function 2 "VIA VT83C572 USB" rev 0x10: irq 10
uhci1 at pci0 dev 7 function 3 "VIA VT83C572 USB" rev 0x10: irq 10
viaenv0 at pci0 dev 7 function 4 "VIA VT82C686 SMBus" rev 0x30: HWM
disabled: 24-bit timer at 3579545Hz
auvia0 at pci0 dev 7 function 5 "VIA VT82C686 AC97" rev 0x20: irq 11
ac97: codec id 0x594d4800 (Yamaha YMF743-S)
ac97: codec features 18 bit DAC, No 3D Stereo
audio0 at auvia0
"VIA VT82C686 Modem" rev 0x20 at pci0 dev 7 function 6 not configured
"AT&T/Lucent FW322 1394" rev 0x04 at pci0 dev 11 function 0 not configured
rl0 at pci0 dev 12 function 0 "Realtek 8139" rev 0x10: irq 10, address
00:00:e2:56:a4:34
rlphy0 at rl0 phy 0: RTL internal PHY
cbb0 at pci0 dev 14 function 0 "Ricoh 5C476 CardBus" rev 0x80: irq 11
cbb1 at pci0 dev 14 function 1 "Ricoh 5C476 CardBus" rev 0x80: irq 10
rl1 at pci0 dev 16 function 0 "Realtek 8139" rev 0x10: irq 11, address
00:0a:79:05:fe:1b
rlphy1 at rl1 phy 0: RTL internal PHY
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
usb0 at uhci0: USB revision 1.0
uhub0 at usb0: VIA UHCI root hub, rev 1.00/1.00, addr 1
usb1 at uhci1: USB revision 1.0
uhub1 at usb1: VIA UHCI root hub, rev 1.00/1.00, addr 1
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0 cacheline 0x0, lattimer 0x20
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 3 device 0 cacheline 0x0, lattimer 0x20
pcmcia1 at cardslot1
biomask fffd netmask fffd ttymask ffff
pctr: user-level cycle counter enabled
mtrr: Pentium Pro MTRR support
wi0 at pcmcia0 function 0 " , IEEE 802.11 Wireless LAN/PC Card, " port 0xc000/64
wi0: PRISM2 HWB3163 rev.A (0x8002), Firmware 0.3.0 (primary), 0.8.3
(station), address 00:60:b3:6f:73:e2
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a swap on wd0b dump on wd0b
vladas
