I have a box, happily running OpenBSD 3.8-stable. I'm trying to
move it to 3.9. I downloaded bsd.rd to /, and rebooted the box.
I typed boot bsd.rd and the box boots, to a point. This box has
an Adaptec 2940UW Pro. The boot sort of hangs when it reaches
the initialization for this device. It prints:
ahc0 at pci0 dev 10 function 0 "Adaptec AHA-2940UWPro" rev 0x01: irq 11
scsibus0 at ahc0: 16 targets
ahc0: board is not responding
ahc0: board is not responding
ahc0: board is not responding
And then continues on with the boot. When I try to install, no disk is
found and therefore, I can't install.
I've tried, bsd.rd, floppy39.fs and floppyb39.fs. bsd.rd and floppy39.fs
react identically. Floppyb39.fs doesn't have a driver for ahc, but I
thought it might be worth a try. I don't have a CD drive in this machine.
I notice in the 3.8 machine, the controller is recognized as ahc1 while
3.9 recognizes it as ahc0 and it doesn't work. Is there something that I
need to change on my end, or is this just a change in the way the driver
numbers the controllers?
Also, for what it's worth, bsd.rd from 3.9-current does the same thing as
the bsd.rd from 3.9.
For reference I've included the 3.8-stable dmesg, as I don't have
serial console set up on this box to capture the 3.9-bsd.rd dmesg.
Suggestions welcome.
Thanks,
Rodney Hopkins
[EMAIL PROTECTED]
OpenBSD 3.8-stable (GENERIC) #6: Sun Mar 19 19:45:58 CST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 1.01 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,SER,MMX,FXSR,SSE
real mem = 536453120 (523880K)
avail mem = 482594816 (471284K)
using 4278 buffers containing 26927104 bytes (26296K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 09/14/01, BIOS32 rev. 0 @ 0xfdb50
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf7d50/128 (6 entries)
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C686 ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x5800 0xcd800/0x800 0xce000/0x2000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT82C691 PCI" rev 0xc4
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 AGP" rev 0x00
pci1 at ppb0 bus 1
pcib0 at pci0 dev 7 function 0 "VIA VT82C686 ISA" rev 0x40
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x06: ATA100, channel 0
configured to compatibility, channel 1 configured to compatibility
pciide0: channel 0 disabled (no drives)
pciide0: channel 1 disabled (no drives)
viaenv0 at pci0 dev 7 function 4 "VIA VT82C686 SMBus" rev 0x40
vga1 at pci0 dev 9 function 0 "S3 86C968-0" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ahc1 at pci0 dev 10 function 0 "Adaptec AHA-2940UWPro" rev 0x01: irq 11
scsibus0 at ahc1: 16 targets
ahc1: target 0 using 8bit transfers
ahc1: target 0 using asynchronous transfers
sd0 at scsibus0 targ 0 lun 0: <IBM, DCHS09Y, 6464> SCSI2 0/direct fixed
sd0: 8678MB, 6082 cyl, 18 head, 162 sec, 512 bytes/sec, 17774160 sec total
xl0 at pci0 dev 12 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 12,
address 00:01:03:df:0a:5f
bmtphy0 at xl0 phy 24: Broadcom 3C905C internal PHY, rev. 7
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask ef65 netmask ff65 ttymask ffe7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
ahc1: target 0 using 16bit transfers
ahc1: target 0 synchronous at 20.0MHz, offset = 0x8
dkcsum: sd0 matches BIOS drive 0x80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
_____________________________________________________________
Free E-mail by CamaroZ28.Com - FULL THROTTLE INTERNET
