In radio mode, no frequency offset is needed. While at it, split off the
frequency offset computation for digital TV into a separate function.
---
drivers/media/common/tuners/tuner-xc2028.c | 137 +++++++++++++++-------------
1 files changed, 75 insertions(+), 62 deletions(-)
diff --git a/drivers/media/common/tuners/tuner-xc2028.c
b/drivers/media/common/tuners/tuner-xc2028.c
index b6b2868..8e53e5e 100644
--- a/drivers/media/common/tuners/tuner-xc2028.c
+++ b/drivers/media/common/tuners/tuner-xc2028.c
@@ -913,6 +913,66 @@ ret:
#define DIV 15625
+static u32 digital_freq_offset(struct xc2028_data *priv, u32 freq)
+{
+ u32 offset = 0;
+
+ /*
+ * Adjust to the center frequency. This is calculated by the
+ * formula: offset = 1.25MHz - BW/2
+ * For DTV 7/8, the firmware uses BW = 8000, so it needs a
+ * further adjustment to get the frequency center on VHF
+ */
+ if (priv->cur_fw.type & DTV6)
+ offset = 1750000;
+ else if (priv->cur_fw.type & DTV7)
+ offset = 2250000;
+ else /* DTV8 or DTV78 */
+ offset = 2750000;
+
+ if ((priv->cur_fw.type & DTV78) && freq < 470000000)
+ offset -= 500000;
+
+ /*
+ * xc3028 additional "magic"
+ * Depending on the firmware version, it needs some adjustments
+ * to properly centralize the frequency. This seems to be
+ * needed to compensate the SCODE table adjustments made by
+ * newer firmwares
+ */
+
+#if 1
+ /*
+ * The proper adjustment would be to do it at s-code table.
+ * However, this didn't work, as reported by
+ * Robert Lowery <rglow...@exemail.com.au>
+ */
+
+ if (priv->cur_fw.type & DTV7)
+ offset += 500000;
+
+#else
+ /*
+ * Still need tests for XC3028L (firmware 3.2 or upper)
+ * So, for now, let's just comment the per-firmware
+ * version of this change. Reports with xc3028l working
+ * with and without the lines bellow are welcome
+ */
+
+ if (priv->firm_version < 0x0302) {
+ if (priv->cur_fw.type & DTV7)
+ offset += 500000;
+ } else {
+ if (priv->cur_fw.type & DTV7)
+ offset -= 300000;
+ else if (type != ATSC) /* DVB @6MHz, DTV 8 and DTV 7/8 */
+ offset += 200000;
+ }
+#endif
+
+ return offset;
+}
+
static int generic_set_freq(struct dvb_frontend *fe, u32 freq /* in HZ */,
enum v4l2_tuner_type new_type,
unsigned int type,
@@ -933,75 +993,28 @@ static int generic_set_freq(struct dvb_frontend *fe, u32
freq /* in HZ */,
if (check_firmware(fe, type, std, int_freq) < 0)
goto ret;
- /* On some cases xc2028 can disable video output, if
- * very weak signals are received. By sending a soft
- * reset, this is re-enabled. So, it is better to always
- * send a soft reset before changing channels, to be sure
- * that xc2028 will be in a safe state.
- * Maybe this might also be needed for DTV.
- */
- if (new_type == V4L2_TUNER_ANALOG_TV) {
+ switch (new_type) {
+ case V4L2_TUNER_ANALOG_TV:
+ /* On some cases xc2028 can disable video output, if
+ * very weak signals are received. By sending a soft
+ * reset, this is re-enabled. So, it is better to always
+ * send a soft reset before changing channels, to be sure
+ * that xc2028 will be in a safe state.
+ * Maybe this might also be needed for DTV.
+ */
rc = send_seq(priv, {0x00, 0x00});
-
+ /* fall through */
+ case V4L2_TUNER_RADIO:
/* Analog modes require offset = 0 */
- } else {
+ break;
+ case V4L2_TUNER_DIGITAL_TV:
/*
* Digital modes require an offset to adjust to the
* proper frequency. The offset depends on what
* firmware version is used.
*/
-
- /*
- * Adjust to the center frequency. This is calculated by the
- * formula: offset = 1.25MHz - BW/2
- * For DTV 7/8, the firmware uses BW = 8000, so it needs a
- * further adjustment to get the frequency center on VHF
- */
- if (priv->cur_fw.type & DTV6)
- offset = 1750000;
- else if (priv->cur_fw.type & DTV7)
- offset = 2250000;
- else /* DTV8 or DTV78 */
- offset = 2750000;
- if ((priv->cur_fw.type & DTV78) && freq < 470000000)
- offset -= 500000;
-
- /*
- * xc3028 additional "magic"
- * Depending on the firmware version, it needs some adjustments
- * to properly centralize the frequency. This seems to be
- * needed to compensate the SCODE table adjustments made by
- * newer firmwares
- */
-
-#if 1
- /*
- * The proper adjustment would be to do it at s-code table.
- * However, this didn't work, as reported by
- * Robert Lowery <rglow...@exemail.com.au>
- */
-
- if (priv->cur_fw.type & DTV7)
- offset += 500000;
-
-#else
- /*
- * Still need tests for XC3028L (firmware 3.2 or upper)
- * So, for now, let's just comment the per-firmware
- * version of this change. Reports with xc3028l working
- * with and without the lines bellow are welcome
- */
-
- if (priv->firm_version < 0x0302) {
- if (priv->cur_fw.type & DTV7)
- offset += 500000;
- } else {
- if (priv->cur_fw.type & DTV7)
- offset -= 300000;
- else if (type != ATSC) /* DVB @6MHz, DTV 8 and DTV 7/8
*/
- offset += 200000;
- }
-#endif
+ offset = digital_freq_offset(priv, freq);
+ break;
}
div = (freq - offset + DIV / 2) / DIV;
--
1.7.6
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
