On 7/15/19 11:21 PM, Sean Young wrote:
On Tue, Jul 09, 2019 at 08:39:32PM +0200, Jan Pieter van Woerkom wrote:
From: Jan Pieter van Woerkom <j...@jpvw.nl>
Adds support for the "Mygica T230C v2" into the "dvbsky" driver.
A small enhancement is also needed in the si2168 demodulator
driver, and a USB device ID in dvb-usb-ids.h .
This is v3.5 of the proposed patch, based on feedback from Sean
Young and Antti Palosaari.
Tested by patch author on DVB(T/T2/C).
Tested by Frank Rysanek on a T230C v2: can tune into locally
available DVB-T and DVB-T2 muxes, video and audio playback works.
Applies cleanly against Linux 5.2 .
The T230C v2 hardware needs a mode of the si2168 chip to be
set for which the si2168 driver previously had no support.
This patch uses a specific measure to configure this on the
T230C v2 hardware only - see the flag passed via the ts_mode
attribute and its dependency on USB_PID_MYGICA_T230C2. Other
devices using the si2168 demodulator driver are not affected.
Signed-off-by: Jan Pieter van Woerkom <j...@jpvw.nl>
Tested-by: Frank Rysanek <frantisek.rysa...@post.cz>
---
diff -ru a/drivers/media/dvb-frontends/si2168.c
b/drivers/media/dvb-frontends/si2168.c
--- a/drivers/media/dvb-frontends/si2168.c 2019-07-08 00:41:56.000000000
+0200
+++ b/drivers/media/dvb-frontends/si2168.c 2019-07-09 18:47:59.514873658
+0200
@@ -82,8 +82,18 @@
dev_dbg(&client->dev, "%s acquire: %d\n", __func__, acquire);
+ /* set manual value */
+ if (dev->ts_mode & SI2168_TS_CLK_MANUAL) {
+ memcpy(cmd.args, "\x14\x00\x0d\x10\xe8\x03", 6);
+ cmd.wlen = 6;
+ cmd.rlen = 4;
+ ret = si2168_cmd_execute(client, &cmd);
+ if (ret)
+ return ret;
+ }
/* set TS_MODE property */
- memcpy(cmd.args, "\x14\x00\x01\x10\x10\x00", 6);
+ memcpy(cmd.args, "\x14\x00\x01\x10\x00\x00", 6);
Here byte at offset 4 is now 0 rather than 0x10.
+ cmd.args[4] = dev->ts_mode & (SI2168_TS_CLK_AUTO|SI2168_TS_CLK_MANUAL);
The many existing frontends which use the si2168 do have not have ts_mode
bit SI2168_TS_CLK_AUTO (0x010) set. So, this changes what is sent for
those drivers. Is that intended?
At least 2 other drivers I tested (T230 in cxusb.c and 1 anysee)
work with this bit set or clear. My guess was that it would be OK
to use 0x00. So sort of intended. I couldn't think of a simple
operation to set one bit and clear the other. I will think again. :-)
Thanks,
Sean
if (acquire)
cmd.args[4] |= dev->ts_mode;
else
diff -ru a/drivers/media/dvb-frontends/si2168.h
b/drivers/media/dvb-frontends/si2168.h
--- a/drivers/media/dvb-frontends/si2168.h 2019-07-08 00:41:56.000000000
+0200
+++ b/drivers/media/dvb-frontends/si2168.h 2019-07-09 18:47:59.514873658
+0200
@@ -30,6 +30,8 @@
#define SI2168_TS_PARALLEL 0x06
#define SI2168_TS_SERIAL 0x03
#define SI2168_TS_TRISTATE 0x00
+#define SI2168_TS_CLK_AUTO 0x10
+#define SI2168_TS_CLK_MANUAL 0x20
u8 ts_mode;
/* TS clock inverted */
