+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - VA-supply
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ codec@40 {
+ compatible = "cirrus,cs35l36";
+ reg = <0x40>;
+ VA-supply = <&dummy_vreg>;
+ VP-supply = <&dummy_vreg>;
+ reset-gpios = <&gpio0 54 GPIO_ACTIVE_HIGH>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ cirrus,boost-ind-nanohenry = <1000>;
+ cirrus,boost-ctl-millivolt = <10000>;
+ cirrus,boost-peak-milliamp = <4500>;
+ cirrus,boost-ctl-select = <0x00>;
+ cirrus,weak-fet-delay = <4>;
+ cirrus,weak-fet-thld = <0x01>;
+ cirrus,temp-warn-threshold = <1>;
+ cirrus,multi-amp-mode;
+ cirrus,irq-drive-select = <1>;
+ cirrus,irq-gpio-select = <0x01>;
+
+ cirrus,vpbr-config {
+ cirrus,vpbr-en = <0>;
+ cirrus,vpbr-thld = <0x05>;
+ cirrus,vpbr-atk-rate = <0x02>;
+ cirrus,vpbr-atk-vol = <0x01>;
+ cirrus,vpbr-max-attn = <0x09>;
+ cirrus,vpbr-wait = <0x01>;
+ cirrus,vpbr-rel-rate = <0x05>;
+ cirrus,vpbr-mute-en = <0x00>;
+ };
+ };
+ };
+...
diff --git a/Documentation/devicetree/bindings/sound/cs35l36.txt
b/Documentation/devicetree/bindings/sound/cs35l36.txt
deleted file mode 100644
index d34117b8558e5..0000000000000
--- a/Documentation/devicetree/bindings/sound/cs35l36.txt
+++ /dev/null
@@ -1,168 +0,0 @@
-CS35L36 Speaker Amplifier
-
-Required properties:
-
- - compatible : "cirrus,cs35l36"
-
- - reg : the I2C address of the device for I2C
-
- - VA-supply, VP-supply : power supplies for the device,
- as covered in
- Documentation/devicetree/bindings/regulator/regulator.txt.
-
- - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
- converter's output voltage in mV. The range is from 2550mV to 12000mV with
- increments of 50mV.
- (Default) VP
-
- - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
- Configures the peak current by monitoring the current through the boost FET.
- Range starts at 1600mA and goes to a maximum of 4500mA with increments of
- 50mA.
- (Default) 4.50 Amps
-
- - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
- Seeds the digital boost converter's inductor estimation block with the
initial
- inductance value to reference.
-
- 1000 = 1uH (Default)
- 1200 = 1.2uH
-
-Optional properties:
- - cirrus,multi-amp-mode : Boolean to determine if there are more than
- one amplifier in the system. If more than one it is best to Hi-Z the ASP
- port to prevent bus contention on the output signal
-
- - cirrus,boost-ctl-select : Boost converter control source selection.
- Selects the source of the BST_CTL target VBST voltage for the boost
- converter to generate.
- 0x00 - Control Port Value
- 0x01 - Class H Tracking (Default)
- 0x10 - MultiDevice Sync Value
-
- - cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming
- PCM data
-
- - cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the
- polarity of outbound IMON feedback data
-
- - cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the
- polarity of outbound VMON feedback data
-
- - cirrus,dcm-mode-enable : Boost converter automatic DCM Mode enable.
- This enables the digital boost converter to operate in a low power
- (Discontinuous Conduction) mode during low loading conditions.
-
- - cirrus,weak-fet-disable : Boolean : The strength of the output drivers is
- reduced when operating in a Weak-FET Drive Mode and must not be used to drive
- a large load.
-
- - cirrus,classh-wk-fet-delay : Weak-FET entry delay. Controls the delay
- (in ms) before the Class H algorithm switches to the weak-FET voltage
- (after the audio falls and remains below the value specified in
WKFET_AMP_THLD).
-
- 0 = 0ms
- 1 = 5ms
- 2 = 10ms
- 3 = 50ms
- 4 = 100ms (Default)
- 5 = 200ms
- 6 = 500ms
- 7 = 1000ms
-
- - cirrus,classh-weak-fet-thld-millivolt : Weak-FET amplifier drive threshold.
- Configures the signal threshold at which the PWM output stage enters
- weak-FET operation. The range is 50mV to 700mV in 50mV increments.
-
- - cirrus,temp-warn-threshold : Amplifier overtemperature warning threshold.
- Configures the threshold at which the overtemperature warning condition
occurs.
- When the threshold is met, the overtemperature warning attenuation is applied
- and the TEMP_WARN_EINT interrupt status bit is set.
- If TEMP_WARN_MASK = 0, INTb is asserted.
-
- 0 = 105C
- 1 = 115C
- 2 = 125C (Default)
- 3 = 135C
-
- - cirrus,irq-drive-select : Selects the driver type of the selected interrupt
- output.
-
- 0 = Open-drain
- 1 = Push-pull (Default)
-
- - cirrus,irq-gpio-select : Selects the pin to serve as the programmable
- interrupt output.
-
- 0 = PDM_DATA / SWIRE_SD / INT (Default)
- 1 = GPIO
-
-Optional properties for the "cirrus,vpbr-config" Sub-node
-
- - cirrus,vpbr-en : VBST brownout prevention enable. Configures whether the
- VBST brownout prevention algorithm is enabled or disabled.
-
- 0 = VBST brownout prevention disabled (default)
- 1 = VBST brownout prevention enabled
-
- See Section 7.31.1 VPBR Config for configuration options & further details
-
- - cirrus,vpbr-thld : Initial VPBR threshold. Configures the VP brownout
- threshold voltage
-
- - cirrus,cirrus,vpbr-atk-rate : Attenuation attack step rate. Configures the
- amount delay between consecutive volume attenuation steps when a brownout
- condition is present and the VP brownout condition is in an attacking state.
-
- - cirrus,vpbr-atk-vol : VP brownout prevention step size. Configures the VP
- brownout prevention attacking attenuation step size when operating in either
- digital volume or analog gain modes.
-
- - cirrus,vpbr-max-attn : Maximum attenuation that the VP brownout prevention
- can apply to the audio signal.
-
- - cirrus,vpbr-wait : Configures the delay time between a brownout condition
- no longer being present and the VP brownout prevention entering an
attenuation
- release state.
-
- - cirrus,vpbr-rel-rate : Attenuation release step rate. Configures the delay
- between consecutive volume attenuation release steps when a brownout
condition
- is not longer present and the VP brownout is in an attenuation release state.
-
- - cirrus,vpbr-mute-en : During the attack state, if the vpbr-max-attn value
- is reached, the error condition still remains, and this bit is set, the audio
- is muted.
-
-Example:
-
-cs35l36: cs35l36@40 {
- compatible = "cirrus,cs35l36";
- reg = <0x40>;
- VA-supply = <&dummy_vreg>;
- VP-supply = <&dummy_vreg>;
- reset-gpios = <&gpio0 54 0>;
- interrupt-parent = <&gpio8>;
- interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
-
- cirrus,boost-ind-nanohenry = <1000>;
- cirrus,boost-ctl-millivolt = <10000>;
- cirrus,boost-peak-milliamp = <4500>;
- cirrus,boost-ctl-select = <0x00>;
- cirrus,weak-fet-delay = <0x04>;
- cirrus,weak-fet-thld = <0x01>;
- cirrus,temp-warn-threshold = <0x01>;
- cirrus,multi-amp-mode;
- cirrus,irq-drive-select = <0x01>;
- cirrus,irq-gpio-select = <0x01>;
-
- cirrus,vpbr-config {
- cirrus,vpbr-en = <0x00>;
- cirrus,vpbr-thld = <0x05>;
- cirrus,vpbr-atk-rate = <0x02>;
- cirrus,vpbr-atk-vol = <0x01>;
- cirrus,vpbr-max-attn = <0x09>;
- cirrus,vpbr-wait = <0x01>;
- cirrus,vpbr-rel-rate = <0x05>;
- cirrus,vpbr-mute-en = <0x00>;
- };
-};
---
base-commit: 8cd9520d35a6c38db6567e97dd93b1f11f185dc6
change-id: 20260618-dt-cirrus-cs35l36-99c466fb13fd
Best regards,
--
David Heidelberg <[email protected]>
