??, I am using the same chip connected through PCI to a Virtex-II Pro (PPC 405). I do not have an EEPROM connected to the chip. However, I am having problem with the code because it seems to be built specifically for processors that have coherent cache. So each time the code tries to execute I get a kernel panic. (kernel 2.4.26, with RTAI patch)
This occurs because in many places it executes a bottom-half spin lock before calling pci_free_consistent. This increments the bottom-half counter and so when pci_free_consistent is called it calls BUG(); and the whole thing goes Tango Uniform. I'm about to go through and try to fix this, but it seems like an extremely dangerous thing for me to play with. I seem to be able to get the eepro100.c code to work, but I was hoping to use the e100 driver to program an EEPROM on the board. ?? Joshua ???? wrote: >After i modified e100_init() in e100_main.c , the pci ethernet card could been >found : > >bash-2.05b# ifconfig -a >eth0 Link encap:Ethernet HWaddr FF:FF:FF:FF:FF:FF > BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > Memory:40000000-40000038 > >eth1 Link encap:Ethernet HWaddr 00:04:9F:00:15:2B > inet addr:198.87.102.215 Bcast:198.87.102.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:12606 errors:42 dropped:0 overruns:0 frame:0 > TX packets:7668 errors:3 dropped:0 overruns:3 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:10596597 (10.1 Mb) TX bytes:1218624 (1.1 Mb) > Interrupt:43 > >lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:4 errors:0 dropped:0 overruns:0 frame:0 > TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > >But i still could not config eth0: > >bash-2.05b# ifconfig eth0 198.87.102.140 >SIOCSIFFLAGS: Resource temporarily unavailable > >I noticed that there was message as blow during kernel bootup: > >POSIX conformance testing by UNIFIX >PCI: Probing PCI hardware >PCI: Cannot allocate resource region 0 of device 00:1a.0 >Linux NET4.0 for Linux 2.4 > >Intel(R) PRO/100 Network Driver - version 2.3.38-k1 >Copyright (c) 2004 Intel Corporation > >PCI: Enabling device 00:18.0 (0006 -> 0007) >e100: eth0: Intel(R) PRO/100 Network Connection >Hardware receive checksums enabled > >IP-Config: Failed to open eth0 > >what is wrong? > >Best regards > >Xiayu > > > > > > > >_______________________________________________ >Linuxppc-embedded mailing list >Linuxppc-embedded at ozlabs.org >https://ozlabs.org/mailman/listinfo/linuxppc-embedded > > > -- Xiphos Technologies (514) 848-9640 x227 (514) 848-9644 fax www.xiplink.com _______________________________________________ The information transmitted is intended only for the person or entity to which it is addressed and may contain confidential and/or privileged material. If you have received this in error, please contact the sender and delete this communication and any copy immediately. Thank you.
