Hi,
On 16-03-15 10:04, Olliver Schinagl wrote:
Hey all,
On 16-03-15 09:12, Hans de Goede wrote:
Hi,
On 15-03-15 22:38, Paul Kocialkowski wrote:
As far as I know, there is currently no mechanism in place to give each
device a unique serial number, that would be shown in
e.g. /proc/cpuinfo. This can seem not very useful, but it would be
nice to have that for USB gadget drivers that make use of it (e.g. ADB on
Android, fastboot, etc). This would allow having multiple sunxi devices
connected at the same time.
Normally, the serial number has to be figured out by the bootloader and
passed to the kernel through ATAGs. In U-Boot, it is defined using
get_board_serial, that is not yet implemented on sunxi.
I'm interested in figuring out the best way to do this. As far as I can
see, Allwinner SoCs have some e-fuses, known as SID (Security ID):
http://linux-sunxi.org/SID_Register_Guide for which Oliver has written a
mainline Linux driver. Those should have device-specific values, except
when they are set to 0.
Do you have any better idea to do this, or is there some reference that
I am missing?
AFAIK the only way to do a serial number on sunxi devices is using the SID,
note that Oliver's driver will only work on A10, A13 and A20, with the
A31, A23 and others the SID is burned into the pmic rather then the SoC
I vaguely recall that the A31 had a SID aswell according to its datasheet
Yes it has a SID entry in its memory map, that is probably a copy and paste
error though,
the real SID is stored in the axp221, not in the A31 itself, reading from the
addresses in the memory map always returns 0 on all A31-s.
> I'll go over the datasheets for a23 and a33 to confirm on those, and will
look at the a31/a31s/a80's also.
itself, but it should be easy to implement get_board_serial() in u-boot
as we already have a sunxi_get_sid() helper to do that in a SoC
independent way (this is currently used to set the ethernet MAC address).
I'l slowly (in a few weeks time) working on a patch to get the mac from the
EEPROM for the olinuxino's, though i think we need to upgrade the i2c driver a
bit (multiple adapter support).
Hmm, not sure if that is really useful, 2 questions:
1) Is there anything wrong with the current SID based approach on the
olinuxino-s, AFAIK all olinuxino's have non pre-production SOCs and so
have proper SID-s and thus a proper MAC set.
2) Are the eeproms prepolulated on ALL olinuxino-s ? If they are not
populated from the factory, I see little added value and I think I may
end up nacking any patches for this, but first lets hear your arguments :)
Note that sunxi_get_sid() can fail, so you need to error check it,
and currently it will happily return an all 0 SID, you should probably
make it return an error in that case, as that check really belongs
inside sunxi_get_sid().
The big problem with the sunxi-sid, is that it can be often blank :S very
annoying. Also, which part of the SID do we want in /proc/cpuinfo? The one is
bigger then the other, though looking at
http://linux-sunxi.org/SID_Register_Guide there's a lot of non-uniqueness that
can be ignored (chip ID (1623 for example).
Often? In my experience it is empty on cubieboard2 and some early
mele A1000 models, and that is it.
Regards,
Hans
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
For more options, visit https://groups.google.com/d/optout.
