After install/upgrade OpenBSD 3.9 at the system startup the operating system jams with this error: "fxp0: SCB time out". The error is occured when the system tried to assign the IP at the network card. Now I have disabled the network startup.
The dmesg reports: =================== OpenBSD 3.9 (GENERIC) #617: Thu Mar 2 02:26:48 MST 2006 [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel(R) Pentium(R) M processor 1.73GHz ("GenuineIntel" 686-class) 1.73 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,T M,SBF,EST,TM2 cpu0: Enhanced SpeedStep 1300 MHz (1308 mV): unknown EST cpu, no changes possible real mem = 535273472 (522728K) avail mem = 481411072 (470128K) using 4278 buffers containing 26865664 bytes (26236K) of memory mainbus0 (root) bios0 at mainbus0: AT/286+(8c) BIOS, date 01/16/05, BIOS32 rev. 0 @ 0xfd6b0 apm0 at bios0: Power Management spec V1.2 apm0: AC on, battery charge unknown apm0: flags 30102 dobusy 0 doidle 1 pcibios0 at bios0: rev 2.1 @ 0xfd6b0/0x950 pcibios0: PCI BIOS has 16 Interrupt Routing table entries pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801FBM LPC" rev 0x00) pcibios0: PCI bus #3 is the last bus bios0: ROM list: 0xc0000/0xec00! 0xdc000/0x4000! 0xe0000/0x4000! cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 "Intel 82915GM/PM/GMS Host" rev 0x03 ppb0 at pci0 dev 1 function 0 "Intel 82915PM/GM PCIE" rev 0x03 pci1 at ppb0 bus 1 vga1 at pci1 dev 0 function 0 vendor "NVIDIA", unknown product 0x0167 rev 0xa1 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) "Intel 82801FB HD Audio" rev 0x04 at pci0 dev 27 function 0 not configured uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x04: irq 5 usb0 at uhci0: USB revision 1.0 uhub0 at usb0 uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x04: irq 10 usb1 at uhci1: USB revision 1.0 uhub1 at usb1 uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x04: irq 3 usb2 at uhci2: USB revision 1.0 uhub2 at usb2 uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x04: irq 11 usb3 at uhci3: USB revision 1.0 uhub3 at usb3 uhub3: Intel UHCI root hub, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x04: irq 5 usb4 at ehci0: USB revision 2.0 uhub4 at usb4 uhub4: Intel EHCI root hub, rev 2.00/1.00, addr 1 uhub4: 8 ports with 8 removable, self powered ppb1 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd4 pci2 at ppb1 bus 2 cbb0 at pci2 dev 3 function 0 "Texas Instruments PCI7420 CardBus" rev 0x00pci_intr_map: no mapping for pin A : couldn't map interrupt "Texas Instruments PCI7x20 FireWire" rev 0x00 at pci2 dev 3 function 2 not configured vendor "Texas Instruments", unknown product 0xac8f (class mass storage subclass miscellaneous, rev 0x00) at pci2 dev 3 function 3 not configured iwi0 at pci2 dev 4 function 0 "Intel PRO/Wireless 2200BG" rev 0x05: irq 4, address 00:0e:35:d5:d6:ea fxp0 at pci2 dev 8 function 0 "Intel 82801FBM LAN" rev 0x04, i82562: irq 7, address 00:01:4a:17:e2:f4 inphy0 at fxp0 phy 1: i82562ET 10/100 PHY, rev. 0 ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x04: PM disabled pciide0 at pci0 dev 31 function 1 "Intel 82801FB IDE" rev 0x04: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility wd0 at pciide0 channel 0 drive 0: <HITACHI_DK23FA-80> wd0: 16-sector PIO, LBA, 76319MB, 156301488 sectors atapiscsi0 at pciide0 channel 0 drive 1 scsibus0 at atapiscsi0: 2 targets cd0 at scsibus0 targ 0 lun 0: <MAT****A, UJ-831Da, 1.01> SCSI0 5/cdrom removable wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2 pciide0: channel 1 ignored (disabled) ichiic0 at pci0 dev 31 function 3 "Intel 82801FB SMBus" rev 0x04: irq 10 iic0 at ichiic0 isa0 at ichpcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pms0 mux 0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: <PC speaker> spkr0 at pcppi0 npx0 at isa0 port 0xf0/16: using exception 16 biomask ef6d netmask effd ttymask ffff pctr: 686-class user-level performance counters enabled mtrr: Pentium Pro MTRR support umass0 at uhub4 port 3 configuration 1 interface 0 umass0: Verbatim Store 'n' Go, rev 2.00/1.00, addr 2 umass0: using SCSI over Bulk-Only scsibus1 at umass0: 2 targets sd0 at scsibus1 targ 1 lun 0: <VBTM, Store 'n' Go, 1.04> SCSI0 0/direct removable sd0: 489MB, 489 cyl, 64 head, 32 sec, 512 bytes/sec, 1001472 sec total uhidev0 at uhub0 port 1 configuration 1 interface 0 uhidev0: Logitech USB-PS/2 Optical Mouse, rev 2.00/18.00, addr 2, iclass 3/1 ums0 at uhidev0: 6 buttons and Z dir. wsmouse1 at ums0 mux 0 dkcsum: wd0 matches BIOS drive 0x80 root on wd0a rootdev=0x0 rrootdev=0x300 rawdev=0x302 WARNING: / was not properly unmounted
