Hi Kieran, thanks for review On Tue, Dec 11, 2018 at 11:52:03PM +0000, Kieran Bingham wrote: > Hi Jacopo, > > On 11/12/2018 15:16, Jacopo Mondi wrote: > > Re-work the chip reset procedure to configure the CP (HDMI) and SD (AFE) > > cores > > before resetting the MIPI CSI-2 TXs. > > > > Signed-off-by: Jacopo Mondi <[email protected]> > > --- > > drivers/media/i2c/adv748x/adv748x-core.c | 24 ++++++++++-------------- > > 1 file changed, 10 insertions(+), 14 deletions(-) > > > > diff --git a/drivers/media/i2c/adv748x/adv748x-core.c > > b/drivers/media/i2c/adv748x/adv748x-core.c > > index d94c63cb6a2e..5495dc7891e8 100644 > > --- a/drivers/media/i2c/adv748x/adv748x-core.c > > +++ b/drivers/media/i2c/adv748x/adv748x-core.c > > @@ -353,9 +353,8 @@ static const struct adv748x_reg_value > > adv748x_sw_reset[] = { > > {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */ > > }; > > > > -/* Supported Formats For Script Below */ > > -/* - 01-29 HDMI to MIPI TxA CSI 4-Lane - RGB888: */ > > Is this information redundant ? (CSI-4Lane, RGB888 configuration?) >
The CSI-2 data lane configuration has been break out from this table
by Niklas' patches. I've tried also moving the format configuration
out of this, but I haven't sent that change. The HDMI video direction
is now handled at link setup time, so I guess the only relevant
information is about the RGB888 format configured on the CP backend.
I'll keep that.
> > -static const struct adv748x_reg_value adv748x_init_txa_4lane[] = {
> > +/* Initialize CP Core. */
> > +static const struct adv748x_reg_value adv748x_init_hdmi[] = {
>
> While we're here - is there much scope - or value in changing these
> tables to functions with parameters using Niklas' adv748x_write_check() ?
>
> The suggestion only has value if there are parameters that we would need
> to configure. So it might be reasonable to leave these tables.
>
Right now I don't see much value in that. I would prefer breaking out
the format configuration from this static tables, but that's for
later.
> A general Ack on renaming to the function instead of the
> TX/configuration though - as that makes the purpose clearer.
>
>
> > /* Disable chip powerdown & Enable HDMI Rx block */
> > {ADV748X_PAGE_IO, 0x00, 0x40},
> >
> > @@ -399,10 +398,8 @@ static const struct adv748x_reg_value
> > adv748x_init_txa_4lane[] = {
> > {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */
> > };
> >
> > -/* 02-01 Analog CVBS to MIPI TX-B CSI 1-Lane - */
> > -/* Autodetect CVBS Single Ended In Ain 1 - MIPI Out */
> > -static const struct adv748x_reg_value adv748x_init_txb_1lane[] = {
> > -
>
> Same comments as above really :)
>
I'll see what I can keep.
Thanks
j
> > +/* Initialize AFE core. */
> > +static const struct adv748x_reg_value adv748x_init_afe[] = {
> > {ADV748X_PAGE_IO, 0x00, 0x30}, /* Disable chip powerdown Rx */
> > {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */
> >
> > @@ -445,19 +442,18 @@ static int adv748x_reset(struct adv748x_state *state)
> > if (ret < 0)
> > return ret;
> >
> > - /* Init and power down TXA */
> > - ret = adv748x_write_regs(state, adv748x_init_txa_4lane);
> > + /* Initialize CP and AFE cores. */
> > + ret = adv748x_write_regs(state, adv748x_init_hdmi);
> > if (ret)
> > return ret;
> >
> > - adv748x_tx_power(&state->txa, 1);
> > - adv748x_tx_power(&state->txa, 0);
> > -
> > - /* Init and power down TXB */
> > - ret = adv748x_write_regs(state, adv748x_init_txb_1lane);
> > + ret = adv748x_write_regs(state, adv748x_init_afe);
> > if (ret)
> > return ret;
> >
> > + /* Reset TXA and TXB */
> > + adv748x_tx_power(&state->txa, 1);
> > + adv748x_tx_power(&state->txa, 0);
> > adv748x_tx_power(&state->txb, 1);
> > adv748x_tx_power(&state->txb, 0);
> >
> > --
> > 2.7.4
> >
>
> --
> Regards
> --
> Kieran
signature.asc
Description: PGP signature
