Hi,
I got some troubles. My openbsd hasn't any usb support, i tried to moun and
usb pen drive, or configure my usb printer with no good results.
I'm using downloaded openbsd from the ftp ( using cd40.iso to boot and get
the install program then download the rest trough ftp ), and Jon Drews
suggested me to get orginal CD , i will wait til 4.1 ( thanks Jon for all ).
Here is the output for dmesg:
OpenBSD 4.0 (GENERIC) #1107: Sat Sep 16 19:15:58 MDT 2006
[EMAIL PROTECTED] :/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class, 512KB L2 cache) 502 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem = 268005376 (261724K)
avail mem = 236724224 (231176K)
using 3297 buffers containing 13504512 bytes (13188K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(53) BIOS, date 03/10/00, BIOS32 rev. 0 @ 0xfb120,
SMBIOS rev. 2.3 @ 0xf0800 (33 entries)
bios0: VIA Technologies, Inc. VT82C693ABX
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb59c
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdbd0/128 (6 entries)
pcibios0: PCI Exclusive IRQs: 11
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C596A ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT82C691 PCI" rev 0x44
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "S3 Trio3 DX2" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C596A ISA" rev 0x23
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x10: ATA66, channel
0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <ST38410A>
wd0: 32-sector PIO, LBA, 8223MB, 16841664 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, CD-ROM GCR-8520B, 1.00> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
"VIA VT82C596 Power" rev 0x30 at pci0 dev 7 function 3 not configured
rl0 at pci0 dev 11 function 0 "Realtek 8139" rev 0x10: irq 11, address
00:48:54:6a:75:30
rlphy0 at rl0 phy 0: RTL internal PHY
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask f765 netmask ff65 ttymask ffe7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
lpt0: out of paper
lpt0: stat=0x4 not zero
lpt0: stat=0x4 not zero
I get this with usb printer connected and the pen drive. I'm using a P3
board.
Any help?
Thanks for all,
Tang
