there may be a bios option to stretch the image to fill the display. you could experiment with other display modes mentioned in vga(4) but i suspect they won't fill the screen.
On 2011-11-04, David Walker <[email protected]> wrote: > Hi. > > I got my hands on a ThinkPad 600 and only about 50% of the screen is > utilized on ttys in the middle. > Can someone please tell me where to look for this, man page or whatever. > > TIA > > Best wishes. > > OpenBSD 5.0 (GENERIC) #43: Wed Aug 17 10:10:52 MDT 2011 > [email protected]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Intel Pentium II ("GenuineIntel" 686-class, 512KB L2 cache) 266 MHz > cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,MMX,FXSR > real mem = 301330432 (287MB) > avail mem = 286351360 (273MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 09/18/99, BIOS32 rev. 0 @ 0xfd820 > apm0 at bios0: Power Management spec V1.2 > pcibios0 at bios0: rev 2.1 @ 0xfd880/0x800 > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf9e10/96 (4 entries) > pcibios0: PCI Exclusive IRQs: 11 > pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371AB PIIX4 ISA" rev > 0x00) > pcibios0: PCI bus #4 is the last bus > bios0: ROM list: 0xc0000/0xa000 > cpu0 at mainbus0: (uniprocessor) > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 0 function 0 "Intel 82443BX" rev 0x02 > cbb0 at pci0 dev 2 function 0 "TI PCI1250 CardBus" rev 0x02: irq 11 > cbb1 at pci0 dev 2 function 1 "TI PCI1250 CardBus" rev 0x02: irq 11 > vga1 at pci0 dev 3 function 0 "Neomagic Magicgraph NM2160" rev 0x01 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > piixpcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x01 > pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, > channel 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <HITACHI_DK23EA-60> > wd0: 16-sector PIO, LBA, 57231MB, 117210240 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > atapiscsi0 at pciide0 channel 1 drive 0 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <TOSHIBA, CD-ROM XM-1702BC, 1564> ATAPI > 5/cdrom removable > cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 > uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 11 > piixpm0 at pci0 dev 7 function 3 "Intel 82371AB Power" rev 0x01: SMI > iic0 at piixpm0 > cardslot0 at cbb0 slot 0 flags 0 > cardbus0 at cardslot0: bus 1 device 0 cacheline 0x8, lattimer 0xb0 > pcmcia0 at cardslot0 > cardslot1 at cbb1 slot 1 flags 0 > cardbus1 at cardslot1: bus 4 device 0 cacheline 0x8, lattimer 0xb0 > pcmcia1 at cardslot1 > isa0 at piixpcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pms0 at pckbc0 (aux slot) > pckbc0: using irq 12 for aux slot > wsmouse0 at pms0 mux 0 > sb0 at isa0 port 0x220/24 irq 5 drq 1: dsp v3.02 > midi0 at sb0: <SB MIDI UART> > audio0 at sb0 > opl at sb0 not configured > pcppi0 at isa0 port 0x61 > spkr0 at pcppi0 > lpt2 at isa0 port 0x3bc/4: polled > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > usb0 at uhci0: USB revision 1.0 > uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > mtrr: Pentium Pro MTRR support > vscsi0 at root > scsibus1 at vscsi0: 256 targets > softraid0 at root > scsibus2 at softraid0: 256 targets > root on wd0a (166b03162061edf6.a) swap on wd0b dump on wd0b > rl0 at cardbus0 dev 0 function 0 "Realtek 8139" rev 0x10: irq 11, > address 00:e0:98:b9:3f:78 > rlphy0 at rl0 phy 0: RTL internal PHY
