Here is the whole initialization output.
boot>
booting fd0a:/bsd: 4435508+740284=0x4efb38
entry point at 0x100120
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2006 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 3.9 (RAMDISK_CD) #1025: Thu Mar 2 02:43:29 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 930 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem = 2281267200 (2227800K)
avail mem = 2072780800 (2024200K)
using 4278 buffers containing 114167808 bytes (111492K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 12/31/99, BIOS32 rev. 0 @ 0xf0000
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x2000
pcibios0: PCI BIOS has 9 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:15:0 ("ServerWorks OSB4" rev 0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x4000 0xcc000/0x1800 0xe8000/0x6000
0xee000/0x2000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20LE Host" rev 0x06
pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20LE Host" rev 0x06
pci1 at pchb1 bus 2
ppb0 at pci1 dev 5 function 0 "IBM 82351 PCI-PCI" rev 0x07
pci2 at ppb0 bus 3
cac0 at pci2 dev 0 function 0 "Compaq SMART2P RAID" rev 0x04: irq 10 Compaq
Smart Array 3200
scsibus0 at cac0: 1 targets
sd0 at scsibus0 targ 0 lun 0: <Compaq, RAID5 volume #, > SCSI2 0/direct
fixed
sd0: 191014MB, 191014 cyl, 64 head, 32 sec, 512 bytes/sec, 391198560 sec
total
"Compaq Netelligent ASMC" rev 0x00 at pci0 dev 3 function 0 not configured
vga1 at pci0 dev 5 function 0 "ATI Mach64 GV" rev 0x7a
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 15 function 0 "ServerWorks OSB4" rev 0x4f
pciide0 at pci0 dev 15 function 1 "ServerWorks OSB4 IDE" rev 0x00: DMA
atapiscsi0 at pciide0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <COMPAQ, SC-140S, SE04> SCSI0 5/cdrom
removable
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pchb2 at pci0 dev 17 function 0 "ServerWorks CNB20LE Host" rev 0x06
pchb3 at pci0 dev 17 function 1 "ServerWorks CNB20LE Host" rev 0x06
pci3 at pchb3 bus 5
siop0 at pci3 dev 4 function 0 "Symbios Logic 53c896" rev 0x07: irq 11,
using 8K of on-board RAM
scsibus2 at siop0: 16 targets
siop0: target 1 now using 8 bit async xfers
siop0: target 1 now using 8 bit 40.0 MHz 31 REQ/ACK offset xfers
sd1 at scsibus2 targ 1 lun 0: <IBM-PSG, ST318436LW !#, 3281> SCSI3 0/direct
fixed
sd1: 17357MB, 14384 cyl, 6 head, 411 sec, 512 bytes/sec, 35548320 sec total
st0 at scsibus2 targ 6 lun 0: <COMPAQ, SDT-10000, 1.09> SCSI2 1/sequential
removable
st0: drive empty or not ready
siop1 at pci3 dev 4 function 1 "Symbios Logic 53c896" rev 0x07: couldn't
establish interrupt at irq 15
extent_free: start 0xf7ffbc00, end 0xf7ffbcff
panic: extent_free: region not found
cac0: timeout
The operating system has halted.
Please press any key to reboot.
[ ]'s Beto
On 8/12/06, Kenneth R Westerback <[EMAIL PROTECTED]> wrote:
>
> On Sat, Aug 12, 2006 at 07:24:19PM -0300, Beto wrote:
> > Hi Folks,
> > I'm trying to install OpenBSD 3.9 on a Compaq Proliant ML 530 but It
> just
> > doesn't work. When the cd install kernel are reconizing the devices it
> shows
> > a panic error and prints a halt message. I also tryed install OpenBSD
> > 3.8and the same error.
> > The machine comes with a Smart Start CD I use to configure the BIOS to
> > indicate the Operating Sytem that will be installed and there are a lot
> of
> > options for UNIX install but noone for OpenBSD or even for BSD's OS. I
> just
> > try all the options and the error persist.
> > When I installed FreeBSD the installation was finished suscceffully.
> > Ok, let me show the options and the errors.
> >
> > Primary Operating System:
> > Banyan VINES
> > DOS
> > NetWare
> > OS/2
> > UNIX -> OpenServer 5
> > Solaris
> > UnixWare 7
> > UnixWare 2.1
> > UNIX (large drive geometry) ** I've installed FreeBSD,
> > works
> > UNIX (small drive geometry) ** I've installed FreeBSD,
> works
> > Linux ** I've installed Debian, works.
> > Windows NT
> > Other
> >
> > Ok. the errors are:
> >
> > siop1 at pci3 dev 4 function 1 "Symbios Logic 53c896" rev 0x07: coudn't
> > establish interrupt at irq 15
> > extent_free: start 0xf7ffbc00, end 0xf7ffbcff
> > panic: extent_free: region not found
> > cac0: timeout
> >
> > The operating system has halted.
> > Please press any key to reboot.
> >
> >
> > That is it. I will apreciate any help.
> > Thank you
> > [ ]'s Beto
> >
>
> Try a snapshot. That sounds familiar and fixed to me.
>
> .... Ken
