Am Mittwoch, den 08.07.2009, 21:07 +0200 schrieb
eric.patur...@orange.fr:
> > Hi Eric,
> >
> > yes, arbitration lost on i2c is an error condition.
> >
> > As far I know we did not change the bus speed or anything, but some
> > cards need and i2c quirk to work correctly with the clients.
> >
> > Mike recently changed the old quirk with good reasons and it was widely
> > tested, also by me, without any negative effect seen.
> >
> > Maybe your card is a rare case needing the old quirk.
> >
> > You could try to change the quirk in saa7134-i2c.c
> >
> > static int saa7134_i2c_xfer(struct i2c_adapter *i2c_adap,
> > struct i2c_msg *msgs, int num)
> > {
> > struct saa7134_dev *dev = i2c_adap->algo_data;
> > enum i2c_status status;
> > unsigned char data;
> > int addr,rc,i,byte;
> >
> > status = i2c_get_status(dev);
> > if (!i2c_is_idle(status))
> > if (!i2c_reset(dev))
> > return -EIO;
> >
> > d2printk("start xfer\n");
> > d1printk(KERN_DEBUG "%s: i2c xfer:",dev->name);
> > for (i = 0; i < num; i++) {
> > if (!(msgs[i].flags & I2C_M_NOSTART) || 0 == i) {
> > /* send address */
> > d2printk("send address\n");
> > addr = msgs[i].addr << 1;
> > if (msgs[i].flags & I2C_M_RD)
> > addr |= 1;
> > if (i > 0 && msgs[i].flags & I2C_M_RD && msgs[i].addr
> > != 0x40) {
> > /* workaround for a saa7134 i2c bug
> > * needed to talk to the mt352 demux
> > * thanks to pinnacle for the hint */
> > int quirk = 0xfe;
> > <--------------------------------------
> > d1printk(" [%02x quirk]",quirk);
> > i2c_send_byte(dev,START,quirk);
> > i2c_recv_byte(dev);
> > }
> >
> > back to 0xfd.
> >
> > Cheers,
> > Hermann
> >
>
> H Hermann
>
> thanks for your suggestion .
> No improvement with changing the quirk to 0xfd ,
> I still get the same error messages :
> i2c-adapter i2c-1: Invalid 7-bit address 0x7a
> saa7133[0]: i2c xfer: < 8e >
> input: i2c IR (Pinnacle PCTV) as /class/input/input4
> ir-kbd-i2c: i2c IR (Pinnacle PCTV) detected at i2c-1/1-0047/ir0 [saa7133[0]]
> saa7133[0]: i2c xfer: < 8f ERROR: ARB_LOST
> saa7133[0]: i2c xfer: < 84 ERROR: NO_DEVICE
> saa7133[0]: i2c xfer: < 86 ERROR: ARB_LOST
> saa7133[0]: i2c xfer: < 94 ERROR: NO_DEVICE
> saa7133[0]: i2c xfer: < 96 ERROR: ARB_LOST
> saa7133[0]: i2c xfer: < c0 ERROR: NO_DEVICE
> saa7133[0]: i2c xfer: < c2 ERROR: NO_DEVICE
> saa7133[0]: i2c xfer: < c4 ERROR: NO_DEVICE
> saa7133[0]: i2c xfer: < c6 ERROR: NO_DEVICE
> saa7133[0]: i2c xfer: < c8 ERROR: NO_DEVICE
>
>
> Regards
>
Hi Eric,
thanks for your time and testing.
Before we need to start with v4l-dvb bisecting.
There have only been a few changes for the saa7134 driver since what
Mauro did send for 2.6.30.
Mostly for ir-kbd-i2c and for your remote was no tester found.
All i2c errors seem to start from the remote and that i2c remote stuff I
don't have and can't fake.
Did you try with options saa7134 disable_ir=1 already too?
Cheers,
Hermann
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
