Dinesh
On Tue, Oct 15, 2013 at 11:24 AM, Dinesh Ram <[email protected]> wrote:
> This is the USB driver for the Silicon Labs development board.
> It contains the Si4713 FM transmitter chip.
>
I tried this driver again. The system attempts to probe the device but
it fails because the product revision read out of the USB device is
wrong.
[ 220.855158] usb 2-1.3.3: new full-speed USB device number 10 using ehci-pci
[ 220.949677] usb 2-1.3.3: New USB device found, idVendor=10c4, idProduct=8244
[ 220.949683] usb 2-1.3.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 220.949688] usb 2-1.3.3: Product: Si47xx Baseboard
[ 220.949691] usb 2-1.3.3: Manufacturer: SILICON LABORATORIES INC.
[ 220.949695] usb 2-1.3.3: SerialNumber: CBDA8-00-0
[ 220.950157] usbhid 2-1.3.3:1.0: couldn't find an input interrupt endpoint
[ 1014.981012] radio-usb-si4713 2-1.3.3:1.0: Si4713 development board
discovered: (10C4:8244)
[ 1015.870984] si4713 12-0063: IRQ not configured. Using timeouts.
[ 1015.943551] si4713 12-0063: Invalid product number <<< Here is
the code without modification
[ 1015.943556] si4713 12-0063: Failed to probe device information.
[ 1015.943568] si4713: probe of 12-0063 failed with error -22
[ 1015.943613] radio-usb-si4713 2-1.3.3:1.0: cannot get v4l2 subdevice
[ 1015.943672] usbcore: registered new interface driver radio-usb-si4713
[ 1274.419987] perf samples too long (2504 > 2500), lowering
kernel.perf_event_max_sample_rate to 50000
[ 1308.851059] usbcore: deregistering interface driver radio-usb-si4713
[ 1500.478308] radio-usb-si4713 2-1.3.3:1.0: Si4713 development board
discovered: (10C4:8244)
[ 1500.612240] si4713 12-0063: IRQ not configured. Using timeouts.
[ 1500.683489] si4713 12-0063: Invalid product number 0x15 <<< Here it
prints the PN read
[ 1500.683495] si4713 12-0063: Failed to probe device information.
[ 1500.683509] si4713: probe of 12-0063 failed with error -22
[ 1500.683558] radio-usb-si4713 2-1.3.3:1.0: cannot get v4l2 subdevice
[ 1500.683624] usbcore: registered new interface driver radio-usb-si4713
Here is simple diff of what I used to print the PN value:
diff --git a/drivers/media/radio/si4713/si4713.c
b/drivers/media/radio/si4713/si4713.c
index aadecb5..ee53584 100644
--- a/drivers/media/radio/si4713/si4713.c
+++ b/drivers/media/radio/si4713/si4713.c
@@ -464,7 +464,7 @@ static int si4713_checkrev(struct si4713_device *sdev)
v4l2_info(&sdev->sd, "chip found @ 0x%02x (%s)\n",
client->addr << 1, client->adapter->name);
} else {
- v4l2_err(&sdev->sd, "Invalid product number\n");
+ v4l2_err(&sdev->sd, "Invalid product number 0x%X\n", resp[1]);
rval = -EINVAL;
}
return rval;
It is expected to be 0x0D instead of 0x15, if I am not mistaken.
> Signed-off-by: Dinesh Ram <[email protected]>
> ---
> drivers/media/radio/si4713/Kconfig | 15 +
> drivers/media/radio/si4713/Makefile | 1 +
> drivers/media/radio/si4713/radio-usb-si4713.c | 540
> +++++++++++++++++++++++++
> 3 files changed, 556 insertions(+)
> create mode 100644 drivers/media/radio/si4713/radio-usb-si4713.c
>
> diff --git a/drivers/media/radio/si4713/Kconfig
> b/drivers/media/radio/si4713/Kconfig
> index ec640b8..a7c3ba8 100644
> --- a/drivers/media/radio/si4713/Kconfig
> +++ b/drivers/media/radio/si4713/Kconfig
> @@ -1,3 +1,18 @@
> +config USB_SI4713
> + tristate "Silicon Labs Si4713 FM Radio Transmitter support with USB"
> + depends on USB && RADIO_SI4713
> + select SI4713
> + ---help---
> + This is a driver for USB devices with the Silicon Labs SI4713
> + chip. Currently these devices are known to work.
> + - 10c4:8244: Silicon Labs FM Transmitter USB device.
> +
> + Say Y here if you want to connect this type of radio to your
> + computer's USB port.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called radio-usb-si4713.
> +
> config PLATFORM_SI4713
> tristate "Silicon Labs Si4713 FM Radio Transmitter support with I2C"
> depends on I2C && RADIO_SI4713
> diff --git a/drivers/media/radio/si4713/Makefile
> b/drivers/media/radio/si4713/Makefile
> index 9d0bd0e..6524674 100644
> --- a/drivers/media/radio/si4713/Makefile
> +++ b/drivers/media/radio/si4713/Makefile
> @@ -3,5 +3,6 @@
> #
>
> obj-$(CONFIG_I2C_SI4713) += si4713.o
> +obj-$(CONFIG_USB_SI4713) += radio-usb-si4713.o
> obj-$(CONFIG_PLATFORM_SI4713) += radio-platform-si4713.o
>
> diff --git a/drivers/media/radio/si4713/radio-usb-si4713.c
> b/drivers/media/radio/si4713/radio-usb-si4713.c
> new file mode 100644
> index 0000000..a75e2c8
> --- /dev/null
> +++ b/drivers/media/radio/si4713/radio-usb-si4713.c
> @@ -0,0 +1,540 @@
> +/*
> + * Copyright 2013 Cisco Systems, Inc. and/or its affiliates.
> + * All rights reserved.
> + *
> + * This program is free software; you may redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; version 2 of the License.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
> + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
> + * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
> + * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
> + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
> + * SOFTWARE.
> + */
> +
> +/* kernel includes */
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/usb.h>
> +#include <linux/init.h>
> +#include <linux/slab.h>
> +#include <linux/input.h>
> +#include <linux/mutex.h>
> +#include <linux/i2c.h>
> +/* V4l includes */
> +#include <linux/videodev2.h>
> +#include <media/v4l2-common.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-ioctl.h>
> +#include <media/v4l2-event.h>
> +#include <media/si4713.h>
> +
> +#include "si4713.h"
> +
> +/* driver and module definitions */
> +MODULE_AUTHOR("Dinesh Ram <[email protected]>");
> +MODULE_DESCRIPTION("Si4713 FM Transmitter USB driver");
> +MODULE_LICENSE("GPL v2");
> +
> +/* The Device announces itself as Cygnal Integrated Products, Inc. */
> +#define USB_SI4713_VENDOR 0x10c4
> +#define USB_SI4713_PRODUCT 0x8244
> +
> +#define BUFFER_LENGTH 64
> +#define USB_TIMEOUT 1000
> +#define USB_RESP_TIMEOUT 50000
> +
> +/* USB Device ID List */
> +static struct usb_device_id usb_si4713_usb_device_table[] = {
> + {USB_DEVICE_AND_INTERFACE_INFO(USB_SI4713_VENDOR, USB_SI4713_PRODUCT,
> + USB_CLASS_HID, 0, 0)
> },
> + { } /* Terminating entry
> */
> +};
> +
> +MODULE_DEVICE_TABLE(usb, usb_si4713_usb_device_table);
> +
> +struct si4713_usb_device {
> + struct usb_device *usbdev;
> + struct usb_interface *intf;
> + struct video_device vdev;
> + struct v4l2_device v4l2_dev;
> + struct v4l2_subdev *v4l2_subdev;
> + struct mutex lock;
> + struct i2c_adapter i2c_adapter;
> +
> + u8 *buffer;
> +};
> +
> +static inline struct si4713_usb_device *to_si4713_dev(struct v4l2_device
> *v4l2_dev)
> +{
> + return container_of(v4l2_dev, struct si4713_usb_device, v4l2_dev);
> +}
> +
> +static int vidioc_querycap(struct file *file, void *priv,
> + struct v4l2_capability *v)
> +{
> + struct si4713_usb_device *radio = video_drvdata(file);
> +
> + strlcpy(v->driver, "radio-usb-si4713", sizeof(v->driver));
> + strlcpy(v->card, "Si4713 FM Transmitter", sizeof(v->card));
> + usb_make_path(radio->usbdev, v->bus_info, sizeof(v->bus_info));
> + v->device_caps = V4L2_CAP_MODULATOR | V4L2_CAP_RDS_OUTPUT;
> + v->capabilities = v->device_caps | V4L2_CAP_DEVICE_CAPS;
> +
> + return 0;
> +}
> +
> +static int vidioc_g_modulator(struct file *file, void *priv,
> + struct v4l2_modulator *vm)
> +{
> + struct si4713_usb_device *radio = video_drvdata(file);
> +
> + return v4l2_subdev_call(radio->v4l2_subdev, tuner, g_modulator, vm);
> +}
> +
> +static int vidioc_s_modulator(struct file *file, void *priv,
> + const struct v4l2_modulator *vm)
> +{
> + struct si4713_usb_device *radio = video_drvdata(file);
> +
> + return v4l2_subdev_call(radio->v4l2_subdev, tuner, s_modulator, vm);
> +}
> +
> +static int vidioc_s_frequency(struct file *file, void *priv,
> + const struct v4l2_frequency *vf)
> +{
> + struct si4713_usb_device *radio = video_drvdata(file);
> +
> + return v4l2_subdev_call(radio->v4l2_subdev, tuner, s_frequency, vf);
> +}
> +
> +static int vidioc_g_frequency(struct file *file, void *priv,
> + struct v4l2_frequency *vf)
> +{
> + struct si4713_usb_device *radio = video_drvdata(file);
> +
> + return v4l2_subdev_call(radio->v4l2_subdev, tuner, g_frequency, vf);
> +}
> +
> +static const struct v4l2_ioctl_ops usb_si4713_ioctl_ops = {
> + .vidioc_querycap = vidioc_querycap,
> + .vidioc_g_modulator = vidioc_g_modulator,
> + .vidioc_s_modulator = vidioc_s_modulator,
> + .vidioc_g_frequency = vidioc_g_frequency,
> + .vidioc_s_frequency = vidioc_s_frequency,
> + .vidioc_log_status = v4l2_ctrl_log_status,
> + .vidioc_subscribe_event = v4l2_ctrl_subscribe_event,
> + .vidioc_unsubscribe_event = v4l2_event_unsubscribe,
> +};
> +
> +/* File system interface */
> +static const struct v4l2_file_operations usb_si4713_fops = {
> + .owner = THIS_MODULE,
> + .open = v4l2_fh_open,
> + .release = v4l2_fh_release,
> + .poll = v4l2_ctrl_poll,
> + .unlocked_ioctl = video_ioctl2,
> +};
> +
> +static void usb_si4713_video_device_release(struct v4l2_device *v4l2_dev)
> +{
> + struct si4713_usb_device *radio = to_si4713_dev(v4l2_dev);
> + struct i2c_adapter *adapter = &radio->i2c_adapter;
> +
> + i2c_del_adapter(adapter);
> + v4l2_device_unregister(&radio->v4l2_dev);
> + kfree(radio->buffer);
> + kfree(radio);
> +}
> +
> +/*
> + * This command sequence emulates the behaviour of the Windows driver.
> + * The structure of these commands was determined by sniffing the
> + * usb traffic of the device during startup.
> + * Most likely, these commands make some queries to the device.
> + * Commands are sent to enquire parameters like the bus mode,
> + * component revision, boot mode, the device serial number etc.
> + *
> + * These commands are necessary to be sent in this order during startup.
> + * The device fails to powerup if these commands are not sent.
> + *
> + * The complete list of startup commands is given in the start_seq table
> below.
> + */
> +static int si4713_send_startup_command(struct si4713_usb_device *radio)
> +{
> + unsigned long until_jiffies = jiffies +
> usecs_to_jiffies(USB_RESP_TIMEOUT) + 1;
> + u8 *buffer = radio->buffer;
> + int retval;
> +
> + /* send the command */
> + retval = usb_control_msg(radio->usbdev,
> usb_sndctrlpipe(radio->usbdev, 0),
> + 0x09, 0x21, 0x033f, 0, radio->buffer,
> + BUFFER_LENGTH, USB_TIMEOUT);
> + if (retval < 0)
> + return retval;
> +
> + for (;;) {
> + /* receive the response */
> + retval = usb_control_msg(radio->usbdev,
> usb_rcvctrlpipe(radio->usbdev, 0),
> + 0x01, 0xa1, 0x033f, 0, radio->buffer,
> + BUFFER_LENGTH, USB_TIMEOUT);
> + if (retval < 0)
> + return retval;
> + if (!radio->buffer[1]) {
> + /* USB traffic sniffing showed that some commands
> require
> + * additional checks. */
> + switch (buffer[1]) {
> + case 0x32:
> + if (radio->buffer[2] == 0)
> + return 0;
> + break;
> + case 0x14:
> + case 0x12:
> + if (radio->buffer[2] & SI4713_CTS)
> + return 0;
> + break;
> + case 0x06:
> + if ((radio->buffer[2] & SI4713_CTS) &&
> radio->buffer[9] == 0x08)
> + return 0;
> + break;
> + default:
> + return 0;
> + }
> + }
> + if (jiffies > until_jiffies)
> + return -EIO;
> + msleep(3);
> + }
> +
> + return retval;
> +}
> +
> +struct si4713_start_seq_table {
> + int len;
> + u8 payload[8];
> +};
> +
> +/*
> + * Some of the startup commands that could be recognized are :
> + * (0x03): Get serial number of the board (Response : CB000-00-00)
> + * (0x06, 0x03, 0x03, 0x08, 0x01, 0x0f) : Get Component revision
> + */
> +struct si4713_start_seq_table start_seq[] = {
> +
> + { 1, { 0x03 } },
> + { 2, { 0x32, 0x7f } },
> + { 6, { 0x06, 0x03, 0x03, 0x08, 0x01, 0x0f } },
> + { 2, { 0x14, 0x02 } },
> + { 2, { 0x09, 0x90 } },
> + { 3, { 0x08, 0x90, 0xfa } },
> + { 2, { 0x36, 0x01 } },
> + { 2, { 0x05, 0x03 } },
> + { 7, { 0x06, 0x00, 0x06, 0x0e, 0x01, 0x0f, 0x05 } },
> + { 1, { 0x12 } },
> + /* Commands that are sent after pressing the 'Initialize'
> + button in the windows application */
> + { 1, { 0x03 } },
> + { 1, { 0x01 } },
> + { 2, { 0x09, 0x90 } },
> + { 3, { 0x08, 0x90, 0xfa } },
> + { 1, { 0x34 } },
> + { 2, { 0x35, 0x01 } },
> + { 2, { 0x36, 0x01 } },
> + { 2, { 0x30, 0x09 } },
> + { 4, { 0x30, 0x06, 0x00, 0xe2 } },
> + { 3, { 0x31, 0x01, 0x30 } },
> + { 3, { 0x31, 0x04, 0x09 } },
> + { 2, { 0x05, 0x02 } },
> + { 6, { 0x06, 0x03, 0x03, 0x08, 0x01, 0x0f } },
> +};
> +
> +static int si4713_start_seq(struct si4713_usb_device *radio)
> +{
> + int retval = 0;
> + int i;
> +
> + radio->buffer[0] = 0x3f;
> +
> + for (i = 0; i < ARRAY_SIZE(start_seq); i++) {
> + int len = start_seq[i].len;
> + u8 *payload = start_seq[i].payload;
> +
> + memcpy(radio->buffer + 1, payload, len);
> + memset(radio->buffer + len + 1, 0, BUFFER_LENGTH - 1 - len);
> + retval = si4713_send_startup_command(radio);
> + }
> +
> + return retval;
> +}
> +
> +static struct i2c_board_info si4713_board_info = {
> + I2C_BOARD_INFO("si4713", SI4713_I2C_ADDR_BUSEN_HIGH),
> +};
> +
> +struct si4713_command_table {
> + int command_id;
> + u8 payload[8];
> +};
> +
> +/*
> + * Structure of a command :
> + * Byte 1 : 0x3f (always)
> + * Byte 2 : 0x06 (send a command)
> + * Byte 3 : Unknown
> + * Byte 4 : Number of arguments + 1 (for the command byte)
> + * Byte 5 : Number of response bytes
> + */
> +struct si4713_command_table command_table[] = {
> +
> + { SI4713_CMD_POWER_UP, { 0x00, SI4713_PWUP_NARGS + 1,
> SI4713_PWUP_NRESP} },
> + { SI4713_CMD_GET_REV, { 0x03, 0x01, SI4713_GETREV_NRESP } },
> + { SI4713_CMD_POWER_DOWN, { 0x00, 0x01, SI4713_PWDN_NRESP} },
> + { SI4713_CMD_SET_PROPERTY, { 0x00, SI4713_SET_PROP_NARGS + 1,
> SI4713_SET_PROP_NRESP } },
> + { SI4713_CMD_GET_PROPERTY, { 0x00, SI4713_GET_PROP_NARGS + 1,
> SI4713_GET_PROP_NRESP } },
> + { SI4713_CMD_TX_TUNE_FREQ, { 0x03, SI4713_TXFREQ_NARGS + 1,
> SI4713_TXFREQ_NRESP } },
> + { SI4713_CMD_TX_TUNE_POWER, { 0x03, SI4713_TXPWR_NARGS + 1,
> SI4713_TXPWR_NRESP } },
> + { SI4713_CMD_TX_TUNE_MEASURE, { 0x03, SI4713_TXMEA_NARGS + 1,
> SI4713_TXMEA_NRESP } },
> + { SI4713_CMD_TX_TUNE_STATUS, { 0x00, SI4713_TXSTATUS_NARGS + 1,
> SI4713_TXSTATUS_NRESP } },
> + { SI4713_CMD_TX_ASQ_STATUS, { 0x03, SI4713_ASQSTATUS_NARGS + 1,
> SI4713_ASQSTATUS_NRESP } },
> + { SI4713_CMD_GET_INT_STATUS, { 0x03, 0x01, SI4713_GET_STATUS_NRESP
> } },
> + { SI4713_CMD_TX_RDS_BUFF, { 0x03, SI4713_RDSBUFF_NARGS + 1,
> SI4713_RDSBUFF_NRESP } },
> + { SI4713_CMD_TX_RDS_PS, { 0x00, SI4713_RDSPS_NARGS + 1,
> SI4713_RDSPS_NRESP } },
> +};
> +
> +static int send_command(struct si4713_usb_device *radio, u8 *payload, char
> *data, int len)
> +{
> + int retval;
> +
> + radio->buffer[0] = 0x3f;
> + radio->buffer[1] = 0x06;
> +
> + memcpy(radio->buffer + 2, payload, 3);
> + memcpy(radio->buffer + 5, data, len);
> + memset(radio->buffer + 5 + len, 0, BUFFER_LENGTH - 5 - len);
> +
> + /* send the command */
> + retval = usb_control_msg(radio->usbdev,
> usb_sndctrlpipe(radio->usbdev, 0),
> + 0x09, 0x21, 0x033f, 0, radio->buffer,
> + BUFFER_LENGTH, USB_TIMEOUT);
> +
> + return retval < 0 ? retval : 0;
> +}
> +
> +static int si4713_i2c_read(struct si4713_usb_device *radio, char *data, int
> len)
> +{
> + unsigned long until_jiffies = jiffies +
> usecs_to_jiffies(USB_RESP_TIMEOUT) + 1;
> + int retval;
> +
> + /* receive the response */
> + for (;;) {
> + retval = usb_control_msg(radio->usbdev,
> + usb_rcvctrlpipe(radio->usbdev, 0),
> + 0x01, 0xa1, 0x033f, 0, radio->buffer,
> + BUFFER_LENGTH, USB_TIMEOUT);
> + if (retval < 0)
> + return retval;
> +
> + /*
> + * Check that we get a valid reply back (buffer[1] == 0) and
> + * that CTS is set before returning, otherwise we wait and try
> + * again. The i2c driver also does the CTS check, but the
> timeouts
> + * used there are much too small for this USB driver, so we
> wait
> + * for it here.
> + */
> + if (radio->buffer[1] == 0 && (radio->buffer[2] & SI4713_CTS))
> {
> + memcpy(data, radio->buffer + 2, len);
> + return 0;
> + }
> + if (jiffies > until_jiffies) {
> + /* Zero the status value, ensuring CTS isn't set */
> + data[0] = 0;
> + return 0;
> + }
> + msleep(3);
> + }
> +}
> +
> +static int si4713_i2c_write(struct si4713_usb_device *radio, char *data, int
> len)
> +{
> + int retval = -EINVAL;
> + int i;
> +
> + if (len > BUFFER_LENGTH - 5)
> + return -EINVAL;
> +
> + for (i = 0; i < ARRAY_SIZE(command_table); i++) {
> + if (data[0] == command_table[i].command_id)
> + retval = send_command(radio, command_table[i].payload,
> + data, len);
> + }
> +
> + return retval < 0 ? retval : 0;
> +}
> +
> +static int si4713_transfer(struct i2c_adapter *i2c_adapter,
> + struct i2c_msg *msgs, int num)
> +{
> + struct si4713_usb_device *radio = i2c_get_adapdata(i2c_adapter);
> + int retval = -EINVAL;
> + int i;
> +
> + if (num <= 0)
> + return 0;
> +
> + for (i = 0; i < num; i++) {
> + if (msgs[i].flags & I2C_M_RD)
> + retval = si4713_i2c_read(radio, msgs[i].buf,
> msgs[i].len);
> + else
> + retval = si4713_i2c_write(radio, msgs[i].buf,
> msgs[i].len);
> + if (retval)
> + break;
> + }
> +
> + return retval ? retval : num;
> +}
> +
> +static u32 si4713_functionality(struct i2c_adapter *adapter)
> +{
> + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
> +}
> +
> +static struct i2c_algorithm si4713_algo = {
> + .master_xfer = si4713_transfer,
> + .functionality = si4713_functionality,
> +};
> +
> +/* This name value shows up in the sysfs filename associated
> + with this I2C adapter */
> +static struct i2c_adapter si4713_i2c_adapter_template = {
> + .name = "si4713-i2c",
> + .owner = THIS_MODULE,
> + .algo = &si4713_algo,
> +};
> +
> +int si4713_register_i2c_adapter(struct si4713_usb_device *radio)
> +{
> + radio->i2c_adapter = si4713_i2c_adapter_template;
> + /* set up sysfs linkage to our parent device */
> + radio->i2c_adapter.dev.parent = &radio->usbdev->dev;
> + i2c_set_adapdata(&radio->i2c_adapter, radio);
> +
> + return i2c_add_adapter(&radio->i2c_adapter);
> +}
> +
> +/* check if the device is present and register with v4l and usb if it is */
> +static int usb_si4713_probe(struct usb_interface *intf,
> + const struct usb_device_id *id)
> +{
> + struct si4713_usb_device *radio;
> + struct i2c_adapter *adapter;
> + struct v4l2_subdev *sd;
> + int retval = -ENOMEM;
> +
> + dev_info(&intf->dev, "Si4713 development board discovered:
> (%04X:%04X)\n",
> + id->idVendor, id->idProduct);
> +
> + /* Initialize local device structure */
> + radio = kzalloc(sizeof(struct si4713_usb_device), GFP_KERNEL);
> + if (radio)
> + radio->buffer = kmalloc(BUFFER_LENGTH, GFP_KERNEL);
> +
> + if (!radio || !radio->buffer) {
> + dev_err(&intf->dev, "kmalloc for si4713_usb_device failed\n");
> + kfree(radio);
> + return -ENOMEM;
> + }
> +
> + mutex_init(&radio->lock);
> +
> + radio->usbdev = interface_to_usbdev(intf);
> + radio->intf = intf;
> + usb_set_intfdata(intf, &radio->v4l2_dev);
> +
> + retval = si4713_start_seq(radio);
> + if (retval < 0)
> + goto err_v4l2;
> +
> + retval = v4l2_device_register(&intf->dev, &radio->v4l2_dev);
> + if (retval < 0) {
> + dev_err(&intf->dev, "couldn't register v4l2_device\n");
> + goto err_v4l2;
> + }
> +
> + retval = si4713_register_i2c_adapter(radio);
> + if (retval < 0) {
> + dev_err(&intf->dev, "could not register i2c device\n");
> + goto err_i2cdev;
> + }
> +
> + adapter = &radio->i2c_adapter;
> + sd = v4l2_i2c_new_subdev_board(&radio->v4l2_dev, adapter,
> + &si4713_board_info, NULL);
> + radio->v4l2_subdev = sd;
> + if (!sd) {
> + dev_err(&intf->dev, "cannot get v4l2 subdevice\n");
> + retval = -ENODEV;
> + goto del_adapter;
> + }
> +
> + radio->vdev.ctrl_handler = sd->ctrl_handler;
> + radio->v4l2_dev.release = usb_si4713_video_device_release;
> + strlcpy(radio->vdev.name, radio->v4l2_dev.name,
> + sizeof(radio->vdev.name));
> + radio->vdev.v4l2_dev = &radio->v4l2_dev;
> + radio->vdev.fops = &usb_si4713_fops;
> + radio->vdev.ioctl_ops = &usb_si4713_ioctl_ops;
> + radio->vdev.lock = &radio->lock;
> + radio->vdev.release = video_device_release_empty;
> + radio->vdev.vfl_dir = VFL_DIR_TX;
> +
> + video_set_drvdata(&radio->vdev, radio);
> + set_bit(V4L2_FL_USE_FH_PRIO, &radio->vdev.flags);
> +
> + retval = video_register_device(&radio->vdev, VFL_TYPE_RADIO, -1);
> + if (retval < 0) {
> + dev_err(&intf->dev, "could not register video device\n");
> + goto del_adapter;
> + }
> +
> + dev_info(&intf->dev, "V4L2 device registered as %s\n",
> + video_device_node_name(&radio->vdev));
> +
> + return 0;
> +
> +del_adapter:
> + i2c_del_adapter(adapter);
> +err_i2cdev:
> + v4l2_device_unregister(&radio->v4l2_dev);
> +err_v4l2:
> + kfree(radio->buffer);
> + kfree(radio);
> + return retval;
> +}
> +
> +static void usb_si4713_disconnect(struct usb_interface *intf)
> +{
> + struct si4713_usb_device *radio =
> to_si4713_dev(usb_get_intfdata(intf));
> +
> + dev_info(&intf->dev, "Si4713 development board now disconnected\n");
> +
> + mutex_lock(&radio->lock);
> + usb_set_intfdata(intf, NULL);
> + video_unregister_device(&radio->vdev);
> + v4l2_device_disconnect(&radio->v4l2_dev);
> + mutex_unlock(&radio->lock);
> + v4l2_device_put(&radio->v4l2_dev);
> +}
> +
> +/* USB subsystem interface */
> +static struct usb_driver usb_si4713_driver = {
> + .name = "radio-usb-si4713",
> + .probe = usb_si4713_probe,
> + .disconnect = usb_si4713_disconnect,
> + .id_table = usb_si4713_usb_device_table,
> +};
> +
> +module_usb_driver(usb_si4713_driver);
> --
> 1.7.9.5
>
--
Eduardo Bezerra Valentin
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
