Hi all,
We have downloaded freebios 1.0 and we are trying to boot freebios on National Geode GX1 processor based system. We were successful enough to create a new target in freebios and boot freebios on the board with bios output on serial port .
Also we tried to boot linux image minimal from freebios, but we are getting error saying error gunzip.
My board freebios log is as follows
--------------------------------------
LinuxBIOS-1.0.0 Mon Dec 6 13:40:00 IST 2004 starting...
Setting up default parameters for memory
Sizing memory
Probing for DIMM0
Found DIMM0
Page Size: 00001000
Component Banks: 4
Module Banks: 1
DIMM size: 04000000
Probing for DIMM1
Memory sizing done, MC_BANK_CFG = 0x00701420
Copying LinuxBIOS to ram.
Jumping to LinuxBIOS.
LinuxBIOS-1.0.0 Mon Dec 6 13:40:00 IST 2004 booting...
Finding PCI configuration type.
PCI: Using configuration type 1
Scanning PCI bus...PCI: pci_scan_bus for bus 0
PCI: 00:00.0 [1078/0001]
PCI: 00:0f.0 [10ec/8139]
PCI: 00:12.0 [1078/0100]
PCI: 00:12.1 [1078/0101]
PCI: 00:12.2 [1078/0102]
PCI: 00:12.3 [1078/0103]
PCI: 00:12.4 [1078/0104]
PCI: 00:13.0 [0e11/a0f8]
PCI: pci_scan_bus returning with max=00
done
Allocating PCI resources...
ASSIGN RESOURCES, bus 0
PCI: 00:0f.0 10 <- [0x00001000 - 0x000010ff] io
PCI: 00:0f.0 14 <- [0xfebfd000 - 0xfebfd0ff] mem
PCI: 00:12.1 10 <- [0xfebfe000 - 0xfebfe0ff] mem
PCI: 00:12.2 20 <- [0x00001400 - 0x0000147f] io
PCI: 00:12.3 10 <- [0xfebff000 - 0xfebff07f] mem
PCI: 00:12.4 10 <- [0xfebfb000 - 0xfebfbfff] mem
PCI: 00:13.0 10 <- [0xfebfc000 - 0xfebfcfff] mem
ASSIGNED RESOURCES, bus 0
Allocating VGA resource
done.
Enabling PCI resourcess...PCI: 00:00.0 cmd <- 07
PCI: 00:0f.0 cmd <- 03
PCI: 00:12.0 cmd <- 0f
PCI: 00:12.1 cmd <- 02
PCI: 00:12.2 cmd <- 01
PCI: 00:12.3 cmd <- 02
PCI: 00:12.4 cmd <- 03
PCI: 00:13.0 cmd <- 02
done.
Initializing PCI devices...
PCI devices initialized
DIMM0: 64MB (4kB page size, 4 component banks, 1 module banks)
DIMM1: empty
Reserving 4096kB for video memory
BC_DRAM_TOP = 0x03bfffff
MC_GBASE_ADD = 0x00000078
totalram: 60M
Initializing CPU #0
Enabling cache...done.Max cpuid index : 2 Vendor ID : Geode by NSC Processor Type : 0x00 Processor Family : 0x05 Processor Model : 0x04 Processor Mask : 0x00 Processor Stepping : 0x00 Feature flags : 0x00808131
Cache/TLB descriptor values: 1 reads required Desc 0x70 : UNKNOWN Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x80 : UNKNOWN Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null
done. CPU #0 Initialized Enable FLASH Set F0/0x52 to 0xee cs5530: Enabling Primary IDE Controller cs5530: Enabling Secondary IDE Controller Set F0/0x5b to |= 1 << 5(0x38) Final southbridge fixup F0/5c: 0x0000 cs5530: PCI INTA=9, INTB=10, INTC=11, INTD=15 F0/5c: 0xfba9 4d0: 0x00 4d1: 0x00 4d0: 0x00 4d1: 0x8e F0/5b = 0x38 cs5530: Enabling Primary IDE Controller F0/5b = 0x38 cs5530: USB is on INTA, IRQ 9 Final mainboard fixup Wrote linuxbios table at: 00000500 - 00000668 checksum 7862 Jumping to linuxbiosmain()...
Welcome to start32, the open sourced starter. This space will eventually hold more diagnostic information.
January 2000, James Hendricks, Dale Webster, and Ron Minnich. Version 0.1
34:init_bytes() - zkernel_start:0xc0000200 zkernel_mask:0x0000ffff Gunzip setup gunzip_setup output data is 0x00100000 Gunzipping boot code bad gzip magic numbers
--------------------------------------
Now My board has a DOC M-Sys 16MB, which consists of freedos in it's primary partition.
Can we boot freedos from the freebios ?
Bye R Arun Kumar
_______________________________________________ Linuxbios mailing list [EMAIL PROTECTED] http://www.clustermatic.org/mailman/listinfo/linuxbios
