PineCube is an IP camera development kit released by Pine64. It comes with the following compoents:
- A mainboard with Sochip S3 SoC, a 16MByte SPI Flash, AXP209 PMIC, a power-only microUSB connector, a USB Type-A connector, a 10/100Mbps Ethernet port and FPC connectors for camera and daughter board. - An OV5640-based camera module which is connected to the parallel CSI bus of the mainboard. - A daughterboard with several buttons, a SD slot, some IR LEDs, a microphone and a speaker connector. As the device tree is synchronized in a previous commit, just add it to Makefile, create a new MAINTAINER item and provide a defconfig. Signed-off-by: Icenowy Zheng <[email protected]> --- Changes since v2: - Add Makefile reference to DT. Changes since v1: - Dropped LDO3 quirk. arch/arm/dts/Makefile | 1 + board/sunxi/MAINTAINERS | 5 +++++ configs/pinecube_defconfig | 15 +++++++++++++++ 3 files changed, 21 insertions(+) create mode 100644 configs/pinecube_defconfig diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 7d1a369845..e6993733b0 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -587,6 +587,7 @@ dtb-$(CONFIG_MACH_SUN8I_R40) += \ sun8i-r40-bananapi-m2-ultra.dtb \ sun8i-v40-bananapi-m2-berry.dtb dtb-$(CONFIG_MACH_SUN8I_V3S) += \ + sun8i-s3-pinecube.dtb \ sun8i-v3s-licheepi-zero.dtb dtb-$(CONFIG_MACH_SUN50I_H5) += \ sun50i-h5-bananapi-m2-plus.dtb \ diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS index d3755ae41a..735801ae1d 100644 --- a/board/sunxi/MAINTAINERS +++ b/board/sunxi/MAINTAINERS @@ -440,6 +440,11 @@ M: Vasily Khoruzhick <[email protected]> S: Maintained F: configs/pinebook_defconfig +PINECUBE BOARD: +M: Icenowy Zheng <[email protected]> +S: Maintained +F: configs/pinecube_defconfig + PINE64 BOARDS M: Andre Przywara <[email protected]> S: Maintained diff --git a/configs/pinecube_defconfig b/configs/pinecube_defconfig new file mode 100644 index 0000000000..a8c404f6b1 --- /dev/null +++ b/configs/pinecube_defconfig @@ -0,0 +1,15 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_SPL=y +CONFIG_MACH_SUN8I_V3S=y +CONFIG_SUNXI_DRAM_DDR3_1333=y +CONFIG_DRAM_CLK=504 +CONFIG_DRAM_ODT_EN=y +CONFIG_I2C0_ENABLE=y +CONFIG_DEFAULT_DEVICE_TREE="sun8i-s3-pinecube" +CONFIG_SPL_I2C_SUPPORT=y +# CONFIG_NETDEVICES is not set +CONFIG_AXP209_POWER=y +CONFIG_AXP_DCDC2_VOLT=1250 +CONFIG_AXP_DCDC3_VOLT=3300 +CONFIG_CONS_INDEX=3 -- 2.28.0 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20201118102717.635129-1-icenowy%40aosc.io.
