On 10/02/2012 09:33 AM, Guennadi Liakhovetski wrote:
> Hi Rob
>
> On Tue, 2 Oct 2012, Rob Herring wrote:
>
>> On 09/27/2012 09:07 AM, Guennadi Liakhovetski wrote:
>>> This patch adds a document, describing common V4L2 device tree bindings.
>>>
>>> Co-authored-by: Sylwester Nawrocki <s.nawro...@samsung.com>
>>> Signed-off-by: Guennadi Liakhovetski <g.liakhovet...@gmx.de>
>>> ---
>>> Documentation/devicetree/bindings/media/v4l2.txt | 162
>>> ++++++++++++++++++++++
>>> 1 files changed, 162 insertions(+), 0 deletions(-)
>>> create mode 100644 Documentation/devicetree/bindings/media/v4l2.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/media/v4l2.txt
>>> b/Documentation/devicetree/bindings/media/v4l2.txt
>>> new file mode 100644
>>> index 0000000..b8b3f41
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/media/v4l2.txt
>>> @@ -0,0 +1,162 @@
>>> +Video4Linux Version 2 (V4L2)
>>
>> DT describes the h/w, but V4L2 is Linux specific. I think the binding
>> looks pretty good in terms of it is describing the h/w and not V4L2
>> components or settings. So in this case it's really just the name of the
>> file and title I have issue with.
>
> Hm, I see your point, then, I guess, you'd also like the file name
> changed. What should we use then? Just "video?" But there's already a
> whole directory Documentation/devicetree/bindings/video dedicated to
> graphics output (drm, fbdev). "video-camera" or "video-capture?" But this
> file shall also be describing video output. Use "video.txt" and describe
> inside what exactly this file is for?
Video output will probably have a lot of overlap with the graphics side.
How about video-interfaces.txt?
>
>>
>> One other comment below:
>>
>>> +
>>> +General concept
>>> +---------------
>>> +
>>> +Video pipelines consist of external devices, e.g. camera sensors,
>>> controlled
>>> +over an I2C, SPI or UART bus, and SoC internal IP blocks, including video
>>> DMA
>>> +engines and video data processors.
>>> +
>>> +SoC internal blocks are described by DT nodes, placed similarly to other
>>> SoC
>>> +blocks. External devices are represented as child nodes of their
>>> respective bus
>>> +controller nodes, e.g. I2C.
>>> +
>>> +Data interfaces on all video devices are described by "port" child DT
>>> nodes.
>>> +Configuration of a port depends on other devices participating in the data
>>> +transfer and is described by "link" DT nodes, specified as children of the
>>> +"port" nodes:
>>> +
>>> +/foo {
>>> + port@0 {
>>> + link@0 { ... };
>>> + link@1 { ... };
>>> + };
>>> + port@1 { ... };
>>> +};
>>> +
>>> +If a port can be configured to work with more than one other device on the
>>> same
>>> +bus, a "link" child DT node must be provided for each of them. If more
>>> than one
>>> +port is present on a device or more than one link is connected to a port, a
>>> +common scheme, using "#address-cells," "#size-cells" and "reg" properties
>>> is
>>> +used.
>>> +
>>> +Optional link properties:
>>> +- remote: phandle to the other endpoint link DT node.
>>
>> This name is a little vague. Perhaps "endpoint" would be better.
>
> "endpoint" can also refer to something local like in USB case. Maybe
> rather the description of the "remote" property should be improved?
>
remote-endpoint?
> Thanks
> Guennadi
>
>>
>> Rob
>>
>>> +- slave-mode: a boolean property, run the link in slave mode. Default is
>>> master
>>> + mode.
>>> +- data-shift: on parallel data busses, if data-width is used to specify the
>>> + number of data lines, data-shift can be used to specify which data lines
>>> are
>>> + used, e.g. "data-width=<10>; data-shift=<2>;" means, that lines 9:2 are
>>> used.
>>> +- hsync-active: 1 or 0 for active-high or -low HSYNC signal polarity
>>> + respectively.
>>> +- vsync-active: ditto for VSYNC. Note, that if HSYNC and VSYNC polarities
>>> are
>>> + not specified, embedded synchronisation may be required, where supported.
>>> +- data-active: similar to HSYNC and VSYNC specifies data line polarity.
>>> +- field-even-active: field signal level during the even field data
>>> transmission.
>>> +- pclk-sample: rising (1) or falling (0) edge to sample the pixel clock
>>> pin.
>>> +- data-lanes: array of serial, e.g. MIPI CSI-2, data hardware lane numbers
>>> in
>>> + the ascending order, beginning with logical lane 0.
>>> +- clock-lanes: hardware lane number, used for the clock lane.
>>> +- clock-noncontinuous: a boolean property to allow MIPI CSI-2
>>> non-continuous
>>> + clock mode.
>>> +
>>> +Example:
>>> +
>>> + ceu0: ceu@0xfe910000 {
>>> + compatible = "renesas,sh-mobile-ceu";
>>> + reg = <0xfe910000 0xa0>;
>>> + interrupts = <0x880>;
>>> +
>>> + mclk: master_clock {
>>> + compatible = "renesas,ceu-clock";
>>> + #clock-cells = <1>;
>>> + clock-frequency = <50000000>; /* max clock frequency
>>> */
>>> + clock-output-names = "mclk";
>>> + };
>>> +
>>> + port {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + ceu0_1: link@1 {
>>> + reg = <1>; /* local link # */
>>> + remote = <&ov772x_1_1>; /* remote phandle */
>>> + bus-width = <8>; /* used data lines */
>>> + data-shift = <0>; /* lines 7:0 are used */
>>> +
>>> + /* If [hv]sync-active are missing, embedded
>>> bt.605 sync is used */
>>> + hsync-active = <1>; /* active high */
>>> + vsync-active = <1>; /* active high */
>>> + data-active = <1>; /* active high */
>>> + pclk-sample = <1>; /* rising */
>>> + };
>>> +
>>> + ceu0_0: link@0 {
>>> + reg = <0>;
>>> + remote = <&csi2_2>;
>>> + immutable;
>>> + };
>>> + };
>>> + };
>>> +
>>> + i2c0: i2c@0xfff20000 {
>>> + ...
>>> + ov772x_1: camera@0x21 {
>>> + compatible = "omnivision,ov772x";
>>> + reg = <0x21>;
>>> + vddio-supply = <®ulator1>;
>>> + vddcore-supply = <®ulator2>;
>>> +
>>> + clock-frequency = <20000000>;
>>> + clocks = <&mclk 0>;
>>> + clock-names = "xclk";
>>> +
>>> + port {
>>> + /* With 1 link per port no need in addresses */
>>> + ov772x_1_1: link {
>>> + bus-width = <8>;
>>> + remote = <&ceu0_1>;
>>> + hsync-active = <1>;
>>> + vsync-active = <0>; /* who came up
>>> with an inverter here?... */
>>> + data-active = <1>;
>>> + pclk-sample = <1>;
>>> + };
>>> + };
>>> + };
>>> +
>>> + imx074: camera@0x1a {
>>> + compatible = "sony,imx074";
>>> + reg = <0x1a>;
>>> + vddio-supply = <®ulator1>;
>>> + vddcore-supply = <®ulator2>;
>>> +
>>> + clock-frequency = <30000000>; /* shared clock with
>>> ov772x_1 */
>>> + clocks = <&mclk 0>;
>>> + clock-names = "sysclk"; /* assuming this is the
>>> name in the datasheet */
>>> +
>>> + port {
>>> + imx074_1: link {
>>> + clock-lanes = <0>;
>>> + data-lanes = <1>, <2>;
>>> + remote = <&csi2_1>;
>>> + };
>>> + };
>>> + };
>>> + };
>>> +
>>> + csi2: csi2@0xffc90000 {
>>> + compatible = "renesas,sh-mobile-csi2";
>>> + reg = <0xffc90000 0x1000>;
>>> + interrupts = <0x17a0>;
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + port@1 {
>>> + compatible = "renesas,csi2c"; /* one of CSI2I and
>>> CSI2C */
>>> + reg = <1>; /* CSI-2 PHY #1 of 2:
>>> PHY_S, PHY_M has port address 0, is unused */
>>> +
>>> + csi2_1: link {
>>> + clock-lanes = <0>;
>>> + data-lanes = <2>, <1>;
>>> + remote = <&imx074_1>;
>>> + };
>>> + };
>>> + port@2 {
>>> + reg = <2>; /* port 2: link to the
>>> CEU */
>>> +
>>> + csi2_2: link {
>>> + immutable;
>>> + remote = <&ceu0_0>;
>>> + };
>>> + };
>>> + };
>>>
>>
>
> ---
> Guennadi Liakhovetski, Ph.D.
> Freelance Open-Source Software Developer
> http://www.open-technology.de/
>
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
