Here are a few sub-tests for mptcp_join.sh, validating the new 'laminar' endpoint type.
In a setup where subflows created using the routing rules would be rejected by the listener, and where the latter announces one IP address, some cases are verified: - Without any 'laminar' endpoints: no new subflows are created. - With one 'laminar' endpoint: a second subflow is created. - With multiple 'laminar' endpoints: 2 IPv4 subflows are created. - With one 'laminar' endpoint, but the server announcing a second IP address, only one subflow is created. - With one 'laminar' + 'subflow' endpoint, the same endpoint is only used once. Reviewed-by: Mat Martineau <[email protected]> Signed-off-by: Matthieu Baerts (NGI0) <[email protected]> --- tools/testing/selftests/net/mptcp/mptcp_join.sh | 69 +++++++++++++++++++++++++ tools/testing/selftests/net/mptcp/pm_nl_ctl.c | 9 ++++ 2 files changed, 78 insertions(+) diff --git a/tools/testing/selftests/net/mptcp/mptcp_join.sh b/tools/testing/selftests/net/mptcp/mptcp_join.sh index a94b3960ad5e009dbead66b6ff2aa01f70aa3e1f..c90d8e8b95cbb6ba80f79208d1cc844673f2c249 100755 --- a/tools/testing/selftests/net/mptcp/mptcp_join.sh +++ b/tools/testing/selftests/net/mptcp/mptcp_join.sh @@ -2320,6 +2320,74 @@ signal_address_tests() fi } +laminar_endp_tests() +{ + # no laminar endpoints: routing rules are used + if reset_with_tcp_filter "without a laminar endpoint" ns1 10.0.2.2 REJECT && + mptcp_lib_kallsyms_has "mptcp_pm_get_endp_laminar_max$"; then + pm_nl_set_limits $ns1 0 2 + pm_nl_set_limits $ns2 2 2 + pm_nl_add_endpoint $ns1 10.0.2.1 flags signal + run_tests $ns1 $ns2 10.0.1.1 + join_syn_tx=1 \ + chk_join_nr 0 0 0 + chk_add_nr 1 1 + fi + + # laminar endpoints: this endpoint is used + if reset_with_tcp_filter "with a laminar endpoint" ns1 10.0.2.2 REJECT && + mptcp_lib_kallsyms_has "mptcp_pm_get_endp_laminar_max$"; then + pm_nl_set_limits $ns1 0 2 + pm_nl_set_limits $ns2 2 2 + pm_nl_add_endpoint $ns1 10.0.2.1 flags signal + pm_nl_add_endpoint $ns2 10.0.3.2 flags laminar + run_tests $ns1 $ns2 10.0.1.1 + chk_join_nr 1 1 1 + chk_add_nr 1 1 + fi + + # laminar endpoints: these endpoints are used + if reset_with_tcp_filter "with multiple laminar endpoints" ns1 10.0.2.2 REJECT && + mptcp_lib_kallsyms_has "mptcp_pm_get_endp_laminar_max$"; then + pm_nl_set_limits $ns1 0 2 + pm_nl_set_limits $ns2 2 2 + pm_nl_add_endpoint $ns1 10.0.2.1 flags signal + pm_nl_add_endpoint $ns1 10.0.3.1 flags signal + pm_nl_add_endpoint $ns2 dead:beef:3::2 flags laminar + pm_nl_add_endpoint $ns2 10.0.3.2 flags laminar + pm_nl_add_endpoint $ns2 10.0.4.2 flags laminar + run_tests $ns1 $ns2 10.0.1.1 + chk_join_nr 2 2 2 + chk_add_nr 2 2 + fi + + # laminar endpoints: only one endpoint is used + if reset_with_tcp_filter "single laminar endpoint" ns1 10.0.2.2 REJECT && + mptcp_lib_kallsyms_has "mptcp_pm_get_endp_laminar_max$"; then + pm_nl_set_limits $ns1 0 2 + pm_nl_set_limits $ns2 2 2 + pm_nl_add_endpoint $ns1 10.0.2.1 flags signal + pm_nl_add_endpoint $ns1 10.0.3.1 flags signal + pm_nl_add_endpoint $ns2 10.0.3.2 flags laminar + run_tests $ns1 $ns2 10.0.1.1 + chk_join_nr 1 1 1 + chk_add_nr 2 2 + fi + + # laminar endpoints: subflow and laminar flags + if reset_with_tcp_filter "sublow + laminar endpoints" ns1 10.0.2.2 REJECT && + mptcp_lib_kallsyms_has "mptcp_pm_get_endp_laminar_max$"; then + pm_nl_set_limits $ns1 0 4 + pm_nl_set_limits $ns2 2 4 + pm_nl_add_endpoint $ns1 10.0.2.1 flags signal + pm_nl_add_endpoint $ns2 10.0.1.2 flags subflow,laminar + pm_nl_add_endpoint $ns2 10.0.3.2 flags subflow,laminar + run_tests $ns1 $ns2 10.0.1.1 + chk_join_nr 1 1 1 + chk_add_nr 1 1 + fi +} + link_failure_tests() { # accept and use add_addr with additional subflows and link loss @@ -4109,6 +4177,7 @@ all_tests_sorted=( f@subflows_tests e@subflows_error_tests s@signal_address_tests + L@laminar_endp_tests l@link_failure_tests t@add_addr_timeout_tests r@remove_tests diff --git a/tools/testing/selftests/net/mptcp/pm_nl_ctl.c b/tools/testing/selftests/net/mptcp/pm_nl_ctl.c index d4981b76693bbddca74169437a540ad6294cf1d5..65b374232ff5ac06876dcd621fd2109c4d82cd12 100644 --- a/tools/testing/selftests/net/mptcp/pm_nl_ctl.c +++ b/tools/testing/selftests/net/mptcp/pm_nl_ctl.c @@ -830,6 +830,8 @@ int add_addr(int fd, int pm_family, int argc, char *argv[]) flags |= MPTCP_PM_ADDR_FLAG_SUBFLOW; else if (!strcmp(tok, "signal")) flags |= MPTCP_PM_ADDR_FLAG_SIGNAL; + else if (!strcmp(tok, "laminar")) + flags |= MPTCP_PM_ADDR_FLAG_LAMINAR; else if (!strcmp(tok, "backup")) flags |= MPTCP_PM_ADDR_FLAG_BACKUP; else if (!strcmp(tok, "fullmesh")) @@ -1018,6 +1020,13 @@ static void print_addr(struct rtattr *attrs, int len) printf(","); } + if (flags & MPTCP_PM_ADDR_FLAG_LAMINAR) { + printf("laminar"); + flags &= ~MPTCP_PM_ADDR_FLAG_LAMINAR; + if (flags) + printf(","); + } + if (flags & MPTCP_PM_ADDR_FLAG_BACKUP) { printf("backup"); flags &= ~MPTCP_PM_ADDR_FLAG_BACKUP; -- 2.51.0
