From: Ondrej Jirman <[email protected]> The PinePhone has a Realtek rtl8723cs WiFi module.
On mainboard revisions 1.0 and 1.1, the reset input is always pulled high, so no power sequence is needed. On mainboard revision 1.2, the reset input is connected to PL2. Signed-off-by: Ondrej Jirman <[email protected]> Signed-off-by: Samuel Holland <[email protected]> --- .../allwinner/sun50i-a64-pinephone-1.2.dts | 9 ++++++++ .../dts/allwinner/sun50i-a64-pinephone.dtsi | 22 +++++++++++++++++++ 2 files changed, 31 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts index 94e4f11e0215..e7cf9d8577c1 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts @@ -8,6 +8,11 @@ / { model = "Pine64 PinePhone (1.2)"; compatible = "pine64,pinephone-1.2", "allwinner,sun50i-a64"; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + }; }; &backlight { @@ -39,6 +44,10 @@ &lis3mdl { interrupts = <1 1 IRQ_TYPE_EDGE_RISING>; /* PB1 */ }; +&mmc1 { + mmc-pwrseq = <&wifi_pwrseq>; +}; + &sgm3140 { enable-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ flash-gpios = <&pio 2 3 GPIO_ACTIVE_HIGH>; /* PC3 */ diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi index 9544d7658794..e173096a7e68 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi @@ -13,6 +13,7 @@ / { aliases { + ethernet0 = &rtl8723cs; serial0 = &uart0; }; @@ -49,6 +50,13 @@ red { }; }; + reg_vbat_wifi: vbat-wifi { + compatible = "regulator-fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vbat-wifi"; + }; + sgm3140: led-controller { compatible = "sgmicro,sgm3140"; vin-supply = <®_dcdc1>; @@ -216,6 +224,20 @@ &mmc0 { status = "okay"; }; +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_vbat_wifi>; + vqmmc-supply = <®_dldo4>; + bus-width = <4>; + non-removable; + status = "okay"; + + rtl8723cs: wifi@1 { + reg = <1>; + }; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins>; -- 2.26.2 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20201105054135.24860-6-samuel%40sholland.org.
