Dear Mailing Listeners,
It seems to me to get correct "sysctl hw.sensors" output
with respect to temperature and fan speed only when entering
"BIOS setup > Power menu > Hardware monitor" followed by
"BIOS Exit and Discard Changes" before booting the machine
(see the OpenBSD 5.0 dmesg output at the end of my post).
This behaviour has been observed from the very beginning after
machine assembly independently of using OpenBSD 4.8, 4.9 or 5.0:
Usual output: Output after visiting BIOS:
hw.sensors.cpu0.temp0=55.00 degC hw.sensors.cpu0.temp0=56.00 degC
hw.sensors.cpu1.temp0=55.00 degC hw.sensors.cpu1.temp0=56.00 degC
hw.sensors.cpu2.temp0=55.00 degC hw.sensors.cpu2.temp0=56.00 degC
hw.sensors.cpu3.temp0=55.00 degC hw.sensors.cpu3.temp0=56.00 degC
hw.sensors.sdtemp0.temp0=34.75 degC hw.sensors.sdtemp0.temp0=35.75
degC
hw.sensors.sdtemp1.temp0=34.50 degC hw.sensors.sdtemp1.temp0=35.00
degC
* hw.sensors.lm0.temp0=9.00 degC hw.sensors.lm0.temp0=22.00 degC
* hw.sensors.lm0.temp1=9.00 degC hw.sensors.lm0.temp1=22.00 degC
hw.sensors.lm0.temp2=23.00 degC hw.sensors.lm0.temp2=23.50 degC
* hw.sensors.lm0.fan0=843 RPM hw.sensors.lm0.fan0=998 RPM
* hw.sensors.lm0.fan1=815 RPM hw.sensors.lm0.fan1=1004 RPM
* hw.sensors.lm0.fan2=835 RPM hw.sensors.lm0.fan2=998 RPM
hw.sensors.lm0.volt0=0.90 VDC (VCore) hw.sensors.lm0.volt0=0.90 VDC
(VCore)
hw.sensors.lm0.volt1=11.40 VDC (+12V) hw.sensors.lm0.volt1=11.40 VDC
(+12V)
hw.sensors.lm0.volt2=3.36 VDC (+3.3V) hw.sensors.lm0.volt2=3.36 VDC
(+3.3V)
hw.sensors.lm0.volt3=3.36 VDC (+3.3V) hw.sensors.lm0.volt3=3.36 VDC
(+3.3V)
hw.sensors.lm0.volt4=-6.66 VDC (-12V) hw.sensors.lm0.volt4=-6.66 VDC
(-12V)
hw.sensors.lm0.volt5=1.66 VDC hw.sensors.lm0.volt5=1.66 VDC
hw.sensors.lm0.volt6=1.49 VDC hw.sensors.lm0.volt6=1.49 VDC
hw.sensors.lm0.volt7=3.33 VDC (3.3VSB) hw.sensors.lm0.volt7=3.33 VDC
(3.3VSB)
hw.sensors.lm0.volt8=1.60 VDC (VBAT) hw.sensors.lm0.volt8=1.62 VDC
(VBAT)
The emphasized lines significantly differ from each other and the right
column coincides with display messages of "BIOS setup > Power menu >
Hardware monitor".
Is there some other way to "initialize" the sensors without entering
BIOS setup?
Many thanks to the developers for their continuous work and development!
With best regards,
Jens
Here comes the dmesg output after booting recent OS version from USB device:
OpenBSD 5.0 (GENERIC.MP) #63: Wed Aug 17 10:14:30 MDT 2011
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 17169842176 (16374MB)
avail mem = 16698662912 (15925MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.6 @ 0xf06f0 (62 entries)
bios0: vendor American Megatrends Inc. version "0705" date 06/29/2010
bios0: ASUSTeK Computer INC. P7F-M WS
acpi0 at bios0: rev 2
acpi0: sleep states S0 S1 S3 S4 S5
acpi0: tables DSDT FACP APIC MCFG OEMB HPET SSDT
acpi0: wakeup devices BR1E(S4) UAR1(S4) PS2K(S4) PS2M(S4) EUSB(S4)
USB0(S4) USB1
(S4) USB2(S4) USB3(S4) USBE(S4) USB4(S4) USB5(S4) USB6(S4) BR21(S4)
BR22(S4) BR2
3(S4) P0P1(S4) P0P3(S4) P0P4(S4) P0P5(S4) P0P6(S4) USB8(S4) BR20(S4)
BR24(S4) BR
25(S4) BR26(S4) BR27(S4) PWRB(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Xeon(R) CPU L3426 @ 1.87GHz, 1866.97 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CF
LUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,S
SSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu0: 256KB 64b/line 8-way L2 cache
cpu0: apic clock running at 133MHz
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Xeon(R) CPU L3426 @ 1.87GHz, 1866.73 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CF
LUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,S
SSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu1: 256KB 64b/line 8-way L2 cache
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Xeon(R) CPU L3426 @ 1.87GHz, 1866.73 MHz
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CF
LUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,S
SSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu2: 256KB 64b/line 8-way L2 cache
cpu3 at mainbus0: apid 6 (application processor)
cpu3: Intel(R) Xeon(R) CPU L3426 @ 1.87GHz, 1866.73 MHz
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CF
LUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,S
SSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu3: 256KB 64b/line 8-way L2 cache
ioapic0 at mainbus0: apid 7 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 1, remapped to apid 7
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 7 (BR1E)
acpiprt2 at acpi0: bus -1 (BR21)
acpiprt3 at acpi0: bus -1 (BR22)
acpiprt4 at acpi0: bus -1 (BR23)
acpiprt5 at acpi0: bus -1 (P0P1)
acpiprt6 at acpi0: bus 1 (P0P3)
acpiprt7 at acpi0: bus -1 (P0P4)
acpiprt8 at acpi0: bus -1 (P0P5)
acpiprt9 at acpi0: bus -1 (P0P6)
acpiprt10 at acpi0: bus 2 (BR20)
acpiprt11 at acpi0: bus 5 (BR26)
acpiprt12 at acpi0: bus 6 (BR27)
acpicpu0 at acpi0: C3, C3, C1, PSS
acpicpu1 at acpi0: C3, C3, C1, PSS
acpicpu2 at acpi0: C3, C3, C1, PSS
acpicpu3 at acpi0: C3, C3, C1, PSS
acpibtn0 at acpi0: PWRB
ipmi at mainbus0 not configured
cpu0: Enhanced SpeedStep 1866 MHz: speeds: 1868, 1867, 1733, 1600, 1467,
1333, 1
200 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Core DMI" rev 0x11
ppb0 at pci0 dev 3 function 0 "Intel Core PCIE" rev 0x11: msi
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 vendor "ATI", unknown product 0x68f2 rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
azalia0 at pci1 dev 0 function 1 "ATI Radeon HD 5470 Audio" rev 0x00: msi
azalia0: no supported codecs
"Intel Core Management" rev 0x11 at pci0 dev 8 function 0 not configured
"Intel Core Scratch" rev 0x11 at pci0 dev 8 function 1 not configured
"Intel Core Control" rev 0x11 at pci0 dev 8 function 2 not configured
"Intel Core Misc" rev 0x11 at pci0 dev 8 function 3 not configured
"Intel Core QPI Link" rev 0x11 at pci0 dev 16 function 0 not configured
"Intel Core QPI Routing" rev 0x11 at pci0 dev 16 function 1 not configured
ehci0 at pci0 dev 26 function 0 "Intel 3400 USB" rev 0x05: apic 7 int 16
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia1 at pci0 dev 27 function 0 "Intel 3400 HD Audio" rev 0x05: msi
azalia1: no HD-Audio codecs
ppb1 at pci0 dev 28 function 0 "Intel 3400 PCIE" rev 0x05: msi
pci2 at ppb1 bus 2
em0 at pci2 dev 0 function 0 "Intel PRO/1000 PT (82575EB)" rev 0x02:
msi, addres
s 00:25:90:0f:20:d0
em1 at pci2 dev 0 function 1 "Intel PRO/1000 PT (82575EB)" rev 0x02:
msi, addres
s 00:25:90:0f:20:d1
ppb2 at pci0 dev 28 function 4 "Intel 3400 PCIE" rev 0x05
pci3 at ppb2 bus 3
ppb3 at pci0 dev 28 function 5 "Intel 3400 PCIE" rev 0x05
pci4 at ppb3 bus 4
ppb4 at pci0 dev 28 function 6 "Intel 3400 PCIE" rev 0x05
pci5 at ppb4 bus 5
em2 at pci5 dev 0 function 0 "Intel PRO/1000 MT (82574L)" rev 0x00: msi,
address
bc:ae:c5:05:5b:71
ppb5 at pci0 dev 28 function 7 "Intel 3400 PCIE" rev 0x05
pci6 at ppb5 bus 6
em3 at pci6 dev 0 function 0 "Intel PRO/1000 MT (82574L)" rev 0x00: msi,
address
bc:ae:c5:05:5b:b1
ehci1 at pci0 dev 29 function 0 "Intel 3400 USB" rev 0x05: apic 7 int 23
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb6 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xa5
pci7 at ppb6 bus 7
siop0 at pci7 dev 2 function 0 "Symbios Logic 53c875" rev 0x37: apic 7
int 21, u
sing 4K of on-board RAM
scsibus0 at siop0: 16 targets, initiator 7
siop1 at pci7 dev 2 function 1 "Symbios Logic 53c875" rev 0x37: apic 7
int 22, u
sing 4K of on-board RAM
scsibus1 at siop1: 16 targets, initiator 7
sd0 at scsibus1 targ 6 lun 0: <FUJITSU, MCJ3230SS, 0010> SCSI2 0/direct
removabl
e
pcib0 at pci0 dev 31 function 0 "Intel 3420 LPC" rev 0x05
ahci0 at pci0 dev 31 function 2 "Intel 3400 AHCI" rev 0x05: msi, AHCI 1.3
scsibus2 at ahci0: 32 targets
sd1 at scsibus2 targ 0 lun 0: <ATA, SSDSA2SH064G1GC, 045C> SCSI3
0/direct fixed
naa.5001517959470944
sd1: 61057MB, 512 bytes/sector, 125045424 sectors
sd2 at scsibus2 targ 1 lun 0: <ATA, SSDSA2SH032G1GN, 045C> SCSI3
0/direct fixed
naa.50015179594773ba
sd2: 30517MB, 512 bytes/sector, 62500000 sectors
cd0 at scsibus2 targ 5 lun 0: <Optiarc, DVD RW AD-7260S, 1.00> ATAPI
5/cdrom rem
ovable
ichiic0 at pci0 dev 31 function 3 "Intel 3400 SMBus" rev 0x05: apic 7 int 18
iic0 at ichiic0
sdtemp0 at iic0 addr 0x18: stts424e02
iic0: addr 0x19 00=00 01=00 02=00 03=00 04=00 05=c1 06=10 07=03 08=01
09=00 0a=0
0 0b=00 words 00=006f 01=0000 02=0000 03=0000 04=0000 05=c1d0 06=104a
07=0300
sdtemp1 at iic0 addr 0x1a: stts424e02
iic0: addr 0x1b 00=00 01=00 02=00 03=00 04=00 05=c2 06=10 07=03 08=01
09=00 0a=0
0 0b=00 words 00=006f 01=0000 02=0000 03=0000 04=0000 05=c200 06=104a
07=0300
spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM registered ECC PC3-10600 with
thermal
sensor
spdmem1 at iic0 addr 0x51: 4GB DDR3 SDRAM registered ECC PC3-10600 with
thermal
sensor
spdmem2 at iic0 addr 0x52: 4GB DDR3 SDRAM registered ECC PC3-10600 with
thermal
sensor
spdmem3 at iic0 addr 0x53: 4GB DDR3 SDRAM registered ECC PC3-10600 with
thermal
sensor
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lm0 at isa0 port 0x290/8: W83627DHG
mtrr: Pentium Pro MTRR support
siop1: target 6 now using 8 bit 20.0 MHz 15 REQ/ACK offset xfers
uhub2 at uhub0 port 1 "Intel Rate Matching Hub" rev 2.00/0.00 addr 2
uhub3 at uhub1 port 1 "Intel Rate Matching Hub" rev 2.00/0.00 addr 2
uhidev0 at uhub3 port 1 configuration 1 interface 0 "Logitech Optical
USB Mouse"
rev 2.00/3.40 addr 3
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
umass0 at uhub3 port 2 configuration 1 interface 0 "USB DISK Pro" rev
2.00/11.00
addr 4
umass0: using SCSI over Bulk-Only
scsibus3 at umass0: 2 targets, initiator 0
sd3 at scsibus3 targ 1 lun 0: <USB, DISK Pro, 1100> SCSI0 0/direct
removable ser
ial.090c1000012700032349
sd3: 1935MB, 512 bytes/sector, 3963904 sectors
vscsi0 at root
scsibus4 at vscsi0: 256 targets
softraid0 at root
scsibus5 at softraid0: 256 targets
root on sd3a swap on sd3b dump on sd3b
