The documentation being added contains overall description of the
LED Flash Class and the related sysfs attributes.

Signed-off-by: Jacek Anaszewski <j.anaszew...@samsung.com>
Acked-by: Kyungmin Park <kyungmin.p...@samsung.com>
Cc: Bryan Wu <coolo...@gmail.com>
Cc: Richard Purdie <rpur...@rpsys.net>
---
 Documentation/leds/leds-class-flash.txt |   57 +++++++++++++++++++++++++++++++
 1 file changed, 57 insertions(+)
 create mode 100644 Documentation/leds/leds-class-flash.txt

diff --git a/Documentation/leds/leds-class-flash.txt 
b/Documentation/leds/leds-class-flash.txt
new file mode 100644
index 0000000..d80096b
--- /dev/null
+++ b/Documentation/leds/leds-class-flash.txt
@@ -0,0 +1,57 @@
+
+Flash LED handling under Linux
+==============================
+
+Some LED devices support two modes - torch and flash. In the LED subsystem
+those modes are supported by LED class (see Documentation/leds/leds-class.txt)
+and LED Flash class respectively. The torch mode related features are enabled
+by default and the flash ones only if a driver declares it by setting
+LED_DEV_CAP_FLASH flag.
+
+In order to enable support for flash LEDs CONFIG_LEDS_CLASS_FLASH symbol
+must be defined in the kernel config. A flash LED driver must register
+in the LED subsystem with led_classdev_flash_register function to gain flash
+related capabilities.
+
+There are flash LED devices which can control more than one LED and allow for
+strobing the sub-leds synchronously. A LED will be strobed synchronously with
+the one whose identifier is written to the flash_sync_strobe sysfs attribute.
+The list of available sub-led identifiers can be read from the 
available_sync_leds
+sysfs attribute. In order to enable the related settings the driver must set
+LED_DEV_CAP_SYNC_STROBE flag.
+
+Following sysfs attributes are exposed for controlling flash led devices:
+
+       - flash_brightness - flash LED brightness in microamperes (RW)
+       - max_flash_brightness - maximum available flash LED brightness (RO)
+       - flash_timeout - flash strobe duration in microseconds (RW)
+       - max_flash_timeout - maximum available flash strobe duration (RO)
+       - flash_strobe - flash strobe state (RW)
+       - available_sync_leds - list of sub-leds available for flash strobe
+                               synchronization (RO)
+       - flash_sync_strobe - identifier of the sub-led to synchronize the flash
+                             strobe with; 0 stands for no synchronization (RW)
+       - flash_fault - bitmask of flash faults that may have occurred
+                       possible flags are:
+               * 0x01 - flash controller voltage to the flash LED has exceeded
+                        the limit specific to the flash controller
+               * 0x02 - the flash strobe was still on when the timeout set by
+                        the user has expired; not all flash controllers may
+                        set this in all such conditions
+               * 0x04 - the flash controller has overheated
+               * 0x08 - the short circuit protection of the flash controller
+                        has been triggered
+               * 0x10 - current in the LED power supply has exceeded the limit
+                        specific to the flash controller
+               * 0x20 - the flash controller has detected a short or open
+                        circuit condition on the indicator LED
+               * 0x40 - flash controller voltage to the flash LED has been
+                        below the minimum limit specific to the flash
+               * 0x80 - the input voltage of the flash controller is below
+                        the limit under which strobing the flash at full
+                        current will not be possible. The condition persists
+                        until this flag is no longer set
+               * 0x100 - the temperature of the LED has exceeded its allowed
+                         upper limit
+
+               Flash faults are cleared, if possible, by reading the attribute.
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to