I have an HP nx6125 laptop, and I just got the HP Advanced Dock Station
so I could use serial console for debugging. If I connect to serial
it works until the kernel prints out com0:
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fif
(yes, it stops at 'fif')
The boot process does continue, but the console stops updating. if I
send disconnect signals, it prints '[EOT]' and stays connected. After
60-90 minutes it actually disconnects.
if I connect serial after boot is finished, I get the standard login
prompt, I can login and do stuff. If I kick off a reboot, it it gets
as far as the "Rebooting..." message, then nothing.
--
Coincidence, n.:
You weren't paying attention to the other half of what was
going on.
OpenBSD 4.0-current (GENERIC) #738: Sun Nov 5 14:12:38 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/amd64/compile/GENERIC
real mem = 2012672000 (1965500K)
avail mem = 1718460416 (1678184K)
using 22937 buffers containing 201474048 bytes (196752K) of memory
mainbus0 (root)
bios0 at mainbus0: SMBIOS rev. 2.3 @ 0xfc68f (23 entries)
bios0: Hewlett-Packard HP Compaq nx6125 (PZ895UA#ABA)
cpu0 at mainbus0: (uniprocessor)
cpu0: AMD Turion(tm) 64 Mobile ML-37 , 1995.35 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,SSE3,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 1MB 64b/line
16-way L2 cache
cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: PowerNow! K8 1995 MHz: speeds: 2000 1800 1600 800 MHz
pci0 at mainbus0 bus 0: configuration mode 1
pchb0 at pci0 dev 0 function 0 "ATI RS480 Host" rev 0x01
ppb0 at pci0 dev 1 function 0 "ATI RS480 PCIE" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon XPRESS 200M" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb1 at pci0 dev 4 function 0 "ATI RS480 PCIE" rev 0x00
pci2 at ppb1 bus 16
ppb2 at pci0 dev 5 function 0 "ATI RS480 PCIE" rev 0x00
pci3 at ppb2 bus 32
ohci0 at pci0 dev 19 function 0 "ATI IXP400 USB" rev 0x00: irq 10, version 1.0,
legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: ATI OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ohci1 at pci0 dev 19 function 1 "ATI IXP400 USB" rev 0x00: irq 10, version 1.0,
legacy support
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: ATI OHCI root hub, rev 1.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
ehci0 at pci0 dev 19 function 2 "ATI IXP400 USB2" rev 0x00: irq 10
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: ATI EHCI root hub, rev 2.00/1.00, addr 1
uhub2: 8 ports with 8 removable, self powered
piixpm0 at pci0 dev 20 function 0 "ATI IXP400 SMBus" rev 0x11: SMI
iic0 at piixpm0
admtemp0 at iic0 addr 0x4c: adm1032
pciide0 at pci0 dev 20 function 1 "ATI IXP400 IDE" rev 0x00: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <FUJITSU MHV2060AH>
wd0: 16-sector PIO, LBA, 57231MB, 117210240 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <MATSHITA, UJ-840D, 1.02> SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
pcib0 at pci0 dev 20 function 3 "ATI IXP400 ISA" rev 0x00
ppb3 at pci0 dev 20 function 4 "ATI IXP400 PCI" rev 0x00
pci4 at ppb3 bus 2
bge0 at pci4 dev 1 function 0 "Broadcom BCM5788" rev 0x03, BCM5705 A3 (0x3003):
irq 10, address 00:0f:b0:f6:46:19
brgphy0 at bge0 phy 1: BCM5705 10/100/1000baseT PHY, rev. 2
"Broadcom BCM4319" rev 0x02 at pci4 dev 2 function 0 not configured
cbb0 at pci4 dev 4 function 0 "TI PCI7XX1 CardBus" rev 0x00: irq 11
"TI PCI7XX1 FireWire" rev 0x00 at pci4 dev 4 function 2 not configured
"TI PCI7XX1 Flash" rev 0x00 at pci4 dev 4 function 3 not configured
sdhc0 at pci4 dev 4 function 4 "TI PCI7XX1 Secure Data" rev 0x00: irq 9
sdmmc0 at sdhc0
sdmmc1 at sdhc0
sdmmc2 at sdhc0
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3 device 0 cacheline 0x10, lattimer 0x20
pcmcia0 at cardslot0
auixp0 at pci0 dev 20 function 5 "ATI IXP400 AC97" rev 0x02: irq 5
auixp0: soft resetting aclink
"ATI IXP400 Modem" rev 0x02 at pci0 dev 20 function 6 not configured
pchb1 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00
pchb2 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00
pchb4 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
uhub3 at uhub2 port 1
uhub3: Cypress Semiconductor USB2 Hub, rev 2.00/0.0b, addr 2
uhub3: 4 ports with 4 removable, self powered, multiple transaction translators
uhub4 at uhub2 port 4
uhub4: Cypress Semiconductor USB2 Hub, rev 2.00/0.0b, addr 3
uhub4: 4 ports with 4 removable, self powered, multiple transaction translators
ugen0 at uhub1 port 1
ugen0: AuthenTec Fingerprint Sensor, rev 1.10/6.21, addr 2
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
ac97: codec id 0x43585430 (Conexant CX?????)
ac97: codec features reserved, headphone, 18 bit DAC, 18 bit ADC, No 3D Stereo
audio0 at auixp0
