Hello List,
So I'm using a Loongson YeeLoong netbook. I installed XFCE4 without any
issues, But it will freeze after around 15 minutes, even if I do nothing on
it. Starting "terminal" will cause it to freeze immediately.
I can still SSH into this netbook after freeze and everything else seems to
be fine.
This happens back during 4.9 days. It's the same on 5.0 and current
snapshot.
Any insight will be appreciated. and I'll be glad to provide any info
required to troubleshoot this.
I'm not sure exactly what info will be needed, so I'll start with dmesg.
More will be provided as necessary:
[ using 466480 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2012 OpenBSD. All rights reserved.
http://www.OpenBSD.org <http://www.openbsd.org/>
OpenBSD 5.1 (GENERIC) #93: Sun Feb 12 18:10:05 MST 2012
[email protected]:/usr/src/sys/arch/loongson/compile/GENERIC
real mem = 1073741824 (1024MB)
avail mem = 1059160064 (1010MB)
mainbus0 at root: Lemote Yeeloong
cpu0 at mainbus0: STC Loongson2F CPU 796 MHz, STC Loongson2F FPU
cpu0: cache L1-I 64KB D 64KB 4 way, L2 512KB 4 way
bonito0 at mainbus0: memory and PCI-X controller, rev 1
pci0 at bonito0 bus 0
rl0 at pci0 dev 7 function 0 "Realtek 8139" rev 0x10: irq 5, address
00:23:8b:b5:38:eb
rlphy0 at rl0 phy 0: RTL internal PHY
smfb0 at pci0 dev 8 function 0 "Silicon Motion LynxEM+" rev 0xb0
wsdisplay0 at smfb0 mux 1: console (std, vt100 emulation)
ohci0 at pci0 dev 9 function 0 "NEC USB" rev 0x44: irq 7, version 1.0
ehci0 at pci0 dev 9 function 1 "NEC USB" rev 0x05: irq 7
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "NEC EHCI root hub" rev 2.00/1.00 addr 1
glxpcib0 at pci0 dev 14 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio
gpio1 at glxpcib0: 32 pins
pciide0 at pci0 dev 14 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <ST9160310AS>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
auglx0 at pci0 dev 14 function 3 "AMD CS5536 Audio" rev 0x01: isa irq 9,
CS5536 AC97
ac97: codec id 0x414c4760 (Avance Logic ALC655 rev 0)
audio0 at auglx0
ohci1 at pci0 dev 14 function 4 "AMD CS5536 USB" rev 0x02: isa irq 11,
version 1.0, legacy support
ehci1 at pci0 dev 14 function 5 "AMD CS5536 USB" rev 0x02: isa irq 11
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "AMD EHCI root hub" rev 2.00/1.00 addr 1
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 "NEC OHCI root hub" rev 1.00/1.00 addr 1
isa0 at glxpcib0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
mcclock0 at isa0 port 0x70/2: mc146818 or compatible
ykbec0 at isa0 port 0x381/3
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 "AMD OHCI root hub" rev 1.00/1.00 addr 1
clock0 at mainbus0: ticker on int5 using count register
apm0 at mainbus0
rum0 at uhub0 port 2 "Ralink Technology RT2573" rev 2.00/0.01 addr 2
rum0: MAC/BBP RT2573 (rev 0x2573a), RF RT2528, address 00:19:e0:81:e1:4e
umass0 at uhub1 port 1 configuration 1 interface 0 "Generic USB2.0-CRW" rev
2.00/58.87 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Generic-, Multi-Card, 1.00> SCSI0 0/direct
removable serial.0bda0158114173400000
urtw0 at uhub1 port 4 "Realtek RTL8187B" rev 2.00/2.00 addr 3
urtw0: RTL8187B rev E, address 00:17:c4:3d:33:f9
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
pmon bootpath: /dev/disk/wd0
boot device: wd0
root on wd0a (2c517028a6b8deda.a) swap on wd0b dump on wd0b
apm0: battery high
thanks,
Alan
