Add the generic LED and I2C-mux support needed to describe peripherals
behind the FPGA I2C controller, then use it to instantiate the R4006 and
Time Card V9 board topologies from software nodes.
Patches 1 and 2 add the binding and LED-class driver for the Lumissil
IS32FL3207. The driver supports individual and multicolor LEDs, enforces
per-output current limits, and keeps the controller shut down until every
channel has been configured.
Patch 3 propagates software-node channel descriptions to adapters created
by i2c-mux, including a software node attached behind a primary ACPI node.
Patch 4 adds the R4006 profile for the temperature, humidity, pressure,
GNSS LED, and four SMA LEDs. The BNO08x channel remains empty because no
upstream driver binds that device. Profile selection is fail-closed and
requires a supported PCI device plus a printable fixed-width EEPROM ID
with valid padding and an R4006 prefix.
Patch 5 adds the V9 BME280, BNO055, two GNSS LEDs, and four SMA LEDs. It
uses the exact EEPROM ID "TIMECARD-V9" because earlier revisions expose
the same detectable I2C devices with different LED routing.
The prerequisite patches touch DT bindings, LED, and I2C code. Reviews or
acks from those maintainers are requested so the complete dependency
series can be carried through net-next.
Hardware and build validation:
- Exercised the R4006 LED routing on hardware.
- Checked the V9 controller address, 4.7 kohm RISET, sequential RGB
routing, and second GNSS LED against the V9 schematic.
- Ran dt_binding_check for issi,is32fl3207.yaml.
- Built i2c-mux.o, leds-is32fl3207.o, and ptp_ocp.o with W=1 for x86-64
and arm64 using both defconfig and allmodconfig.
- Ran strict checkpatch with an 80-column limit on all five patches.
- Applied the generated mailbox to the stated base and compared the
resulting tree with the source branch.
Changes since v3:
- Carry Krzysztof Kozlowski's Reviewed-by tag on the DT binding.
- Document that registers remain accessible with SDB low, preserving the
retained-scaling clear before hardware shutdown is released.
- Establish any ACPI primary before attaching the channel software node.
- Keep channel software nodes attached until child clients have been
removed, then release the held node reference after adapter deletion.
- Rebase onto current net-next.
v3:
https://lore.kernel.org/r/[email protected]/
Ahmad Byagowi (5):
dt-bindings: leds: Add IS32FL3207 controller
leds: is32fl3207: Add controller driver
i2c: mux: Propagate software nodes to channel adapters
ptp: ocp: Add R4006 I2C peripheral topology
ptp: ocp: Add Time Card V9 I2C peripheral topology
.../bindings/leds/issi,is32fl3207.yaml | 251 +++++
MAINTAINERS | 7 +
drivers/i2c/i2c-mux.c | 71 +-
drivers/leds/rgb/Kconfig | 11 +
drivers/leds/rgb/Makefile | 1 +
drivers/leds/rgb/leds-is32fl3207.c | 691 ++++++++++++++
drivers/ptp/ptp_ocp.c | 881 +++++++++++++++++-
7 files changed, 1865 insertions(+), 48 deletions(-)
create mode 100644 Documentation/devicetree/bindings/leds/issi,is32fl3207.yaml
create mode 100644 drivers/leds/rgb/leds-is32fl3207.c
base-commit: ac155a26750a595703e7dadff84735456d75a479
--
2.50.1 (Apple Git-155)
