Hi,
I have found that my Mango Pi is very jittery, also when I reboot it there
is probably garble on the UART link causing it to fall into u-boot prompt.
I have tried:
env set bootdelay 0
env set bootdelay -1
saveenv
and reset
but it doesn't seem to work. Any garble will still cause a break to u-boot
console. There is a firmware image on the flash and in DTB under config
but how do I access that from OpenBSD? Is there any drivers I can look at
for making this work? I believe it goes on the "binman" device that is not
configured.
deneb# dmesg|grep binman
"binman" at mainbus0 not configured
Granted that there isn't an easy answer, I'll look at this perhaps in autumn.
Here is my dmesg:
OpenBSD 7.5-current (GENERIC) #5: Mon Apr 8 08:27:57 MDT 2024
[email protected]:/usr/src/sys/arch/riscv64/compile/GENERIC
real mem = 1073741824 (1024MB)
avail mem = 1008369664 (961MB)
SBI: OpenSBI v1.3, SBI Specification Version 1.0
random: good seed from bootblocks
mainbus0 at root: MangoPi MQ Pro
cpu0 at mainbus0: T-Head arch 0 imp 0 rv64imafdc
intc0 at cpu0
cpu0: 32KB 64b/line 128-way L1 I-cache, 32KB 64b/line 256-way L1 D-cache
"fit-images" at mainbus0 not configured
"dcxo-clk" at mainbus0 not configured
simplebus0 at mainbus0: "soc"
sxipio0 at simplebus0: 88 pins
sxiccmu0 at simplebus0
plic0 at simplebus0
sxitimer0 at simplebus0: 24000 kHz
sxidog0 at simplebus0
com0 at simplebus0: dw16550
com0: console
com1 at simplebus0: dw16550
"syscon" at simplebus0 not configured
"dma-controller" at simplebus0 not configured
"efuse" at simplebus0 not configured
"crypto" at simplebus0 not configured
"dram-controller" at simplebus0 not configured
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
sximmc1 at simplebus0
sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
"usb" at simplebus0 not configured
"phy" at simplebus0 not configured
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
ohci0 at simplebus0: version 1.0
"clock-controller" at simplebus0 not configured
"mixer" at simplebus0 not configured
"mixer" at simplebus0 not configured
"phy" at simplebus0 not configured
"tcon-top" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
"power-controller" at simplebus0 not configured
"clock-controller" at simplebus0 not configured
sxirtc0 at simplebus0
sxidog1 at simplebus0
sxidog2 at simplebus0
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00
addr 1
"opp-table-cpu" at mainbus0 not configured
"pmu" at mainbus0 not configured
"vcc" at mainbus0 not configured
"vcc-3v3" at mainbus0 not configured
"leds" at mainbus0 not configured
"avdd2v8" at mainbus0 not configured
"dvdd" at mainbus0 not configured
"vdd-cpu" at mainbus0 not configured
"wifi-pwrseq" at mainbus0 not configured
"binman" at mainbus0 not configured
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Sandisk, SN128, 0080> removable
sd0: 121942MB, 512 bytes/sector, 249737216 sectors
manufacturer 0x024c, product 0xd723 at sdmmc1 function 1 not configured
uhub2 at uhub0 port 1 configuration 1 interface 0 "vendor 0x1a40 USB 2.0 Hub"
rev 2.00/1.11 addr 2
ure0 at uhub2 port 4 configuration 1 interface 0 "Realtek USB 10/100 LAN" rev
2.10/20.00 addr 3
ure0: RTL8152 (0x4c10), address 00:e0:4c:36:00:e9
rlphy0 at ure0 phy 0: RTL8201E 10/100 PHY, rev. 2
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on sd0a (ff09abc802626de6.a) swap on sd0b dump on sd0b
sxiccmu_d1_set_frequency: 0x00000084
cpu0: clock not implemented
Best Regards,
-pjp
--
my associated domains: callpeter.tel|centroid.eu|dtschland.eu|mainrechner.de
